I saw a picture of a 'globe' with a bit of text. This then stayed unchanged for a while.
With the VIX image should the cogs be moving because mine do not move.
I saw a picture of a 'globe' with a bit of text. This then stayed unchanged for a while.
With the VIX image should the cogs be moving because mine do not move.
Moved to the correct section
When you say cogs I'm assuming you mean these in the bootlogo: -
No they are static, part of the bootlogo.
Sounds like your flashing the image OK, but not leaving enough time for it to start fully and go into the startupwizard. After flashing leave for a few mins and let it do its stuff on reboot![]()
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
What happens when you press "Menu" button?
EDIT: Sic beat me to it, please ignore...
Last edited by yngvekl; 29-09-10 at 09:22.
I will try again tonight. thanks for your help.
I have tried the menu button plus others without any affect.
It take a couple of mins to get to the startup wizard, you need to have patience and leave it to boot. The next screen that will appear is this: -
After the above you will get the startup wizard![]()
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
I tried your advice but after 20 minutes nothing had happened. In desperation I tried taking out the ethernet cable and I got to the wizard. I think the problem was that I had tried to change the router to give the Vu a fixed IP address but it was not set properly so this was causing a conflict.
Just got my Vu+ Duo yesterday and i too had problems flashing image with usb. It would flash. While flashing my tv screen was blank (connected via HDMI) so was relying on duo screen (maybe thats standard) when finished, id remove usb and power off/on at back switch. When rebooting i would get as far as starting enigma 2 and freeze. Tried a few times and gave up on usb. Flashed fine with serial cable.
Just like to know what i was doing wrong with usb flash?
Great image btw. Had been used to dream elite on dreambox. After a few hours i much prefer VIX. Well done guys...
One niggle i have, the info button (coloured far left, cannot remember colour, red i think) when i press this for info, the info stays until i press exit. It would be nice if it timed out or a second press of coloured button removed info. Maybe this function is there but i have not found it yet. Still on learning curve...