Freezing and mosaicing

[Sicilian]

chip face down in the card readers in the smargo chip up.

[Sicilian]

Ok, tested. Imo the ecm times reported by the ET9000 are wrong. Picture is spot on, no glitching/freezing whatsoever.

Top slot: -
BOXKEY: /dev/sci1 XX XX XX XX
SMARTCARD CLOCK FREQUENCY: /dev/sci1 3580000

Bottom slot: -
BOXKEY: /dev/sci1 XX XX XX XX
SMARTCARD CLOCK FREQUENCY: /dev/sci1 3580000

Smago: -
BOXKEY: /dev/ttyUSB0 XX XX XX XX
SERIAL READER : /dev/ttyUSB0
SMARTCARD CLOCK FREQENCY : /dev/ttyUSB0 6000000

Tested as a client too (we wont talk any further about that).

Tested with CCcam 2.1.3 & 2.2.1.

[canthackit]

nightmare.

i've now put the BH image on (bit ancient still refers to the DVI connection)

now running cccam 2.2.0

disabled everything (you know what i mean)

card in lower slot, chip down

it's on /sci1

and nothing blank screen.

i've tried putting the cccam 2.2.1 i have still nothing got a feeling my version won't work

but anyway still on 2.2.0 and nothing

so come on guy's what am i doing wrong

your obidient servent
canthackit....................it's never been truer

[canthackit]

cant believe it

4 pages and i still aint sussed it

[Sicilian]

Check your pm.

[canthackit]

this is getting crazy i'm in the process of going back to the vix image.

now i cant get the bloody thing to install, it just sits there saying flashing and nothing is happening, i've tried both versions posted here the one with the updated drivers and the one without, and neither will install.

Black Hole went on ok...so what am i doing wrong with VIX?

i don't believe that this image takes 5 minutes to install let alone the 10 mins i've left it for now, this just gets sillier and sillier

i need to get this sorted now before i can even go back to the card problem

regards: canthackit

[Donnie]

Can't help with the flashing but you need to use the VIX image as the BH one is old and it was known that the drivers were no good for the internal card readers at the time of release.

[canthackit]

ok thanks mate but as the post above say's.

i cant get the bloody thing on there.

i'm in the process of downloading and trying to install yet again and the bleedin' is just sitting there saying "flashing"

[pooface]

Have u tried formatting the usb stick, and then copy the files over again?

Sent from my MB511 using Tapatalk

[canthackit]

about 15 times now mate over the course of a couple of hours.

i've tried the front usb port the rear usb ports, i've formatted the pen everytime i'm on a mac so it was ms-dos fat copied over the et9000 folder with the 4 files, power off, put the usb in the front port, power on, it recognises the VIX image then when it says ready press ok button on the front panel......................
then wait 30 mins while it says "flashing"..................................i' m still waiting it's never going to install.

the only other thing i've just found another usb pen i'm going to try that.


regards: canthackit

[Alias1]

Try loading the factory image on it

[Donnie]

Have you tried flashing with everything else disconected such as sat cable, HDMI, HDD, smagro and anything that can be removed remove.

[canthackit]

ok going to try disconnecting everything to install the vix image if that dont work, i'll try with everything disconnected to install the factory image.

i'm on the point of thinking about asking steffan if there's any possibiltiy of exchanging this box for another Duo, he can only say "No"...............or sod off

thanks & regards: canthackit

[canthackit]

everything disconnected the VIX image wont install

[Donnie]

Does this box offer another way to flash such as via a serial port ?