Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Page 1 of 2 12 LastLast
Results 1 to 15 of 29

Thread: twin tuner set advice

  1. #1

    Title
    Senior Member
    Join Date
    Jan 2011
    Posts
    289
    Thanks
    19
    Thanked 4 Times in 3 Posts

    twin tuner set advice

    I want to know what is the best way to set up twin tuner.

    I have an 80 cm motorised dish & sly dish set up.

    downstairs in the house I have a duo connected to the sly dish & my motorised dish, but it dose not control the motor.

    upstairs I have the venton connected to the motorised dish only.


    what is the best way to set the twin tuner up.

    should I change the dual lnb to a quad lnb on the motorised dish.

    or should I take one the of the feeds from the sly quad & connect it to the venton is that possible.

  2. #2

    Title
    Senior Member
    Join Date
    Jan 2011
    Posts
    289
    Thanks
    19
    Thanked 4 Times in 3 Posts
    is there a way to set the box up with the motor without using usals
    the box is not locking onto the sat.

    I have the limits of but the eat or west is not moving, but when I go to calibrate it moves the dish but I get the error no signal.

    when I move the dish with the spiderbox then plug the cable back into the box it works ok

    any ideas?

  3. #3
    Larry-G's Avatar
    Title
    V.I.P
    Donated Member
    Join Date
    May 2010
    Posts
    32,542
    Thanks
    7,824
    Thanked 22,937 Times in 12,378 Posts
    you can use this to setup without usals but it's a very long winded process.
    My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.

    If you don't like what I post, Don't read it.

    SIMPLES.

  4. #4

    Title
    Senior Member
    Join Date
    Jan 2011
    Posts
    289
    Thanks
    19
    Thanked 4 Times in 3 Posts
    Quote Originally Posted by pheonix View Post
    you can use this to setup without usals but it's a very long winded process.
    cheers mate I will give it ago

  5. #5

    Title
    Senior Member
    Join Date
    Jan 2011
    Posts
    289
    Thanks
    19
    Thanked 4 Times in 3 Posts
    Quote Originally Posted by pheonix View Post
    you can use this to setup without usals but it's a very long winded process.
    hi mate

    I have tried several times following the pdf but I can the box to pick up the 1st sat I put in but when I try to put the second sat up nothing happens it dose not logon to the sat.

    I know I have the sat locked as a I navigate to the sats position ok with the spiderbox but get no signal any ideas

  6. #6

    Title
    Senior Member
    Join Date
    Jan 2011
    Posts
    289
    Thanks
    19
    Thanked 4 Times in 3 Posts
    I am using a dual lnb

  7. #7

    Title
    Senior Member
    Join Date
    Jan 2011
    Posts
    289
    Thanks
    19
    Thanked 4 Times in 3 Posts
    Quote Originally Posted by abu baniaz View Post
    Posted in error.

    Please delete
    I will give it ago

  8. #8

    Title
    Senior Member
    Join Date
    Jan 2011
    Posts
    289
    Thanks
    19
    Thanked 4 Times in 3 Posts
    Quote Originally Posted by abu baniaz View Post
    Posted in error.

    Please delete
    ok I wont then

  9. #9
    abu baniaz's Avatar
    Title
    Moderator
    Join Date
    Sep 2010
    Location
    East London
    Posts
    23,541
    Thanks
    6,517
    Thanked 9,224 Times in 6,287 Posts
    You can only move the dish with one receiver. Can we concentrate on the motorised dish for the moment, we can tackle teh 28.2 dish later? Can you also confirm the following?

    A. Do you have any diseqc switches/splitters in the setup?

    B. How many receivers will be connected to the motorised dish?
    C. Which receiver do you want to control the motor?
    D. Does "dish controlling receiver" have the "motor cable" connected to it

    Regarding the second cable of the lnb on the motorised dish, "non-motor cable".
    E. Which receiver and dish input is the non-motor cable connected to?
    F. what is the tuner config for said dish input/tuner.

  10. #10

    Title
    Senior Member
    Join Date
    Jan 2011
    Posts
    289
    Thanks
    19
    Thanked 4 Times in 3 Posts
    a it has no switches or splitters connected to it bit is using the internal diseqc 1.2
    b the dish has two recievers connected to it
    c the venton
    d yes, when I remove the cable from the venton & connect the spiderbox with the same cable the spiderbox picks up the signal.

    e not sure as I never set the dish up


    f simple then the sat name

  11. #11
    abu baniaz's Avatar
    Title
    Moderator
    Join Date
    Sep 2010
    Location
    East London
    Posts
    23,541
    Thanks
    6,517
    Thanked 9,224 Times in 6,287 Posts
    Answers E & F are incomplete. As they do not affect the motor controls (provided you have not mixed up the wires) it can be ignored for now.

    I would suggest you treat things in isolation. The priority is that we get the Venton controlling the motor.

    G. Identify your cables and label them.
    H. Verify you do not have a faulty tuner one at a time.
    Set all tuners to "not configured". Connect the 28.2 satellite cable and set to relevant tuner to
    Simple. Single, 28.2

    I. Once conformed that the tuner is not faulty, connect the "motor cable" to the Venton tuner and proceed to configure with other tuners disabled and no other satellite cables connected. I would attempt USALS first.
    J. Report back if the dish moves and whether it locks on to the satellite.

  12. #12

    Title
    Senior Member
    Join Date
    Jan 2011
    Posts
    289
    Thanks
    19
    Thanked 4 Times in 3 Posts
    hi sorry for the delay I have did the above but it is not moving my dish, I have had my dish aligned it work perfercty with my spiderbox.

    tuner a & b both work with the sky cable.

    when I try to move the dish usal I get tuner config error

    any ideas

  13. #13

    Title
    Senior Member
    Join Date
    Jan 2011
    Posts
    289
    Thanks
    19
    Thanked 4 Times in 3 Posts
    I am using wannabes motor channel list & the lnb on the motorised dish is a dual lnb
    what settings am I missing on the tuner config

  14. #14
    abu baniaz's Avatar
    Title
    Moderator
    Join Date
    Sep 2010
    Location
    East London
    Posts
    23,541
    Thanks
    6,517
    Thanked 9,224 Times in 6,287 Posts
    Take screen shots of your tuner config and upload please. You can also use the webinterface to do this.

  15. #15

    Title
    Senior Member
    Join Date
    Jan 2011
    Posts
    289
    Thanks
    19
    Thanked 4 Times in 3 Posts
    just done it mate
    Attached Images Attached Images

Page 1 of 2 12 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.