Results 1 to 4 of 4
  1. #1
    Moderator abu baniaz's Avatar

    Join Date
    Sep 2010
    Location
    East London
    Posts
    18,733
    Thanks
    4,914
    Thanked 7,317 Times in 4,936 Posts

    GT-Sat GT-dLNB1DY and tuner configuration

    Below is a guide for configuring the GT-sat Unicable LNB with FBC tuners with only one wire and no splitters
    ABM and CrossEPG require sole control of a Tuner, so you will get blackouts while they run.

    (As a reminder, FBC tuners and Unicable are two separate technologies.
    You can use Unicable LNBs with non-FBC tuners. Eg Dreambox 500, Vu Solo 2, Technomate Nano 3t combo
    You can use an FBC tuner with universal (normal) LNBs.
    FBC with unicable offers more than FBC with universal.)

    For this guide, the setup is a unicable LNB with a single signal/co-axial wire connected to Tuner A. Ensure you attach the signal/coaxial wire to the correct tuner.
    You can use tuner B if you wish, it does not matter which you use. Just make sure you select the right one

    Physical setup is as pictured.

    unicable multi tuner_unused tuner.jpg


    The GT-Sat GT-dLNB1DY and GT-Sat GT-S3DCSS24 can use the generic name of dLNB Hello

    Tuner A

    gtsat fbc tuner a_1 .jpg

    Tuner A

    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 1 (0975)
    Connected: No
    DiSEqC mode: None
    Force legacy signal stats: No

    Tuner B

    gtsat fbc tuner b_1 .jpg

    Tuner B

    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 2 (1025)
    Connected: Yes
    Connected to: Tuner A (Tuner A is one with the signal wire attached to it)
    DiSEqC mode: None
    Force legacy signal stats: No

    Tuner C
    gtsat fbc tuner c_1 .jpg

    Tuner C

    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 3 (1075)
    Connected: Yes
    Connected to: Tuner A (Tuner A is one with the signal wire attached to it)
    DiSEqC mode: None
    Force legacy signal stats: No


    Tuner D

    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 4 (1125)
    Connected: Yes
    Connected to: Tuner A (Tuner A is one with the signal wire attached to it)
    DiSEqC mode: None
    Force legacy signal stats: No


    Tuner E

    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 5 (1175)
    Connected: Yes
    Connected to: Tuner A (Tuner A is one with the signal wire attached to it)
    DiSEqC mode: None
    Force legacy signal stats: No


    Tuner F

    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 6 (1225)
    Connected: Yes
    Connected to: Tuner A (Tuner A is one with the signal wire attached to it)
    DiSEqC mode: None
    Force legacy signal stats: No


    Tuner G

    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 7 (1275)
    Connected: Yes
    Connected to: Tuner A (Tuner A is one with the signal wire attached to it)
    DiSEqC mode: None
    Force legacy signal stats: No


    Tuner H

    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 8 (1325)
    Connected: Yes
    Connected to: Tuner A (Tuner A is one with the signal wire attached to it)
    DiSEqC mode: None
    Force legacy signal stats: No



    Note:
    Every tuner on all devices connected to the LNB must have a separate user band number. Even if on a different receiver.
    The above has used user band/channel/ numbers starting from 1. If you have more than one receiver, start at 9. If you run out of user bands, select FBC automatic for some tuners, this will be an enhanced loop through mode.

  2. The Following 3 Users Say Thank You to abu baniaz For This Useful Post:

    rebeve (31-03-19),Sicilian (30-12-18),Willo3092 (19-01-19)

  3. #2
    Moderator abu baniaz's Avatar

    Join Date
    Sep 2010
    Location
    East London
    Posts
    18,733
    Thanks
    4,914
    Thanked 7,317 Times in 4,936 Posts

    GT-Sat GT-dLNB1DY and FBC tuner configuration

    Below is a guide for configuring the GT-sat Unicable LNB with FBC tuners with splitters to provide both tuners

    (As a reminder, FBC tuners and Unicable are two separate technologies.
    You can use Unicable LNBs with non-FBC tuners. Eg Dreambox 500, Vu Solo 2, Technomate Nano 3t combo
    You can use an FBC tuner with universal (normal) LNBs.
    FBC with unicable offers more than FBC with universal.)

    For this guide, the setup is a unicable LNB. A splitter is used to supply signal to Tuner A and Tuner B.

    Physical setup is as pictured.
    unicable diseqc multi receivers_2_2_2.jpg



    The GT-Sat GT-dLNB1DY and GT-Sat GT-S3DCSS24 can use the generic name of dLNB Hello

    Tuner A

    gtsat fbc tuner a_1 .jpg

    Tuner A

    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 1 (0975)
    Connected: No
    DiSEqC mode: None
    Force legacy signal stats: No

    Tuner B
    gtsat fbc tuner b_2 .jpg

    As this has a signal wire attached, we must set connected to "no".
    Tuner B

    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 2 (1025)
    Connected: No
    DiSEqC mode: None
    Force legacy signal stats: No

    Tuner C
    gtsat fbc tuner c_1 .jpg

    Tuner C

    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 3 (1075)
    Connected: Yes
    Connected to: Tuner A (Tuner A is one with the signal wire attached to it)
    DiSEqC mode: None
    Force legacy signal stats: No


    Tuner D

    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 4 (1125)
    Connected: Yes
    Connected to: Tuner A (Tuner A is one with the signal wire attached to it)
    DiSEqC mode: None
    Force legacy signal stats: No


    Tuner E

    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 5 (1175)
    Connected: Yes
    Connected to: Tuner A (Tuner A is one with the signal wire attached to it)
    DiSEqC mode: None
    Force legacy signal stats: No


    Tuner F

    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 6 (1225)
    Connected: Yes
    Connected to: Tuner A (Tuner A is one with the signal wire attached to it)
    DiSEqC mode: None
    Force legacy signal stats: No


    Tuner G

    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 7 (1275)
    Connected: Yes
    Connected to: Tuner A (Tuner A is one with the signal wire attached to it)
    DiSEqC mode: None
    Force legacy signal stats: No


    Tuner H

    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 8 (1325)
    Connected: Yes
    Connected to: Tuner A (Tuner A is one with the signal wire attached to it)
    DiSEqC mode: None
    Force legacy signal stats: No


    Note:
    Every tuner on all devices connected to the LNB must have a separate user band number. Even if on a different receiver.
    The above has used user band/channel/ numbers starting from 1. If you have more than one receiver, start at 9. If you run out of user bands, select FBC automatic for some tuners, this will be an enhanced loop through mode.
    Attached Images Attached Images

  4. The Following 3 Users Say Thank You to abu baniaz For This Useful Post:

    Sicilian (30-12-18),Toja60 (04-03-19),Willo3092 (19-01-19)

  5. #3
    Moderator abu baniaz's Avatar

    Join Date
    Sep 2010
    Location
    East London
    Posts
    18,733
    Thanks
    4,914
    Thanked 7,317 Times in 4,936 Posts
    GT-Sat GT-dLNB1DY and standard tuner configuration

    Below is a guide for configuring the GT-sat Unicable LNB with standard/non-fbc tuners. Splitter used to provide all tuners with signal

    (As a reminder, FBC tuners and Unicable are two separate technologies.
    You can use Unicable LNBs with non-FBC tuners. Eg Dreambox 500, Vu Solo 2, Technomate Nano 3t combo
    You can use an FBC tuner with universal (normal) LNBs.
    FBC with unicable offers more than FBC with universal.)

    The setup is a unicable LNB supplying more than one receiver with the use of splitters. This post is specific to non-FBC tuners. As user bands 1-8 are in use with one receiver, 9-16 with another, we will be starting from 17.

    Setup is as pictured:
    unicable multi receivers_2_2.jpg


    Tuner A
    tm 3t a.jpg

    Tuner A

    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 17 (1775)
    Connected: No
    DiSEqC mode: None
    Force legacy signal stats: No

    Tuner B
    tm 3t b.jpg

    Tuner B

    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 18 (1825)
    Connected: No
    DiSEqC mode: None
    Force legacy signal stats: No

  6. The Following 2 Users Say Thank You to abu baniaz For This Useful Post:

    Sicilian (30-12-18),Willo3092 (19-01-19)

  7. #4
    Moderator abu baniaz's Avatar

    Join Date
    Sep 2010
    Location
    East London
    Posts
    18,733
    Thanks
    4,914
    Thanked 7,317 Times in 4,936 Posts
    GT-Sat GT-dLNB1DY and standard tuner internal connection


    Receivers with BCM 7356 such as Vu Solo 2, Technomate Nano 2 super/3T combo, Gigablue quad plus have internally connected tuners. The condition to use this on these receivers is that the signal wire must be attached to tuner B, not Tuner A. Once again, if you want to use internal connection on 7356 SOC receivers, do not connect to Tuner A. This applies to both Unicable as well as Universal LNBs.

    It is better for you to get a splitter and use it for both tuners. However the facility is there, so documenting it for those who need it.

    Picture of setup is as below.
    unicable multi tuner_tuner - 7356.jpg

    As signal wire is attached to Tuner B, lets do that first.

    Tuner B
    tm 3t b2.jpg

    Tuner B


    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 19 (1875)
    Connected: No
    DiSEqC mode: None
    Force legacy signal stats: No


    Tuner A
    7356_a.jpg

    Tuner A


    Configuration mode: Advanced
    Satellite: 28.2E
    LNB: LNB 1
    Priority: Auto
    Type of LNB/Device: SCR(Unicable/Jess)
    SCR (Unicable/JESS) type: LNB
    Manufacturer: GT-Sat
    Model: dLNB dHello
    Channel: Userband 20 (1925)
    Connected: Yes
    Connected to: Tuner B (Tuner B is one with the signal wire attached to it)
    DiSEqC mode: None
    Force legacy signal stats: No


    Note:
    If you are using any other tuner with internal connection, process is the same. Just make sure you connect to the correct tuner. As an example a twin tuner card on the Duo 2 is internally connected.

  8. The Following 4 Users Say Thank You to abu baniaz For This Useful Post:

    gravedigger59 (30-12-18),John57 (31-12-18),Sicilian (30-12-18),Willo3092 (30-12-18)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.