Hi setting up tuners not sure if to set up both the same or to put B on loopthrough. thanks for any info
Hi setting up tuners not sure if to set up both the same or to put B on loopthrough. thanks for any info
A little more info would help!!
Sent from my GT-I9100 using Tapatalk 2
Vu+Duo
Vix Hades
WD 1TB Blue Desktop Drive 3.5" SATA-III 7200RPM 64MB =Cross EPG & 256mb Swap File
Kingston DataTraveler SE9 8GB USB =PTS
Vu+Duo
Vix Hades
Seagate 500GB 3.5" SATA-III 6Gb/s Barracuda Hard Drive 7200RPM 16MB=Cross EPG & 256mb Swap File
Kingston DataTraveler SE9 8GB USB =PTS
Both Duo's Plugins, Lraizer Autobouquet, Cacheflush, Mediascanner, Picture player, Movie Browser & Openwebif
more info vu+solo2 fixed dish sly tuner a tuned for sly channels not sure if b should be on a loopthrough
I have mine both on simple, single.......I don't use loopthrough.
Sent from my GT-I9100 using Tapatalk 2
Vu+Duo
Vix Hades
WD 1TB Blue Desktop Drive 3.5" SATA-III 7200RPM 64MB =Cross EPG & 256mb Swap File
Kingston DataTraveler SE9 8GB USB =PTS
Vu+Duo
Vix Hades
Seagate 500GB 3.5" SATA-III 6Gb/s Barracuda Hard Drive 7200RPM 16MB=Cross EPG & 256mb Swap File
Kingston DataTraveler SE9 8GB USB =PTS
Both Duo's Plugins, Lraizer Autobouquet, Cacheflush, Mediascanner, Picture player, Movie Browser & Openwebif
many thanks
Hi,
only if two separate cables are connected to the box. If you only have one cable you have to put it into tuner B and A loop through to B.
ciao
---
Sat:VU+ Ultimo4K/Solo4K/Duo2/2*Solo2/Ultimo
Remote: Harmony 200, 700, Link, Smart Control, Smart Companion, Elite, 2*Ultimate, Keyboard
Vu+Duo
Vix Hades
WD 1TB Blue Desktop Drive 3.5" SATA-III 7200RPM 64MB =Cross EPG & 256mb Swap File
Kingston DataTraveler SE9 8GB USB =PTS
Vu+Duo
Vix Hades
Seagate 500GB 3.5" SATA-III 6Gb/s Barracuda Hard Drive 7200RPM 16MB=Cross EPG & 256mb Swap File
Kingston DataTraveler SE9 8GB USB =PTS
Both Duo's Plugins, Lraizer Autobouquet, Cacheflush, Mediascanner, Picture player, Movie Browser & Openwebif
I have one cable in tuner a and the config of the tuner b is loopthrought to a.
is this coorect?
why r u saying to put cable to tuner b?
thank you
hi,
what did I write in my previous post?
ciao
Gesendet von meinem GT-P1000 mit Tapatalk 2
---
Sat:VU+ Ultimo4K/Solo4K/Duo2/2*Solo2/Ultimo
Remote: Harmony 200, 700, Link, Smart Control, Smart Companion, Elite, 2*Ultimate, Keyboard
can you explain to us why we have to put cable only in tuner b and loopthrought to a?
and why not cable to tuner a and loopthrought to b?
thank you
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
i have put the cable on tuner A and i have configure tuner B to be loopthrought to A and works all ok with the channels on same sat and same polarization.
how can you explain this ,if the software doesnt support this?
thank you for your answer
Help asked via PM will be ignored.
The forum is there for help and all will benefit from your questions.
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !
English is not my native tongue.
I apologise for all my grammar, spelling and idiom errors.
very strange,in my solo2 working at pip mode,
i think that there is choice to loopthrought tuner b to tuner a,if was impossible then there isnt such a choice.
i turn on pip and i can see channels on same sat and same polarization and different provider,transpoder.
Last edited by redribo; 18-01-13 at 13:55.