Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Page 1 of 2 12 LastLast
Results 1 to 15 of 21

Thread: Dreambox Control Center - Connection problem

  1. #1

    Title
    Senior Member
    Join Date
    Dec 2015
    Location
    Switzerland
    Posts
    307
    Thanks
    63
    Thanked 52 Times in 43 Posts

    Dreambox Control Center - Connection problem

    Dear all

    Until yesterday I could use dreambox control center to have have access to my vu+solo2 image (and USB music store). However, when trying to connect DCC I get the following messages:

    Checking network...
    Telnet Connected
    Connection failed!

    It looks as if I had changed the username or the password. I thought I would still have the default values.

    Strange enough WebIF works and I can make screenshots.

    I have tried to restore the setting from 20 November, but it did not help.

    Any clue how I could get DCC FTP up and running again?

    Thanks for your hints
    nekrub2
    VU+ Solo2
    USB 32GB used as HDD
    Diseq 13.0E 19.0E

  2. #2
    ^^COMPASS^^'s Avatar
    Title
    Forum Supporter
    Donated Member
    Join Date
    Dec 2011
    Posts
    268
    Thanks
    281
    Thanked 307 Times in 125 Posts
    If you aren't using DCC version 1.41, i would give it a go

    Vu+UNO 4K SE [OE-Alliance-4.4 Firmware 5.4-010-Build Oscam-r11693-798][with keys]
    Vu+DUO 2 [OE-Alliance-4.4 Firmware 5.4-003-Build Oscam-r11572-798][with keys]
    Vu+SOLO 2 [OE-Alliance-4.3 Firmware 5.3-039-Build MGcamd]
    Vu+SOLO SE [OE-Alliance-4.4 Firmware 5.4-003-Build MGcamd]

  3. #3

    Title
    Senior Member
    Join Date
    Jan 2014
    Posts
    589
    Thanks
    56
    Thanked 118 Times in 104 Posts
    You could try right click, run as administrator.

    There is a new DCC v2 version out. You could that as a fresh install to see if it flushes out the problem.

  4. #4

    Title
    Senior Member
    Join Date
    Dec 2015
    Location
    Switzerland
    Posts
    307
    Thanks
    63
    Thanked 52 Times in 43 Posts

    DCC connection error

    Sorry did not work with running as admin.

    Attach screenshot.

    Error_DCC_V2.JPG


    Must have something to do with the password. Will try to fiddle round.

    Tough luck - thanks anyway
    nekrub2
    VU+ Solo2
    USB 32GB used as HDD
    Diseq 13.0E 19.0E

  5. #5
    ccs's Avatar
    Title
    ViX Beta Tester
    Join Date
    Sep 2014
    Posts
    5,836
    Thanks
    554
    Thanked 1,276 Times in 1,089 Posts
    Which username and password does OpenWebif work with?

  6. #6

    Title
    Senior Member
    Join Date
    Dec 2015
    Location
    Switzerland
    Posts
    307
    Thanks
    63
    Thanked 52 Times in 43 Posts

    OpenwebIF connection

    Hi

    In the OpenwebIF Configuration I set the HTTP port to 00080 and the HTTP Authentication to no. I think with this setting it does not test the password.

    Best regard
    nekrub2
    VU+ Solo2
    USB 32GB used as HDD
    Diseq 13.0E 19.0E

  7. #7
    abu baniaz's Avatar
    Title
    Moderator
    Join Date
    Sep 2010
    Location
    East London
    Posts
    23,335
    Thanks
    6,421
    Thanked 9,146 Times in 6,224 Posts
    Which version of DCC are you using? There was another update to DCC today to fix a connection problem.

  8. #8

    Title
    Senior Member
    Join Date
    Dec 2015
    Location
    Switzerland
    Posts
    307
    Thanks
    63
    Thanked 52 Times in 43 Posts

    DCC Version

    Hi Abu

    I orginially had V2.95 but installed today DCC-E2. On both of them I have the same trouble.

    I heard that there will be a new V2 version soon. I will also try this one.

    I wouldn't like to flash my box and building up everything from scratch. I'm scared that I will lose my MP3player database and cache files.

    Best regards
    nekrub2
    VU+ Solo2
    USB 32GB used as HDD
    Diseq 13.0E 19.0E

  9. #9
    Andy_Hazza's Avatar
    Title
    Moderator
    Join Date
    Oct 2012
    Location
    Derbyshire, UK
    Posts
    7,287
    Thanks
    2,855
    Thanked 2,126 Times in 1,752 Posts

    Dreambox Control Center - Connection problem

    Try something like Filezilla or FlashFXP for your ftp needs and something like PuTty for your telnet needs.


    Sent from my iPhone using Tapatalk
    Last edited by Andy_Hazza; 28-11-18 at 05:57.
    Vu+ Ultimo 4K with 3TB HDD, Dual FBC (Sat) tuners, 1x Twin Hybrid DVB-C/T/T2 tuner
    Vu+ Solo 4K with 1TB HDD, Dual FBC (Sat) tuners, 1x Hybrid DVB-C/T/T2 tuner
    Vu+ Solo 2 with 1TB HDD 'White Edition', 2x DVB-S2 tuners
    Mut@nt HD2400 with 1TB HDD, 4x DVB-S2 tuners
    Fixed 28.2E Technomate 65cm Mesh Satellite Dish with Inverto Unicable II/JESS LNB and Inverto Unicable Splitter
    Fixed 28.2E Sky Zone 1 45cm Satellite Dish with Octo LNB
    (All receivers installed with the latest Dev build)

  10. The Following User Says Thank You to Andy_Hazza For This Useful Post:

    nekrub2 (28-11-18)

  11. #10

    Title
    Senior Member
    Join Date
    Dec 2015
    Location
    Switzerland
    Posts
    307
    Thanks
    63
    Thanked 52 Times in 43 Posts
    Hi Andy

    Tough luck: On Fizilla the same
    Status: Connecting to 192.168.1.102:21...
    Status: Connection attempt failed with "ECONNREFUSED - Connection refused by server".
    Error: Could not connect to server
    Status: Waiting to retry...
    Status: Connecting to 192.168.1.102:21...
    Status: Connection attempt failed with "ECONNREFUSED - Connection refused by server".
    Error: Could not connect to server

    It looks as if I had blocked my box from connecting to FTP. Do you know which settings I might have altered by error?
    In the worst case remains only system flash with USB without reloading of anny settings.
    Best regards
    nekrub2
    VU+ Solo2
    USB 32GB used as HDD
    Diseq 13.0E 19.0E

  12. #11
    ccs's Avatar
    Title
    ViX Beta Tester
    Join Date
    Sep 2014
    Posts
    5,836
    Thanks
    554
    Thanked 1,276 Times in 1,089 Posts
    Maybe menu/setup/network/password

  13. #12

    Title
    Senior Member
    Join Date
    Dec 2015
    Location
    Switzerland
    Posts
    307
    Thanks
    63
    Thanked 52 Times in 43 Posts

    Setup / Network / Password

    Sorry did not help.
    VU+ Solo2
    USB 32GB used as HDD
    Diseq 13.0E 19.0E

  14. #13
    wullboy's Avatar
    Title
    V.I.P
    Donated Member
    Join Date
    Mar 2010
    Location
    North of you
    Posts
    797
    Thanks
    147
    Thanked 147 Times in 116 Posts
    Re-boot both router then box, get new ip address from box, then try to FTP in again, see if it connects
    What else can i say !!.....


    You can`t please all of the people all of the time...so...dont even try........ ...


    Code:
    http://www.youtube.com/watch?v=dugJTYz-JR4&feature=em-subs_digest


  15. #14

    Title
    Senior Member
    Join Date
    Dec 2015
    Location
    Switzerland
    Posts
    307
    Thanks
    63
    Thanked 52 Times in 43 Posts
    Hi wollboy

    Nice try - but no cigar. Did as suggested by you but did not help. Openif on port 80 (without request for login) works. However FTP does not.
    This is what I get from FileZilla when using instead of FTP:// IP FTPS://

    Status: Waiting to retry...
    Status: Connecting to 192.168.1.102:21...
    Response: fzSftp started, protocol_version=8
    Command: open "root@192.168.1.102" 21
    Error: Network error: Connection refused
    Error: Could not connect to server

    So there is a repose but the connection is refused.
    VU+ Solo2
    USB 32GB used as HDD
    Diseq 13.0E 19.0E

  16. #15
    adm's Avatar
    Title
    Forum Supporter
    Donated Member
    Join Date
    Sep 2014
    Location
    Southend on Sea, UK
    Posts
    1,636
    Thanks
    62
    Thanked 647 Times in 505 Posts
    Quote Originally Posted by nekrub2 View Post
    Hi Andy

    Tough luck: On Fizilla the same
    Status: Connecting to 192.168.1.102:21...
    Status: Connection attempt failed with "ECONNREFUSED - Connection refused by server".
    Error: Could not connect to server
    Status: Waiting to retry...
    Status: Connecting to 192.168.1.102:21...
    Status: Connection attempt failed with "ECONNREFUSED - Connection refused by server".
    Error: Could not connect to server

    It looks as if I had blocked my box from connecting to FTP. Do you know which settings I might have altered by error?
    In the worst case remains only system flash with USB without reloading of anny settings.
    Best regards
    nekrub2
    You get that message if FTP is not running on your box

    Menu -> Setup -> Network -> Utilities -> Utilities

    If the current status says stopped press geen to start it
    Also enable autostart in the same screen
    Xtrend ET10K, 2 x satellite tuners 28.2 (Sky FTA), 2 x hybrid (UK Freeview), Zgemma H9S (satellite)

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.