Hi, I have a vu+solo which is stuck in standby, showing the vu+solo on the front panel. Have tried the usual quick fixes of turning power off and on and changed the remote batteries but no change. Any ideas folks?
Hi, I have a vu+solo which is stuck in standby, showing the vu+solo on the front panel. Have tried the usual quick fixes of turning power off and on and changed the remote batteries but no change. Any ideas folks?
Solo or Solo2?
Sent from my iPhone using Tapatalk
Vu+ Ultimo 4K with 3TB HDD, Dual FBC (Sat) tuners, 1x Twin Hybrid DVB-C/T/T2 tuner
Vu+ Solo 4K with 1TB HDD, Dual FBC (Sat) tuners, 1x Hybrid DVB-C/T/T2 tuner
Vu+ Solo 2 with 1TB HDD 'White Edition', 2x DVB-S2 tuners
Mut@nt HD2400 with 1TB HDD, 4x DVB-S2 tuners
Fixed 28.2E Technomate 65cm Mesh Satellite Dish with Inverto Unicable II/JESS LNB and Inverto Unicable Splitter
Fixed 28.2E Sky Zone 1 45cm Satellite Dish with Octo LNB
(All receivers installed with the latest Dev build)
Its a solo2
Vu+ Ultimo 4K with 1TB HDD, Dual FBC (Sat) tuners, 1x Twin Sat tuner. Image ViX Current
ReelBox AVG111 Sat receiver 3 x twin tuners
1 x 100cm fixed dish c/w 1 x 13°E. 1 x 19.2°E. 1 x 28.2°E. twin LNB
1 x 120cm fixed dish c/w 1 x 24.5°W. 1 x 30°W twin LNB
banjo69 (16-02-18)
No don't have 1
Hi, can I reflash the box without restoring factory settings?
Re-flashing the box will give you the default ViX image for your box.
If you've made a settings+plugins backup, you can restore them onto the image you've flashed, putting back any changes you may have made.
If you haven't a backup, then you still have a working system, but will need to start from scratch adding any changes you need.
Flashing an image is the equivalent of a factory reset.
Factory Reset is very misleading and it doesn’t mean wiping the system clean. Re-flashing the receiver and setting up as new is your best bet if you don’t want to restore any settings/plugins.
Sent from my iPhone using Tapatalk
Vu+ Ultimo 4K with 3TB HDD, Dual FBC (Sat) tuners, 1x Twin Hybrid DVB-C/T/T2 tuner
Vu+ Solo 4K with 1TB HDD, Dual FBC (Sat) tuners, 1x Hybrid DVB-C/T/T2 tuner
Vu+ Solo 2 with 1TB HDD 'White Edition', 2x DVB-S2 tuners
Mut@nt HD2400 with 1TB HDD, 4x DVB-S2 tuners
Fixed 28.2E Technomate 65cm Mesh Satellite Dish with Inverto Unicable II/JESS LNB and Inverto Unicable Splitter
Fixed 28.2E Sky Zone 1 45cm Satellite Dish with Octo LNB
(All receivers installed with the latest Dev build)
banjo69 (16-02-18)
Have you followed the flashing guide exactly as described....
http://www.openvix.co.uk/openvix-bui...Vu+%20Solo.pdf
Yea but even when I insert the mem stick and switch back on it just goes on that loop
Try a different memory stick - the smaller the better.
When I extract the downloaded file Im not getting vu, its showing solo2
That is the box you said you had.
The link is here for a VU+ Solo2.....
http://www.openvix.co.uk/index.php/d...ges/vu-solo-2/
Last edited by ccs; 16-02-18 at 16:58.
banjo69 (16-02-18)