OpenViX 6.3 Released! Support/discussion thread

[stash36]

Ah ok, I'll reach out. Thank you.

[malcolmp]

Probably not the correct way to do it but a hack till a solution is found

Please make a backup incase of issues

This is from vuuno4k feeds but it's an all ipk so may work

opkg install http://www.openvix.co.uk/feeds/openvix/release/6.3/vuuno4k/all/openresolv_3.7.3-r0_all.ipk

Put VPN manager ipk in tmp then

opkg install /tmp/*.ipk

See if that works

Hi.

Openvix 6.3.002, Gigablue UHD UE 4K here.
a
Just to confirm installed instructions above, and VPN Manager and OpenVPN is working OK for with PureVPN, thanks.

[Zdrudge]

I'm currently running v6.0.008. The instructions don't indicate if it's possible to update directly to the latest version. Is it? I tried today and it didn't go well, so I reverted to the previous version.

I had difficulty with the plugins: CrossEPG Downloader, EPG-Importer, IMDb search, IMDb setup, Media Scanner, OpenWebif, Picture player installed.

The python script for listing plugins* didn't run (the script needed parentheses added to the print commands), then when it did run it didn't produce any output. I couldn't see that CrossEPG Downloader was available for installation and stopped at that point.

*Step 8 here: https://www.world-of-satellite.com/s...p-and-Restores

Any advice? Thanks

[Zdrudge]

I forgot to mention: I'm using a Zgemma H7S.

[Willo3092]

You should be fine doing a settings backup and restore to the new image.
If you flash ViX 6.3.003 to a different partition using image manager you will be able to boot back into your existing image if it goes wrong.

I think the pluginslist.py script is python 2 so probably won't work now.

[abu baniaz]

There is no need for you to backup things manually. That section was there a long time ago when some things were not compatible. I will edit it, to make it clearer.

As above, a settings backup (as a default, this is done when you perform a software update or flash using Image Manager)
You can't perform a software update, you must install/flash 6.3. You don't have to go through the image numbers, flash most recent one.

You can install CrossEPG downloader if you want.

[gooner690]

I have a WiFi card in the back of my TM nano M3. I have installed the RTL8192CU driver then unplugged the ethernet cable and rebooted the box but I cannot choose my WiFi device as there is no network adapters menu anywhere for me to do so. Therefore I cannot run my box off the WiFi but only through the LAN cable. Please can you correct this?

[nunigaia]

OpenVix 6.3.004 ( release ) and with OpenBh 5.2.004 ( release ) - issue.

I have open an issue under openvix git enigma2 section --> https://github.com/OpenViX/enigma2/issues/863

Anyone from dev´s can take a look to it, please?

best regards
nunigaia

[nunigaia]

OpenVix 6.3.004 ( release ) and with OpenBh 5.2.004 ( release ) - issue.

I have open an issue under openvix git enigma2 section --> https://github.com/OpenViX/enigma2/issues/863

Anyone from dev´s can take a look to it, please?

best regards
nunigaia

It should be fixed after this commit! ( Just tested it now ( after updating image ) running OpenBh 5.2.004 with the lastest update )

So, I will close the issue opened! https://github.com/OpenViX/enigma2/issues/863

thanks @Huevos and @Dimitarcc for the fix!

best regards
nunigaia