Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Results 1 to 11 of 11

Thread: Client mode problem

  1. #1
    TK4|2|1's Avatar
    Title
    Senior Member
    Join Date
    May 2011
    Location
    If there's a bright centre to the universe, I'm from the planet that is farthest from.
    Posts
    940
    Thanks
    228
    Thanked 180 Times in 159 Posts

    Client mode problem

    Hi all,
    For about a year I've been RCSC without any issue, so when I got a zero, to replace my wetek (running openATV), I thought I'd give client mode a go.
    My server box is a Technomate 2T. Both boxes running 5.0.23
    The problem I'm having is, when I select a subscription channel (yes I have a card) on the client, I get no picture. If I come down stairs and select the same channel on the server box, no picture. If I restart Oscam, both boxes will start working.
    I thought it may be client mode, so I installed RCSC onto the zero, but the same happens.
    I can watch the technomate all day without a problem, it's only once I've started up the zero in the bedroom.
    Can anybody suggest what might be causing it? As I say, before I got the zero, it was flawless on the wetek using RCSC.


    Sent from my iPad using Tapatalk

  2. #2
    Sicilian's Avatar
    Title
    The Boss
    Join Date
    Mar 2010
    Posts
    29,645
    Thanks
    23,575
    Thanked 26,044 Times in 7,633 Posts
    Sounds like Oscam is crashing on the Tm-2T. Possibly the Zero crashing the 2T. Have you checked the oscam logs?
    D I S C L A I M E R

    My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!

    Follow us on Twitter 0penViX
    Rules can be found
    HERE
    Support our sponsor World-Of-Satellite
    HERE
    GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
    Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable





  3. #3
    TK4|2|1's Avatar
    Title
    Senior Member
    Join Date
    May 2011
    Location
    If there's a bright centre to the universe, I'm from the planet that is farthest from.
    Posts
    940
    Thanks
    228
    Thanked 180 Times in 159 Posts
    I'll take a look, but not sure what I'm looking for.

  4. #4
    twol's Avatar
    Title
    Moderator
    Join Date
    Apr 2012
    Posts
    8,382
    Thanks
    987
    Thanked 2,888 Times in 2,243 Posts
    Can you show the tuner config on both boxes?
    Gigablue Quad 4K & UE 4K
    .........FBC Tuners:
    ------------------> DUR-Line DCR 5-1-8-L4 Multiswitch to 1.5M dish(28.2E)
    ------------------> Spaun SUS 5581/33 NFA Multiswitch to 80 cm dish(19.2E)
    .......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
    AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using Legacy ports on multiswitches
    Zgemma H9 C/S into Giga4K

  5. #5
    TK4|2|1's Avatar
    Title
    Senior Member
    Join Date
    May 2011
    Location
    If there's a bright centre to the universe, I'm from the planet that is farthest from.
    Posts
    940
    Thanks
    228
    Thanked 180 Times in 159 Posts

    Client mode problem





    Best I can do on an iPad.
    No tuners are used on zero.
    It can't be tuner config if restating Oscam gets it running, can it?


    Sent from my iPad using Tapatalk
    Last edited by TK4|2|1; 18-07-17 at 19:14.

  6. #6
    twol's Avatar
    Title
    Moderator
    Join Date
    Apr 2012
    Posts
    8,382
    Thanks
    987
    Thanked 2,888 Times in 2,243 Posts
    No idea, but was interested to see your config. I am running my ET7500 from the GigaBlue 4K with a 'similar' unicable setup without issues but that is FTA (EN, DE), I have also run to most of my boxes in C/S mode without issue, so Yes, it has to be speciifc to your setup
    Gigablue Quad 4K & UE 4K
    .........FBC Tuners:
    ------------------> DUR-Line DCR 5-1-8-L4 Multiswitch to 1.5M dish(28.2E)
    ------------------> Spaun SUS 5581/33 NFA Multiswitch to 80 cm dish(19.2E)
    .......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
    AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using Legacy ports on multiswitches
    Zgemma H9 C/S into Giga4K

  7. #7
    TK4|2|1's Avatar
    Title
    Senior Member
    Join Date
    May 2011
    Location
    If there's a bright centre to the universe, I'm from the planet that is farthest from.
    Posts
    940
    Thanks
    228
    Thanked 180 Times in 159 Posts
    Thought I'd update you on how I resolved it.
    Gone back to CCcam, problem fixed.


    Sent from my iPad using Tapatalk

  8. The Following User Says Thank You to TK4|2|1 For This Useful Post:

    Bangord30 (13-08-17)

  9. #8

    Title
    Senior Member
    Join Date
    Sep 2013
    Posts
    622
    Thanks
    202
    Thanked 65 Times in 54 Posts
    title says client mode problem which seems a bit misleading.

  10. #9
    TK4|2|1's Avatar
    Title
    Senior Member
    Join Date
    May 2011
    Location
    If there's a bright centre to the universe, I'm from the planet that is farthest from.
    Posts
    940
    Thanks
    228
    Thanked 180 Times in 159 Posts
    Quote Originally Posted by imish View Post
    title says client mode problem which seems a bit misleading.
    How so?
    I had a problem with client mode.


    Sent from my iPad using Tapatalk

  11. #10

    Title
    Senior Member
    Join Date
    Sep 2013
    Posts
    622
    Thanks
    202
    Thanked 65 Times in 54 Posts
    Quote Originally Posted by TK4|2|1 View Post
    How so?
    I had a problem with client mode.


    Sent from my iPad using Tapatalk
    in your original post you say "I thought it may be client mode, so I installed RCSC onto the zero, but the same happens. "

  12. #11
    ccs's Avatar
    Title
    ViX Beta Tester
    Join Date
    Sep 2014
    Posts
    5,836
    Thanks
    554
    Thanked 1,276 Times in 1,089 Posts
    Sounds like a client mode problem to me.

  13. The Following User Says Thank You to ccs For This Useful Post:

    TK4|2|1 (15-08-17)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.