hi all trying to get my motor working on this box i used get most sat using diseqc is it poss to use this rather than usuals if so please can you let me know thanks been trying all night joys of sats
yes it is possible infact its been known especially on teh technomate range of motors which are usuals that they work far better on diseqc
PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE
NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN! IN OPEN FORUM OR PM
IF THE POSTS HELP PLEASE CLICK THANKS OR ADD TO REP ↓
yes,...in tuner config, set it to advanced
option to use USALs, set it to no
then set it to your req position, ie; 19 east set it to 19 and so on
save
then go to positioner movement, nudge the dish east or west until you fnd the sat you are after, and save the position to ( if 19 east ) 19
but really USALs are your best option
Units; VU+Ultimo/duo/DM800/7020HD/tm9100
1.2 channel master/quad feedhorn/36volt /vbox
1 fixed dish, and 1 motorized 1mtr dish
and a pile of redundant cards/cams
thank you i will give it a go
This is the exact tutorial i used to setup my Uno with a dsieqc motor, it's the same process for all E2 receivers.
My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.
If you don't like what I post, Don't read it.
SIMPLES.
bassethound (15-12-11)
good morning thanks for your help last night managed to put in 19 e and 13e tried to add 0.w and 16 e same way this morning when i go to positioner then tune there is no new sat just 19 an 16 is it not saving when i am setting them up please help sorry people
Last edited by fizza; 15-12-11 at 07:50.
Why dont you just upload a set of engima 2 settings / bouquets and use USALS?
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
i had usuals set up before and it caused me a few issues i was getting good signals on all sats then couldnt pick up sats swithed to diseqc no issues so found it easier
Is your dish aligned correctly? If the dish is algined correctly you shouldn't have any issues provided you input your correct longitude and latitude.
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
it might be a touch out due to the bad winds up here the last week might have to get up on the roof at the weekend which what i wanted to avoid i will give it a go thanks
Sometimes you can compensate by adjusting your logitudeOriginally Posted by fizza
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
cheers for your help will give it a go
It is also important that you set the Lnb to the same number as the position ....for eg..28.2e stored position 1 set Lnb to Lnb1...then 19.2e stored pos.2 set the Lnb to Lnb2...then 16.0e stored pos.3 set the Lnb to Lnb3 and so on for each Sat. found.
hope this is of help..
rgds.Tryharder
Posting Permissions
Reply With Quote
