Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Page 1 of 2 12 LastLast
Results 1 to 15 of 23

Thread: TM500 super corrupted

  1. #1

    Title
    Member
    Join Date
    Nov 2012
    Posts
    61
    Thanks
    4
    Thanked 1 Time in 1 Post

    TM500 super corrupted

    Hi All,
    help need please.
    My TM500 Super appears to have been corrupted. I tried re-flashing it but made a fatal mistake I think.
    I may have flashed it with the wrong image as when I power up I get the GP logo displayed on the screen. When I re-flash with the UR image that works on all my TM500s I get a 'loading error' message on screen when the progress dots have reached 100%.
    Any idea what if any thing I can try.

    Philly.

  2. #2
    bassethound's Avatar
    Title
    Forum Supporter
    Donated Member
    Join Date
    May 2010
    Location
    North West
    Posts
    5,719
    Thanks
    6,871
    Thanked 6,131 Times in 2,737 Posts
    Have you tried a TM serial update see the how to pdf below

    this way always recovers my tm 500/600 it might take a few goes trying a couple of older images good luck

    thanks to digidude for the how to
    All PM,s asking about c/s on cable will be ignored and reported to forum staff!

  3. The Following User Says Thank You to bassethound For This Useful Post:


  4. #3

    Title
    Member
    Join Date
    Nov 2012
    Posts
    61
    Thanks
    4
    Thanked 1 Time in 1 Post
    Thanks bassethound,
    I will give it a go and let you know the outcome,

    Philly

  5. #4

    Title
    Member
    Join Date
    Nov 2012
    Posts
    61
    Thanks
    4
    Thanked 1 Time in 1 Post
    Hi bassethound,
    Just read the tutorial you attached. This is the procedure that I use. When finished the on screen progress dots read 'bad flash' or similar notice (away from box at the moment so cannot check exact wording).
    The UR image that I am trying to re-flash is ur-180211.img. I never had a problem flashing this image in the past on a new box.

  6. #5
    abu baniaz's Avatar
    Title
    Moderator
    Join Date
    Sep 2010
    Location
    East London
    Posts
    23,541
    Thanks
    6,517
    Thanked 9,224 Times in 6,287 Posts
    Have you tried ticking factory reset?

  7. #6
    bassethound's Avatar
    Title
    Forum Supporter
    Donated Member
    Join Date
    May 2010
    Location
    North West
    Posts
    5,719
    Thanks
    6,871
    Thanked 6,131 Times in 2,737 Posts
    i would try flashing any other tm600/500 super image first then flash your desired image via the mini web
    Last edited by bassethound; 12-11-12 at 14:15.
    All PM,s asking about c/s on cable will be ignored and reported to forum staff!

  8. #7

    Title
    Junior Member
    Join Date
    Jan 2013
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    the same problem but when i start download ur for me showing message what pc is not responding... will retry
    whats the problem
    who can help ?
    thanks

  9. #8
    digidude
    if the image IS NOT a UR image on the box (showing GP etc when booting) then the miniweb may possibly not exist to use

    with a network cable connected, press and hold the power button when turning the power on, if a number appears in the front display, then enter this into a browser (assuming your router IP is 192.161.1.1) as 192.168.1.NUMBER and you should be able to flash

    if not, then you will need either the Technomate Control Center or the Digidude loader, and an RS232 cable

    if the software is saying PC not responding, then if you are using a USB-RS232 adaptor, then its possible the drivers are not configured correctly for the COM port to report the information being received from the receiver as you power it up

  10. #9

    Title
    Junior Member
    Join Date
    Jan 2013
    Posts
    3
    Thanks
    0
    Thanked 0 Times in 0 Posts
    i can use network cabel because ethernet not working and i using usb-rs232 cable because in my laptop going 15 male to receiver 9 female cable maybe you know how need configure com port correctly ? or wich ur image need use ?

  11. #10

    Title
    Member
    Join Date
    Nov 2012
    Posts
    61
    Thanks
    4
    Thanked 1 Time in 1 Post
    Hi digidude,
    My problem seems to be that my TM500 super does not like the UR image that I am trying to flash since I previously flashed (mistake) the box with a GP image. I know the UR image is the correct one as I have used it many time on the same model box in the past. Getting rid of the GP image seems to be the problem. Using the rs232 works but displays an error notice then 100% is reached.
    Any comments or suggestions appreciated.

  12. #11

    Title
    Junior Member
    Join Date
    Jan 2011
    Posts
    28
    Thanks
    73
    Thanked 2 Times in 2 Posts
    Quote Originally Posted by manntas View Post
    i can use network cabel because ethernet not working and i using usb-rs232 cable because in my laptop going 15 male to receiver 9 female cable maybe you know how need configure com port correctly ? or wich ur image need use ?
    you may need a rs323 to rs323 cable for it to work as usb to rs323 do not always work or look for your com port in device manager on you lappy

  13. #12

    Title
    Junior Member
    Join Date
    Jan 2011
    Posts
    28
    Thanks
    73
    Thanked 2 Times in 2 Posts
    Quote Originally Posted by philly View Post
    Hi digidude,
    My problem seems to be that my TM500 super does not like the UR image that I am trying to flash since I previously flashed (mistake) the box with a GP image. I know the UR image is the correct one as I have used it many time on the same model box in the past. Getting rid of the GP image seems to be the problem. Using the rs232 works but displays an error notice then 100% is reached.
    Any comments or suggestions appreciated.
    did you do a factory reset before you flashed if yes try an older image

  14. #13

    Title
    Member
    Join Date
    Nov 2012
    Posts
    61
    Thanks
    4
    Thanked 1 Time in 1 Post

    old UR image

    Quote Originally Posted by dathai60 View Post
    did you do a factory reset before you flashed if yes try an older image
    Thanks dathaid,
    I did try the factory reset in the past with no joy. I may have tried a different image but got error message also. Maybe there is a specific old image that I need to try.

  15. #14

    Title
    Junior Member
    Join Date
    Jan 2011
    Posts
    28
    Thanks
    73
    Thanked 2 Times in 2 Posts
    did you use tcc 7.1 to change image

  16. #15

    Title
    Member
    Join Date
    Nov 2012
    Posts
    61
    Thanks
    4
    Thanked 1 Time in 1 Post
    Quote Originally Posted by dathai60 View Post
    did you use tcc 7.1 to change image
    I always use tcc 7.1. However in the current faulty state with GP displayed on screen The only way I can connect to the box is using serial cable.

Page 1 of 2 12 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.