both tuners seem to work independently, but when tuner A is recording tuner B goes blank, tuner config is set at both tuners on single sat, is this a software or hardware problem, anyone got any ideas
Does Tuner B have a direct feed from LNB?
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
yes both tuners feed seperately
how have you got your Recordings set in Recording Settings I have mine set to (preferred tuner for recording) auto that way both tuners are available
LX3 recording settings 1.jpg
Swap the feed from Tuner A and connect it to Tuner B.
Now run a Manual single satellite scan.
Menu > Setup > Service Searching > Manual Scan > Set tuner to Tuner B and set type of scan to 'Single Satellite'. You should find 960'ish channels. Test that and report back.
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
thor1 (01-09-14)
hiOriginally Posted by Sicilian
did scan on tuner A found 970 channels exactly
did scan on tuner B found 0 channels
turned tuner A off it now found 970 channels
I am aware how these receivers work I have had Dreambox 8000 for over 4yrs, its looking more and more a hardware fault
So with Tuner A disabled Tuner B found 970 channels?
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
yes same as tuner A
Not the LX3 then.
Tuner B working fine you disabled A, I'd look at LNB/Feeds/F connectors/Coax etc....
If tuners where faulty they'd find zero channels full stop.
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
for testing purposes I am using same cable
my settings are the same
so that will mean that you are also using the same LNB outlet so you should get the same result --Try the other lead and see what you get
if both tuners are selected tuner B does not work, if tuner A is turned off tuner B works
how many cables do you have connected to the LX3
two cables from sky dish
Posting Permissions
Reply With Quote
