Thanks ccs, much appreciated. I want to use OpenVix but it is too challenging until this is sorted.
If anyone wants more data, please just ask.
Geoff
Thanks ccs, much appreciated. I want to use OpenVix but it is too challenging until this is sorted.
If anyone wants more data, please just ask.
Geoff
Geoff
**********************************************
Gigablue UHD UE 4K receiver
GigaBlue Ultra Unicable SCR-LNB / 24 SCR - 2 Legacy UHD 4K LNB
OpenVix 6.0.007 Image
110cms Triax Dish
**********************************************
Updated 04/02/2022
Geoff all your posts are seen by developers.I know that it is difficult learning from scratch and therefore we would like to support you as best as we can..... but also accept that this all done during our free time, this is not paid work.
@ccs has suggested that you do a clean flash with OpenViX, which is what you have done with OpenATV, could you do that and then feedback?
.
I would suggest that you have been on a learning curve with OpenViX and there may be an issue caused by that. The logs show that the software is trying to recover from errors on the recording and then spends time skipping through - I am not able to see if you initiated that or whether that's part of the recovery issue.
I have as my lounge receiver a gbquad4k(basically same as the gbue4k which I also have) and have never seen these issues during the last 4 years (and I am guessing my configuration is similar in terms of recordings), so this is not a typical issue and that's why I would suggest a new flash and setup.
Gigablue Quad 4K & UE 4K
.........FBC Tuners:
------------------> GT-Sat unicable LNB to 1.5M dish(28.2E)
------------------> Gigablue unicable LNB to 80 cm dish(19.2E)
.......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using unicable ports
Zgemma H9 C/S into Giga4K
GeoffatMM (07-02-22)
Thanks Twol,
I really appreciate your comments.
I do understand there is no paid developer team and I am not complaining just trying to ensure the feedback is picked up.
I too am pretty busy building a house so the time I can devote to sorting this (which is the system for the new house when we move in) is also limited.
I did initially try reflashing but then imported ils settings and plugins.
Now that the receiver is stable using OpenATV I will do as ccs suggests and prepare a fresh install then rebuild from that as I assume using old settings and plugins have just imported the same problem.
It will take a few days but I will post results back here.
Geoff
Sent from my iPhone using Tapatalk
Geoff
**********************************************
Gigablue UHD UE 4K receiver
GigaBlue Ultra Unicable SCR-LNB / 24 SCR - 2 Legacy UHD 4K LNB
OpenVix 6.0.007 Image
110cms Triax Dish
**********************************************
Updated 04/02/2022
Hi,
Just an update to finish this post off.
I have cleaned down the machine and flashed it from a USB to make a clean install then entered all the settings. The only thing I have not done is install the Kodi plugin. Since then it has been behaving itself so perhaps it is now cured and this can be closed.
Geoff
Geoff
**********************************************
Gigablue UHD UE 4K receiver
GigaBlue Ultra Unicable SCR-LNB / 24 SCR - 2 Legacy UHD 4K LNB
OpenVix 6.0.007 Image
110cms Triax Dish
**********************************************
Updated 04/02/2022