Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Results 1 to 1 of 1

Thread: How to flash Duolabs QBox HD Mini firmware using USB stick

  1. #1
    bassethound's Avatar
    Title
    Forum Supporter
    Donated Member
    Join Date
    May 2010
    Location
    North West
    Posts
    5,719
    Thanks
    6,871
    Thanked 6,130 Times in 2,737 Posts

    How to flash Duolabs QBox HD Mini firmware using USB stick

    How to flash Duolabs QBox HD Mini firmware using USB stick



    Items required:

    2 x USB Sticks - Formatted to FAT32 is the best option – Use HP Format Tool for formatting if you have any problems with the USB not being seen by the QBox HD Mini after formatting using Windows.

    You will normally be provided with a single 2GB USB stick with your QBox HD Mini, you will also require a second USB stick of at least 1GB to perform a firmware update (1 USB stick holds the file system and stays permanently connected to the QBox HD Mini which the other is only used when performing firmware/software updates, it can then be disconnected.


    QBox HD Mini Receiver – This guide is good for the Duolabs QBox HD Mini only

    We’ll refer to the original USB stick supplied with your receiver as (PEN1) and your second USB stick as (PEN2)

    1) Turn OFF your QBox HD Mini and remove the original USB stick (PEN1) if already connected to the receiver.

    2) Download your chosen Image file (not the Boot Image) from the forum and save it to your Windows PC. The image files will be in a .TBZ or .ZIP file for easy download.

    3) Uncompress the .TBZ or .ZIP file using WinRar or WinZip. After uncompressing the file you will find a folder called “qboxhd_update” containing the firmware update files.

    4) Insert the original (PEN1) USB stick into your PC USB port and format it (PEN1) as FAT32 with quick format option (this is the bit where you might want to use the HP format tool rather than Windows own format tool – We’ll leave that up to you to decide!).

    5) Insert the second USB stick (PEN2) into your Windows PC and format it as FAT32 with quick format option (again you might prefer to use the HP format tool to do this).

    6) Copy the “qboxhd_update” folder and its files onto the second USB stick (PEN2).

    7) Insert (PEN1) which should now be blank and formatted in FAT32 and (PEN2) which should now contain “qboxhd_update” folder and its updating files into the QBox HD Mini USB ports. It doesn't matter which ports the two USB Sticks (PEN1 and PEN2) are inserted into, you can use any of them.

    8) Turn ON the QBox HD Mini with both USB Sticks inserted and after around 15 seconds an image will appear on the screen with loading information and after around another 10 seconds the loading image will disappear and be replaced with “UPDATE IN PROGRESS “.

    9) The QBox HD Mini will now go through the process of updating the firmware and transferring between one USB stick and the other as required. Do not power off the receiver until the update is finished which can take several minutes.

    10) When the updated is finished the LCD display will tell you it’s complete and you can now turn off the QBox HD Mini and remove the second USB stick (PEN2) from the receiver, do not remove the original USB stick (PEN1) as this is what now contains your system files, without this being inserted your QBox HD Mini will fail to boot.

    11) That’s it, you have now flashed your new firmware file! Turn on the QBox HD Mini (and ensure you are connected to your local network if required) and you should now find the receiver will fully boot and take you to your start screen (which can vary depending on the firmware you loaded).

    REMEMBER IT CAN TAKE SEVERAL MINUTES TO BOOT UP FROM COLD AFTER A NEW FIRMWARE INSTALL, SO PLEASE ALLOW IT TIME TO DO SO RESISTING THE TEMPTATION TO KEEP PRESSING KEYS ON THE REMOTE CONTROL IF AT ALL POSSIBLE


    Big thanks to conchobair for the great tutorial
    All PM,s asking about c/s on cable will be ignored and reported to forum staff!

  2. The Following 6 Users Say Thank You to bassethound For This Useful Post:

    alonso (15-06-11),andy g (28-10-15),geni25 (26-09-12),Mr. Mister (15-06-11),pooface (15-06-11),punisher (15-06-11)

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.