Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Results 1 to 8 of 8

Thread: Tuned Failed

  1. #1

    Title
    Junior Member
    Join Date
    Feb 2015
    Location
    Bilbao
    Posts
    13
    Thanks
    1
    Thanked 0 Times in 0 Posts

    Tuned Failed

    Every time I wake up my gigablue from standby I get a tuned failed message
    and have to restart the GUI and everything is fine again until the next time I
    put the box in standby mode.
    Is there a fix for this?
    Thanks
    Derek

  2. #2
    Huevos's Avatar
    Title
    Administrator
    Join Date
    Jun 2010
    Location
    38.5N, 0.5W
    Posts
    13,575
    Thanks
    2,004
    Thanked 4,925 Times in 3,259 Posts
    Who knows? You haven't told us anything about your setup, tuner config, etc.
    Help keep OpenViX servers online.Please donate!

  3. #3

    Title
    Junior Member
    Join Date
    Feb 2015
    Location
    Bilbao
    Posts
    13
    Thanks
    1
    Thanked 0 Times in 0 Posts
    Gigablue Quad plus 3 tuners , two satellite , one DVB on a community satellite dish astra 19e
    Tuner A astra 19e, tuner B Equal to A

  4. #4

    Title
    Junior Member
    Join Date
    Feb 2015
    Location
    Bilbao
    Posts
    13
    Thanks
    1
    Thanked 0 Times in 0 Posts
    only started happening after the latest update of the openvix firmware

  5. #5
    abu baniaz's Avatar
    Title
    Moderator
    Join Date
    Sep 2010
    Location
    East London
    Posts
    23,335
    Thanks
    6,421
    Thanked 9,146 Times in 6,224 Posts
    Your description of physical tuner setup and software tuner setup is very unclear. What about the third tuner? Do all the tuners have a wire connected?

    As you have determined it has been caused by an image update, use an older image.

  6. #6

    Title
    Junior Member
    Join Date
    Feb 2015
    Location
    Bilbao
    Posts
    13
    Thanks
    1
    Thanked 0 Times in 0 Posts
    Yes I know I can go back to an older firmware just thought there might have
    been a fix for this problem
    Both satellite tunes are connected and the third is DVB or TDT as you call it
    in the UK which is connected to an arial

  7. #7
    abu baniaz's Avatar
    Title
    Moderator
    Join Date
    Sep 2010
    Location
    East London
    Posts
    23,335
    Thanks
    6,421
    Thanked 9,146 Times in 6,224 Posts
    With all due respect, I don't believe there is an issue with the image. In my opinion, the issue is local and specific to your hardware. You need to fault find. One tuner at a time, one wire at a time and so forth.

  8. The Following User Says Thank You to abu baniaz For This Useful Post:

    josfit (12-06-17)

  9. #8

    Title
    Junior Member
    Join Date
    Feb 2015
    Location
    Bilbao
    Posts
    13
    Thanks
    1
    Thanked 0 Times in 0 Posts
    Well I have it back working as it should (fingers Crossed)
    What I have done was completely disconnect the box and not use it for a couple of days
    then after a couple of days reconnected the box backup installed the latest firmware and
    voila it was working as normal once again

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.