Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Page 1 of 2 12 LastLast
Results 1 to 15 of 16

Thread: DM500HD New Hardware Drivers OE 1.6

  1. #1
    Larry-G's Avatar
    Title
    V.I.P
    Donated Member
    Join Date
    May 2010
    Posts
    32,542
    Thanks
    7,824
    Thanked 22,934 Times in 12,378 Posts

    DM500HD New Hardware Drivers OE 1.6

    01-05-2011

    - hotfix freeze after some channel changes
    - throttled mpeg decoder debug output a bit
    - fixed bcm4506 tuner crash (no hab ack messages in kernel debug)
    - fixed bcm4506 manual LDPC FEC modes
    - fixed readback of current pilot state for dvb-s2 frontends (needs a linuxtv api fix)
    - readback corrected symbolrate and frequency for bcm4501 and bcm4506
    - cxd1981 DVB-C optimizations
    My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.

    If you don't like what I post, Don't read it.

    SIMPLES.

  2. The Following 2 Users Say Thank You to Larry-G For This Useful Post:

    Donnie (02-05-11),Sicilian (02-05-11)

  3. #2
    Larry-G's Avatar
    Title
    V.I.P
    Donated Member
    Join Date
    May 2010
    Posts
    32,542
    Thanks
    7,824
    Thanked 22,934 Times in 12,378 Posts

    New Hardware Drivers DM500HD 04-05-2011

    update dm500hd,dm800se,dm8000,dm7025,dm800 hardware drivers
    - bcm4506: reintroduce minimum tune timeout of 1,5sek to fix tune failed problems caused by slow SEC switches

    WARNING
    these drivers are for original dreambox receivers only, do not attempt to flash to a cloned unit as it may cause damage.


    Code:
     
    http://sources.dreamboxupdate.com/opendreambox/1.6/dm500hd/feed-rel_31/dm500hd/dreambox-dvb-modules_2.6.18-7.4-dm500hd-20110504-r0_dm500hd.ipk
    My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.

    If you don't like what I post, Don't read it.

    SIMPLES.

  4. The Following User Says Thank You to Larry-G For This Useful Post:

    Sicilian (05-05-11)

  5. #3
    Larry-G's Avatar
    Title
    V.I.P
    Donated Member
    Join Date
    May 2010
    Posts
    32,542
    Thanks
    7,824
    Thanked 22,934 Times in 12,378 Posts

    New Hardware Drivers DM500HD 06-05-2011

    bcm4506/bcm4501 fixed broken toneburst handling (broken since 20110501 drivers)

    WARNING
    these drivers are for original dreambox receivers only, do not attempt to flash to a cloned unit as it may cause damage.



    Code:
    http://sources.dreamboxupdate.com/opendreambox/1.6/dm500hd/feed-rel_31/dm500hd/dreambox-dvb-modules_2.6.18-7.4-dm500hd-20110506-r0_dm500hd.ipk
    My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.

    If you don't like what I post, Don't read it.

    SIMPLES.

  6. The Following User Says Thank You to Larry-G For This Useful Post:

    Sicilian (10-05-11)

  7. #4

    Title
    Junior Member
    Join Date
    May 2011
    Posts
    8
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Vix on DM 500HD?

    Is it possible to install VIX on DM 500HD?

    Thx

  8. #5
    Mr. Mister's Avatar
    Title
    Moderator
    Donated Member
    Join Date
    Jul 2010
    Location
    Northern Ireland
    Posts
    4,936
    Thanks
    4,825
    Thanked 2,677 Times in 1,190 Posts
    At the moment Vix does not support Dreambox.. So no.. its not possible at the moment..

  9. #6

    Title
    Junior Member
    Join Date
    May 2011
    Posts
    8
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Quote Originally Posted by Mr. Mister View Post
    At the moment Vix does not support Dreambox.. So no.. its not possible at the moment..
    I know in VIX there is a skin where you can see the hops to the cccam server. Is there any such skin in openpli or other DM images that shows hops?

  10. #7
    Mr. Mister's Avatar
    Title
    Moderator
    Donated Member
    Join Date
    Jul 2010
    Location
    Northern Ireland
    Posts
    4,936
    Thanks
    4,825
    Thanked 2,677 Times in 1,190 Posts
    Yes.. if your talking about the hops details in the info bar..

    openpli is a good place to start..

  11. #8
    Larry-G's Avatar
    Title
    V.I.P
    Donated Member
    Join Date
    May 2010
    Posts
    32,542
    Thanks
    7,824
    Thanked 22,934 Times in 12,378 Posts
    well there is this skin for the openpli images
    http://www.world-of-satellite.com/sh...highlight=army

    note though, if you load this on to a image other than openpli it will cause a bootloop and you will have to either reflash or ftp into the box and remove the skin before it will boot properly again.
    My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.

    If you don't like what I post, Don't read it.

    SIMPLES.

  12. #9
    Larry-G's Avatar
    Title
    V.I.P
    Donated Member
    Join Date
    May 2010
    Posts
    32,542
    Thanks
    7,824
    Thanked 22,934 Times in 12,378 Posts

    DM500hd new hardware drivers 02-09-2011

    dm500hd

    update dreambox hardware drivers
    - fixed possible locking problems (deadlock)
    - fixed hybrid tuner (cxd1981) init problem,
    add possibilty for faster mode change via
    FE_SET_PROPERTY DTV_DELIVERY_SYSTEM ioctl
    - bcm4505 small typo fixed
    - better /proc/stb(vmpeg/X/dst_* handling via dst_apply

    Code:
    http://sources.dreamboxupdate.com/opendreambox/1.6/dm500hd/experimental/dm500hd/dreambox-dvb-modules_2.6.18-7.4-dm500hd-20110902-r0_dm500hd.ipk
    THESE DRIVERS ARE FOR GENUINE DREAMBOX RECEIVERS ONLY DO NOT USE ON CLONES
    My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.

    If you don't like what I post, Don't read it.

    SIMPLES.

  13. #10
    Larry-G's Avatar
    Title
    V.I.P
    Donated Member
    Join Date
    May 2010
    Posts
    32,542
    Thanks
    7,824
    Thanked 22,934 Times in 12,378 Posts
    DM500HD New Hardware Drivers 09-11-2011


    dreambox-dvb-modules.bb: update dreambox hardware drivers
    dm800/dm8000:
    - fixed sometimes inoperable hdmi audio after code change to AAC/MP3
    dm7020hd:
    - fixed bcm4505 tuner detection problems on boot from deep standby
    - fixed support for high bitrate transponders (no CI support yet)
    all:
    - dont allow to allocate a demux pid filter for fake pid 0x2000
    - fixed inoperable AUDIO button on DM7020HD remote control (dip switch depending)
    - optimized blindscan (ignore duplicate found TPs, low SR crash)
    My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.

    If you don't like what I post, Don't read it.

    SIMPLES.

  14. #11

    Title
    Junior Member
    Join Date
    Dec 2011
    Posts
    18
    Thanks
    21
    Thanked 0 Times in 0 Posts
    How to update the hardware drivers please?

  15. #12
    Larry-G's Avatar
    Title
    V.I.P
    Donated Member
    Join Date
    May 2010
    Posts
    32,542
    Thanks
    7,824
    Thanked 22,934 Times in 12,378 Posts
    02-02-2012

    update dreambox hardware drivers
    - cxd1981(hybrid DVB-C/-T) increased max. frequency to 900Mhz
    - cxd1981(hybrid DVB-T) fixed ineffective 5V for active antennas after mode change
    - bcm4505/6 improved receiption sensitivity (fixes problems with small dishes since blindscan support)
    dm500hd,dm800se,dm7020hd: fixed audio volume boost on alsa playback
    dm7020hd:
    - fixed frequently "error code 0x18006" messages on bootup
    My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.

    If you don't like what I post, Don't read it.

    SIMPLES.

  16. The Following User Says Thank You to Larry-G For This Useful Post:

    Sicilian (04-02-12)

  17. #13
    Larry-G's Avatar
    Title
    V.I.P
    Donated Member
    Join Date
    May 2010
    Posts
    32,542
    Thanks
    7,824
    Thanked 22,934 Times in 12,378 Posts
    10-02-2012

    update dm500hd hardware drivers

    - fixed strange aliasing noise on PCM Playback with needed upsampling
    - finally fixed hybrid DVB-C/-T Tuner 5V output for active antennas
    - don't fallback to DVI when the HDMI EDID was not readable
    (this fixes some HDMI audio/video problems)
    My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.

    If you don't like what I post, Don't read it.

    SIMPLES.

  18. The Following User Says Thank You to Larry-G For This Useful Post:

    Sicilian (10-02-12)

  19. #14
    Larry-G's Avatar
    Title
    V.I.P
    Donated Member
    Join Date
    May 2010
    Posts
    32,542
    Thanks
    7,824
    Thanked 22,934 Times in 12,378 Posts
    updated hardware drivers 16.02.2012

    update dm500hd, dm800se, dm8000, dm7020hd and dm800 hardware drivers

    - fixed overflow on aspect ratio calculation
    this fixes possible wrong scaled content

    - fixed scale factor calculation for dm800
    i.e. fixes wrong scaled IPTV services

    - fixed non transparent framebuffer after bootup
    this fixes not visible bootlogo before e2 starts on dm800
    My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.

    If you don't like what I post, Don't read it.

    SIMPLES.

  20. The Following User Says Thank You to Larry-G For This Useful Post:

    Sicilian (23-03-12)

  21. #15
    Larry-G's Avatar
    Title
    V.I.P
    Donated Member
    Join Date
    May 2010
    Posts
    32,542
    Thanks
    7,824
    Thanked 22,934 Times in 12,378 Posts
    update dreambox hardware modules for dm500hd, dm800se, dm7020hd, dm8000

    reverted: "fixed strange aliasing noise on PCM Playback with needed upsampling" change from 20120210 drivers
    My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.

    If you don't like what I post, Don't read it.

    SIMPLES.

  22. The Following User Says Thank You to Larry-G For This Useful Post:

    Sicilian (23-03-12)

Page 1 of 2 12 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.