Dreambox Control Center - Connection problem

[nekrub2]

Dear all

Until yesterday I could use dreambox control center to have have access to my vu+solo2 image (and USB music store). However, when trying to connect DCC I get the following messages:

Checking network...
Telnet Connected
Connection failed!

It looks as if I had changed the username or the password. I thought I would still have the default values.

Strange enough WebIF works and I can make screenshots.

I have tried to restore the setting from 20 November, but it did not help.

Any clue how I could get DCC FTP up and running again?

Thanks for your hints
nekrub2

[^^COMPASS^^]

If you aren't using DCC version 1.41, i would give it a go

[timofee]

You could try right click, run as administrator.

There is a new DCC v2 version out. You could that as a fresh install to see if it flushes out the problem.

[nekrub2]

Sorry did not work with running as admin.

Attach screenshot.

Error_DCC_V2.JPG


Must have something to do with the password. Will try to fiddle round.

Tough luck - thanks anyway
nekrub2

[ccs]

Which username and password does OpenWebif work with?

[nekrub2]

Hi

In the OpenwebIF Configuration I set the HTTP port to 00080 and the HTTP Authentication to no. I think with this setting it does not test the password.

Best regard
nekrub2

[abu baniaz]

Which version of DCC are you using? There was another update to DCC today to fix a connection problem.

[nekrub2]

Hi Abu

I orginially had V2.95 but installed today DCC-E2. On both of them I have the same trouble.

I heard that there will be a new V2 version soon. I will also try this one.

I wouldn't like to flash my box and building up everything from scratch. I'm scared that I will lose my MP3player database and cache files.

Best regards
nekrub2

[Andy_Hazza]

Try something like Filezilla or FlashFXP for your ftp needs and something like PuTty for your telnet needs.


Sent from my iPhone using Tapatalk

[nekrub2]

Hi Andy

Tough luck: On Fizilla the same
Status: Connecting to 192.168.1.102:21...
Status: Connection attempt failed with "ECONNREFUSED - Connection refused by server".
Error: Could not connect to server
Status: Waiting to retry...
Status: Connecting to 192.168.1.102:21...
Status: Connection attempt failed with "ECONNREFUSED - Connection refused by server".
Error: Could not connect to server

It looks as if I had blocked my box from connecting to FTP. Do you know which settings I might have altered by error?
In the worst case remains only system flash with USB without reloading of anny settings.
Best regards
nekrub2

[adm]

Hi Andy

Tough luck: On Fizilla the same
Status: Connecting to 192.168.1.102:21...
Status: Connection attempt failed with "ECONNREFUSED - Connection refused by server".
Error: Could not connect to server
Status: Waiting to retry...
Status: Connecting to 192.168.1.102:21...
Status: Connection attempt failed with "ECONNREFUSED - Connection refused by server".
Error: Could not connect to server

It looks as if I had blocked my box from connecting to FTP. Do you know which settings I might have altered by error?
In the worst case remains only system flash with USB without reloading of anny settings.
Best regards
nekrub2

You get that message if FTP is not running on your box

Menu -> Setup -> Network -> Utilities -> Utilities

If the current status says stopped press geen to start it
Also enable autostart in the same screen

[nekrub2]

Dear adm

As you suggested I have gone to Setup/ Network/Utilities/FTP and found that autostart is enabled but the current status is stopped.

However, clicking on the green botton did not start it. This is nasty. Does this mean that I have to reload the image via USB and do all the settings manually on the box?

Thanks for your help
nekrub2

[adm]

Dear adm

As you suggested I have gone to Setup/ Network/Utilities/FTP and found that autostart is enabled but the current status is stopped.

However, clicking on the green botton did not start it. This is nasty. Does this mean that I have to reload the image via USB and do all the settings manually on the box?

Thanks for your help
nekrub2

Have you tried turning off at the mains plug (after first putting the box into deep standby) and leaving the box off for 60 seconds to let all internal power supply lines discharge before switching back on? Sometimes this complete cold boot can cure problems, especially after an image update.

[birdman]

However, clicking on the green botton did not start it. This is nasty. Does this mean that I have to reload the image via USB and do all the settings manually on the box?

I reckon looking at the debug log would be more likely to produce a result.
Although you'd probably do that via FTP, s a bit chicken-and-eggy...

You can look at the debug log from the Vix menu system:

Menu -> System -> Logs -> Log manager, ensure you are in Debug logs then View the chosen log.

[ccs]

Maybe menu/setup/network/password