Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Results 1 to 7 of 7

Thread: Deep standby causing iptv to fail

  1. #1

    Title
    Junior Member
    Join Date
    Nov 2015
    Posts
    5
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Deep standby causing iptv to fail

    Hi, got a strange problem when the box awakes from deep standby, basically all Iptv channels are black screen with message no data on the transponder.
    If I flick the power switch off on everything works as expected.
    Any ideas or thoughts would be welcome.
    Thanks

  2. #2
    Andy_Hazza's Avatar
    Title
    Moderator
    Join Date
    Oct 2012
    Location
    Derbyshire, UK
    Posts
    7,287
    Thanks
    2,855
    Thanked 2,126 Times in 1,752 Posts
    Flicking the power switch on/off is just asking for trouble. Personally just put into standby mode, as IPTV relies heavily on your internet/network and I’m guessing going into deep standby affects the network thus why you are getting blankety blanks when coming out of deep standby.
    I maybe wrong though, but thats my theory on it.


    Sent from my iPhone using Tapatalk
    Vu+ Ultimo 4K with 3TB HDD, Dual FBC (Sat) tuners, 1x Twin Hybrid DVB-C/T/T2 tuner
    Vu+ Solo 4K with 1TB HDD, Dual FBC (Sat) tuners, 1x Hybrid DVB-C/T/T2 tuner
    Vu+ Solo 2 with 1TB HDD 'White Edition', 2x DVB-S2 tuners
    Mut@nt HD2400 with 1TB HDD, 4x DVB-S2 tuners
    Fixed 28.2E Technomate 65cm Mesh Satellite Dish with Inverto Unicable II/JESS LNB and Inverto Unicable Splitter
    Fixed 28.2E Sky Zone 1 45cm Satellite Dish with Octo LNB
    (All receivers installed with the latest Dev build)

  3. #3

    Title
    Junior Member
    Join Date
    Nov 2015
    Posts
    5
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Hey, thanks for reply.
    It’s possible I guess but the network test comes up green plus I’m sure I’ve had this working in the past.
    I don’t actually use the box very often so deep standby was my preferred option.
    Perhaps I’ll try the WiFi connection instead and see if same happens.

  4. #4

    Title
    Forum Supporter
    Donated Member
    Join Date
    Jun 2010
    Posts
    3,007
    Thanks
    1,347
    Thanked 427 Times in 391 Posts
    I would imagine cable is always better than wifi,have you tried restart Gui or reboot?

  5. #5

    Title
    Junior Member
    Join Date
    Nov 2015
    Posts
    5
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Yeah, WiFi same as wired. Reboot still doesn’t work. It needs a power cycle to start working again.
    If I upload the bouquets again it works without the need for the on/off.
    Weird.
    Last edited by Markle; 03-04-19 at 21:20.

  6. #6
    Andy_Hazza's Avatar
    Title
    Moderator
    Join Date
    Oct 2012
    Location
    Derbyshire, UK
    Posts
    7,287
    Thanks
    2,855
    Thanked 2,126 Times in 1,752 Posts
    I think personally you will need to set a timer to bring your receiver out of deep standby, then see if you can then run an IPTV Bouquet scan then put your receiver into standby mode and see if that works.


    Sent from my iPhone using Tapatalk
    Vu+ Ultimo 4K with 3TB HDD, Dual FBC (Sat) tuners, 1x Twin Hybrid DVB-C/T/T2 tuner
    Vu+ Solo 4K with 1TB HDD, Dual FBC (Sat) tuners, 1x Hybrid DVB-C/T/T2 tuner
    Vu+ Solo 2 with 1TB HDD 'White Edition', 2x DVB-S2 tuners
    Mut@nt HD2400 with 1TB HDD, 4x DVB-S2 tuners
    Fixed 28.2E Technomate 65cm Mesh Satellite Dish with Inverto Unicable II/JESS LNB and Inverto Unicable Splitter
    Fixed 28.2E Sky Zone 1 45cm Satellite Dish with Octo LNB
    (All receivers installed with the latest Dev build)

  7. #7

    Title
    Junior Member
    Join Date
    Nov 2015
    Posts
    5
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Hi, appreciate the support on this one. It’s doing my head in.
    Not sure how bringing the box out of deep standby with a timer would make any difference but I’ll give it a go.
    The bouquets were uploaded using echannelizer via an iptv provider. All the existing ones work fine.
    Definitely not a network issue because as I’ve said if I re upload the bouquet it works without the need for a power cycle,
    Thanks again anyway.

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.