Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Page 3 of 4 FirstFirst 1234 LastLast
Results 31 to 45 of 49

Thread: What is eating my HDD space?

  1. #31
    ccs's Avatar
    Title
    ViX Beta Tester
    Join Date
    Sep 2014
    Posts
    5,836
    Thanks
    554
    Thanked 1,276 Times in 1,089 Posts
    I think having 2 threads isn't helping matters.

  2. #32

    Title
    Forum Supporter
    Donated Member
    Join Date
    Feb 2016
    Posts
    59
    Thanks
    16
    Thanked 27 Times in 25 Posts
    Have just tried a bit more experimentation, I plugged a 128gb usb/hdd into rear usb port this I had formatted on my pc to ext3. Went into setup/vix/mount-manager and mounted as usb, went to timeshift settings and set location for timeshift as the usb drive I had just mounted, checked information/devices and exactly 120gb free. Then I tried pause of live tv on hd channel and left it for 15 minutes before checking information/devices which stated 650mb had been used 119.35 gb free. Went back to tv and switched channels then back to information/devices and free space now shown as 120gb. Next tried timeshift on hd channel for approx same period of time and again around 650mb of space had been used, then disabled timeshift followed by channel change and return to information/devices to find disk space had again returned to 120gb. None of the unusual issues of disappearing hdd space were present, apart from location ie external usb rather than internal hdd the only difference in set up is my internal hdd is ext4 compared to the ext3 format I just tried. Is it the type of filesystem used causing issues

  3. #33

    Title
    Member
    Join Date
    Feb 2017
    Posts
    30
    Thanks
    17
    Thanked 5 Times in 3 Posts
    Quote Originally Posted by ljmramst View Post
    I had to reboot and in doing so for some reason I've lost all my epg settings, yeah all them days (see other forum).
    Sorry to hear that. I was able to spend a little bit of time yesterday to try to understand the wonders of Service searching and AutoBouquet makers for our machine.

    I have written down what I thought even I could understand, when I can't remember in a couple of weeks , at

    http://www.techkings.org/threads/is-...-3#post-682404

    Cheers!

  4. The Following User Says Thank You to speedygonzalez For This Useful Post:

    ljmramst (14-03-17)

  5. #34

    Title
    Member
    Join Date
    Feb 2017
    Posts
    30
    Thanks
    17
    Thanked 5 Times in 3 Posts
    Quote Originally Posted by 1999gtv View Post
    Have just tried a bit more experimentation, I plugged a 128gb usb/hdd into rear usb port this I had formatted on my pc to ext3. Went into setup/vix/mount-manager and mounted as usb, went to timeshift settings and set location for timeshift as the usb drive I had just mounted, checked information/devices and exactly 120gb free. Then I tried pause of live tv on hd channel and left it for 15 minutes before checking information/devices which stated 650mb had been used 119.35 gb free. Went back to tv and switched channels then back to information/devices and free space now shown as 120gb. Next tried timeshift on hd channel for approx same period of time and again around 650mb of space had been used, then disabled timeshift followed by channel change and return to information/devices to find disk space had again returned to 120gb. None of the unusual issues of disappearing hdd space were present, apart from location ie external usb rather than internal hdd the only difference in set up is my internal hdd is ext4 compared to the ext3 format I just tried. Is it the type of filesystem used causing issues
    I might have misunderstood what you are saying, but I have already tried pointing timeshift to a USB stick a couple of days ago. Like you what I found was the freespace in the usb stick behaved normally as expected, and the timeshift files in the stick looked perfectly normal also. However, the space loss issue remains, at the internal hdd.

    I think what happens, is as long as you have an internal hdd, the system would still use the hdd as workspace, irrespective where the timeshift directory is, and it is the release of the invisible workspace after use, not the timeshift files, that is buggy, and is causing the hdd space loss.

    Cheers!

  6. #35
    ccs's Avatar
    Title
    ViX Beta Tester
    Join Date
    Sep 2014
    Posts
    5,836
    Thanks
    554
    Thanked 1,276 Times in 1,089 Posts
    Odd that the vast majority of people are not seeing this problem, just a handful.

  7. #36

    Title
    Member
    Join Date
    Feb 2017
    Posts
    30
    Thanks
    17
    Thanked 5 Times in 3 Posts
    Quote Originally Posted by ccs View Post
    Odd that the vast majority of people are not seeing this problem, just a handful.
    Conversely it would be great if we can find even a single machine not suffering these problem when properly tested, because we can then try the image, and identify what the difference might be.

    Unfortunately, while some posters indicated in earlier posts that their machines were fine, they actually aren't, when tested and measured.

    There are now actually 3 threads, two are here as you say - I am sorry if I shouldn't have started the Vix Support thread this morning - I thought it is the proper way to get official support?

    Cheers!

  8. #37
    birdman's Avatar
    Title
    Moderator
    Join Date
    Sep 2014
    Location
    Hitchin, UK
    Posts
    7,764
    Thanks
    235
    Thanked 1,654 Times in 1,303 Posts
    Quote Originally Posted by kokojnr View Post
    It seems like the receiver somehow struggles to correctly read the available HDD space
    If someone could login to the commandline and run "df" to see what that reports it would be helpful then.

    And while they're at is running "dmesg" to see whether there are any unusual kernel message would also be useful.
    MiracleBox Prem Twin HD - 2@DVB-T2 + Xtrend et8000 - 5(incl. 2 different USBs)@DVB-T2[terrestrial - UK Freeview HD, Sandy Heath] - LAN/USB-stick/HDD

  9. The Following User Says Thank You to birdman For This Useful Post:

    speedygonzalez (15-03-17)

  10. #38

    Title
    Member
    Join Date
    Feb 2017
    Posts
    30
    Thanks
    17
    Thanked 5 Times in 3 Posts
    Quote Originally Posted by birdman View Post
    If someone could login to the commandline and run "df" to see what that reports it would be helpful then.

    And while they're at is running "dmesg" to see whether there are any unusual kernel message would also be useful.
    I have just done that. The hdd used and free space correspond with what is shown in OpenWebIf.

    Filesystem Size Used Available Use% Mounted on
    ubi0:rootfs 434.9M 71.2M 363.7M 16% /
    devtmpfs 277.5M 4.0K 277.5M 0% /dev
    tmpfs 64.0K 0 64.0K 0% /media
    tmpfs 277.6M 152.0K 277.5M 0% /var/volatile
    /dev/sda1 931.3G 60.5G 869.8G 7% /media/hdd

    The sizes found also correspond with what I have reported in the Support thread here (taken from Setup / Information / Devices page's figures), if one accounts for the binary to base 10 conversion, i.e. 1TB expressed as 931.3g.

    From dmesg:

    root@osmega:/media/hdd# dmesg
    Linux version 4.10.0 (vix@ns202814.ovh.net) (gcc version 6.3.0 (GCC) ) #1 SMP Wed Feb 22 16:47:13 CET 2017
    CPU0 revision is: 00025a11 (Broadcom BMIPS5000)
    FPU revision is: 00130001
    MIPS: machine is Broadcom BCM97346DBSMB
    Determined physical RAM map:
    memory: 04000000 @ 00000000 (usable)
    memory: 20000000 @ 30000000 (usable)
    Primary instruction cache 32kB, VIPT, 4-way, linesize 64 bytes.
    Primary data cache 32kB, 4-way, VIPT, no aliases, linesize 32 bytes
    MIPS secondary cache 256kB, 8-way, linesize 128 bytes.
    Zone ranges:
    Normal [mem 0x0000000000000000-0x000000001fffffff]
    HighMem [mem 0x0000000020000000-0x000000004fffffff]
    Movable zone start for each node
    Early memory node ranges
    node 0: [mem 0x0000000000000000-0x0000000003ffffff]
    node 0: [mem 0x0000000030000000-0x000000004fffffff]
    Initmem setup node 0 [mem 0x0000000000000000-0x000000004fffffff]
    On node 0 totalpages: 147456
    free_area_init_node: node 0, pgdat 80a42180, node_mem_map 8100d000
    Normal zone: 1024 pages used for memmap
    Normal zone: 0 pages reserved
    Normal zone: 16384 pages, LIFO batch:3
    HighMem zone: 131072 pages, LIFO batch:31
    percpu: Embedded 14 pages/cpu @81a10000 s26000 r8192 d23152 u57344
    pcpu-alloc: s26000 r8192 d23152 u57344 alloc=14*4096
    pcpu-alloc: [0] 0 [0] 1
    Built 1 zonelists in Zone order, mobility grouping on. Total pages: 146432
    Kernel command line: console=ttyS0,115200 ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs
    PID hash table entries: 256 (order: -2, 1024 bytes)
    Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
    Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
    Memory: 568240K/589824K available (8432K kernel code, 331K rwdata, 1680K rodata, 300K init, 294K bss, 21584K reserved, 0K cma-reserved, 524288K highmem)
    SLUB: HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
    Hierarchical RCU implementation.
    Build-time adjustment of leaf fanout to 32.
    RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
    RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
    NR_IRQS:128
    irq_bcm7038_l1: registered BCM7038 L1 intc (mem: 0xb0411400, IRQs: 96)
    irq_brcmstb_l2: registered L2 intc (mem: 0xb0403000, parent irq: 59)
    irq_bcm7120_l2: registered BCM7120 L2 intc (mem: 0xb0406780, parent IRQ(s): 2)
    irq_bcm7120_l2: registered BCM7120 L2 intc (mem: 0xb0408b80, parent IRQ(s): 3)
    irq_brcmstb_l2: registered L2 intc (mem: 0xb0408440, parent irq: 61)
    irq_brcmstb_l2: registered L2 intc (mem: 0xb0411000, parent irq: 38)
    irq_brcmstb_l2: registered L2 intc (mem: 0xb0411d00, parent irq: 39)
    clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9544355085 ns
    sched_clock: 32 bits at 250 Hz, resolution 4000000ns, wraps every 8589934590000000ns
    Console: colour dummy device 80x25
    Calibrating delay loop... 1062.91 BogoMIPS (lpj=2125824)
    pid_max: default: 32768 minimum: 301
    Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
    Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
    smp: Bringing up secondary CPUs ...
    SMP: Booting CPU1...
    Primary instruction cache 32kB, VIPT, 4-way, linesize 64 bytes.
    Primary data cache 32kB, 4-way, VIPT, no aliases, linesize 32 bytes
    MIPS secondary cache 256kB, 8-way, linesize 128 bytes.
    CPU1 revision is: 00025a11 (Broadcom BMIPS5000)
    FPU revision is: 00130001
    Synchronize counters for CPU 1:
    done.
    SMP: CPU1 is running
    smp: Brought up 1 node, 2 CPUs
    devtmpfs: initialized
    clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
    futex hash table entries: 512 (order: 4, 65536 bytes)
    NET: Registered protocol family 16
    SCSI subsystem initialized
    libata version 3.00 loaded.
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    Linux video capture interface: v2.00
    Advanced Linux Sound Architecture Driver Initialized.
    Bluetooth: Core ver 2.22
    NET: Registered protocol family 31
    Bluetooth: HCI device and connection manager initialized
    Bluetooth: HCI socket layer initialized
    Bluetooth: L2CAP socket layer initialized
    Bluetooth: SCO socket layer initialized
    clocksource: Switched to clocksource MIPS
    FS-Cache: Loaded
    NET: Registered protocol family 2
    TCP established hash table entries: 1024 (order: 0, 4096 bytes)
    TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
    TCP: Hash tables configured (established 1024 bind 1024)
    UDP hash table entries: 256 (order: 1, 8192 bytes)
    UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
    NET: Registered protocol family 1
    RPC: Registered named UNIX socket transport module.
    RPC: Registered udp transport module.
    RPC: Registered tcp transport module.
    RPC: Registered tcp NFSv4.1 backchannel transport module.
    workingset: timestamp_bits=30 max_order=18 bucket_order=0
    NFS: Registering the id_resolver key type
    Key type id_resolver registered
    Key type id_legacy registered
    nfs4filelayout_init: NFSv4 File Layout Driver Registering...
    Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
    fuse init (API version 7.26)
    random: fast init done
    bounce: pool size: 64 pages
    Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
    io scheduler noop registered
    io scheduler deadline registered
    io scheduler cfq registered (default)
    brcm-gisb-arb 10400000.gisb-arb: registered mem: b0400000, irqs: 104, 105
    brcm-sata-phy 10180100.sata-phy: registered 2 port(s)
    brcmstb-gpio 10406700.gpio: Registered 3 banks (GPIO(s): 0-95)
    brcmstb-gpio 10408c00.gpio: Registered 3 banks (GPIO(s): 96-191)
    Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    console [ttyS0] disabled
    10406900.serial: ttyS0 at MMIO 0x10406900 (irq = 72, base_baud = 5062500) is a 16550A
    console [ttyS0] enabled
    10406940.serial: ttyS1 at MMIO 0x10406940 (irq = 73, base_baud = 5062500) is a 16550A
    10406980.serial: ttyS2 at MMIO 0x10406980 (irq = 74, base_baud = 5062500) is a 16550A
    [drm] Initialized
    loop: module loaded
    brcm-ahci 10181000.sata: controller can't do NCQ, turning off CAP_NCQ
    brcm-ahci 10181000.sata: masking port_map 0x3 -> 0x3
    brcm-ahci 10181000.sata: SSS flag set, parallel bus scan disabled
    brcm-ahci 10181000.sata: AHCI 0001.0300 32 slots 3 ports 6 Gbps 0x3 impl platform mode
    brcm-ahci 10181000.sata: flags: sntf stag pm clo pmp slum part
    scsi host0: brcm-ahci
    scsi host1: brcm-ahci
    scsi host2: brcm-ahci
    ata1: SATA max UDMA/133 mmio [mem 0x10181000-0x10181a9b] port 0x100 irq 48
    ata2: SATA max UDMA/133 mmio [mem 0x10181000-0x10181a9b] port 0x180 irq 48
    ata3: DUMMY
    brcm-ahci 10181000.sata: Broadcom AHCI SATA3 registered
    nand: device found, Manufacturer ID: 0x01, Chip ID: 0xdc
    nand: AMD/Spansion S34ML04G2
    nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
    brcmstb_nand 10412800.nand: detected 512MiB total, 128KiB blocks, 2KiB pages, 32B OOB, 8-bit, BCH-4
    Bad block table found at page 262080, version 0x01
    Bad block table found at page 262016, version 0x01
    3 ofpart partitions found on MTD device brcmnand.1
    Creating 3 MTD partitions on "brcmnand.1":
    0x000000000000-0x000000800000 : "kernel"
    0x000000800000-0x000000c00000 : "splash"
    0x000000c00000-0x00001fe00000 : "rootfs"
    brcmstb_qspi 10410920.spi: using bspi-mspi mode
    m25p80 spi32766.0: found mx25l3205d, expected m25p80
    m25p80 spi32766.0: mx25l3205d (4096 Kbytes)
    3 ofpart partitions found on MTD device spi32766.0
    Creating 3 MTD partitions on "spi32766.0":
    0x000000000000-0x0000000a0000 : "cfe"
    0x0000000a0000-0x0000000b0000 : "nvram"
    0x0000000b0000-0x0000000c0000 : "mac"
    libphy: Fixed MDIO Bus: probed
    bcmgenet 10430000.ethernet: failed to get enet clock
    bcmgenet 10430000.ethernet: GENET 2.9 EPHY: 0x00b0
    bcmgenet 10430000.ethernet: failed to get enet-wol clock
    ata1: SATA link down (SStatus 0 SControl 300)
    bcmgenet 10430000.ethernet: failed to get enet-eee clock
    libphy: bcmgenet MII bus: probed
    usbcore: registered new interface driver zd1201
    ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    ehci-platform: EHCI generic platform driver
    ehci-platform 10480300.usb: EHCI Host Controller
    ehci-platform 10480300.usb: new USB bus registered, assigned bus number 1
    ehci-platform 10480300.usb: irq 76, io mem 0x10480300
    ehci-platform 10480300.usb: USB 2.0 started, EHCI 1.00
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 1 port detected
    ehci-platform 10480500.usb: EHCI Host Controller
    ehci-platform 10480500.usb: new USB bus registered, assigned bus number 2
    ehci-platform 10480500.usb: irq 77, io mem 0x10480500
    ehci-platform 10480500.usb: USB 2.0 started, EHCI 1.00
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 1 port detected
    ehci-platform 10490300.usb: EHCI Host Controller
    ehci-platform 10490300.usb: new USB bus registered, assigned bus number 3
    ehci-platform 10490300.usb: irq 81, io mem 0x10490300
    ehci-platform 10490300.usb: USB 2.0 started, EHCI 1.00
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 1 port detected
    ehci-platform 10490500.usb: EHCI Host Controller
    ehci-platform 10490500.usb: new USB bus registered, assigned bus number 4
    ehci-platform 10490500.usb: irq 82, io mem 0x10490500
    ehci-platform 10490500.usb: USB 2.0 started, EHCI 1.00
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 1 port detected
    ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    ohci-platform: OHCI generic platform driver
    ohci-platform 10480400.usb: Generic Platform OHCI controller
    ohci-platform 10480400.usb: new USB bus registered, assigned bus number 5
    ohci-platform 10480400.usb: irq 78, io mem 0x10480400
    ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
    hub 5-0:1.0: USB hub found
    hub 5-0:1.0: 1 port detected
    ohci-platform 10480600.usb: Generic Platform OHCI controller
    ohci-platform 10480600.usb: new USB bus registered, assigned bus number 6
    ata2.00: ATA-8: TOSHIBA MQ01ABD100, AX0R2J, max UDMA/100
    ata2.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
    ata2.00: configured for UDMA/100
    ohci-platform 10480600.usb: irq 79, io mem 0x10480600
    scsi 1:0:0:0: Direct-Access ATA TOSHIBA MQ01ABD1 2J PQ: 0 ANSI: 5
    sd 1:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
    sd 1:0:0:0: [sda] 4096-byte physical blocks
    sd 1:0:0:0: Attached scsi generic sg0 type 0
    sd 1:0:0:0: [sda] Write Protect is off
    sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    hub 6-0:1.0: USB hub found
    hub 6-0:1.0: 1 port detected
    ohci-platform 10490400.usb: Generic Platform OHCI controller
    ohci-platform 10490400.usb: new USB bus registered, assigned bus number 7
    ohci-platform 10490400.usb: irq 83, io mem 0x10490400
    hub 7-0:1.0: USB hub found
    hub 7-0:1.0: 1 port detected
    ohci-platform 10490600.usb: Generic Platform OHCI controller
    ohci-platform 10490600.usb: new USB bus registered, assigned bus number 8
    ohci-platform 10490600.usb: irq 84, io mem 0x10490600
    sda: sda1
    sd 1:0:0:0: [sda] Attached SCSI disk
    hub 8-0:1.0: USB hub found
    hub 8-0:1.0: 1 port detected
    usbcore: registered new interface driver usb-storage
    mousedev: PS/2 mouse device common for all mice
    i2c /dev entries driver
    brcmstb-i2c 10406200.i2c: upg_bsca@97500hz registered in interrupt mode
    brcmstb-i2c 10406280.i2c: upg_bscb@97500hz registered in interrupt mode
    brcmstb-i2c 10406300.i2c: upg_bscc@97500hz registered in interrupt mode
    brcmstb-i2c 10406380.i2c: upg_bscd@97500hz registered in interrupt mode
    brcmstb-i2c 10408980.i2c: upg_bsce@97500hz registered in interrupt mode
    usbcore: registered new interface driver btusb
    bmips-cpufreq: registered
    sdhci: Secure Digital Host Controller Interface driver
    sdhci: Copyright(c) Pierre Ossman
    sdhci-pltfm: SDHCI platform and OF driver helper
    sdhci-brcmstb 10413500.sdhci: Clock not found in Device Tree
    mmc0: SDHCI controller on 10413500.sdhci [10413500.sdhci] using ADMA
    hidraw: raw HID events driver (C) Jiri Kosina
    usbcore: registered new interface driver usbhid
    usbhid: USB HID core driver
    NET: Registered protocol family 17
    Bluetooth: HIDP (Human Interface Emulation) ver 1.2
    Bluetooth: HIDP socket layer initialized
    Key type dns_resolver registered
    ubi0: attaching mtd2
    mmc0: new high speed SDIO card at address 0001
    random: crng init done
    ubi0: scanning is finished
    ubi0: attached mtd2 (name "rootfs", size 498 MiB)
    ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
    ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
    ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
    ubi0: good PEBs: 3984, bad PEBs: 0, corrupted PEBs: 0
    ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
    ubi0: max/mean erase counter: 5/3, WL threshold: 4096, image sequence number: 909706988
    ubi0: available PEBs: 0, total reserved PEBs: 3984, PEBs reserved for bad PEB handling: 80
    ubi0: background thread "ubi_bgt0d" started, PID 79
    ALSA device list:
    No soundcards found.
    UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs", R/O mode
    UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
    UBIFS (ubi0:0): FS size: 493809664 bytes (470 MiB, 3889 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
    UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB)
    UBIFS (ubi0:0): media format: w4/r0 (latest is w5/r0), UUID E7473C0E-46D3-4F2F-AD69-F9E4A95D1E77, small LPT model
    VFS: Mounted root (ubifs filesystem) readonly on device 0:13.
    devtmpfs: mounted
    Freeing unused kernel memory: 300K
    This architecture does not have kernel memory protection.
    EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
    ftm4862: loading out-of-tree module taints kernel.
    ftm4862: module license 'Proprietary' taints kernel.
    Disabling lock debugging due to kernel taint
    dvbdev: DVB: registering new adapter (Broadcom BCM7xxx)
    input: dreambox advanced remote control (native) as /devices/virtual/misc/brcmstb/input0
    input: dreambox ir mouse as /devices/virtual/misc/brcmstb/input1
    input: dreambox front panel as /devices/virtual/misc/brcmstb/input2
    misc brcmstb: DVB: registering adapter 0 frontend 0 (Broadcom BCM73XX)...
    misc brcmstb: DVB: registering adapter 0 frontend 1 (Broadcom BCM73XX)...
    misc brcmstb: DVB: registering adapter 0 frontend 2 (FTM-4862 (Availink AVL6862))...
    Bluetooth: HCI UART driver ver 2.3
    Bluetooth: HCI UART protocol H4 registered
    Bluetooth: HCI UART protocol BCSP registered
    Bluetooth: HCI UART protocol LL registered
    Bluetooth: HCI UART protocol Three-wire (H5) registered
    RTL871X: module init start
    RTL871X: rtl8723bs v4.4.1_17245.20160325_BTCOEX20151223-654a
    RTL871X: build time: Feb 22 2017 16:52:15
    RTL871X: rtl8723bs BT-Coex version = BTCOEX20151223-654a
    RTL871X: hal_com_config_channel_plan chplan:0x21
    RTL871X: rtw_ndev_init(wlan0) if1 mac_addr=e0:b9:4d:9d:6d:b2
    RTL871X: module init ret=0
    SGI XFS with security attributes, realtime, no debug enabled
    UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 331
    NET: Registered protocol family 10
    Segment Routing with IPv6
    bcmgenet 10430000.ethernet: configuring instance for external RGMII (no delay)
    IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    bcmgenet 10430000.ethernet eth0: Link is Down
    bcmgenet 10430000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
    IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    bcmgenet 10430000.ethernet eth0: Link is Up - 10Mbps/Full - flow control rx/tx
    bcmgenet 10430000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off
    root@osmega:/media/hdd#


    Cheers!

  11. #39
    ccs's Avatar
    Title
    ViX Beta Tester
    Join Date
    Sep 2014
    Posts
    5,836
    Thanks
    554
    Thanked 1,276 Times in 1,089 Posts
    One thing dmesg says is "1.00 TB/932 GiB", which might be part of the answer?
    Last edited by ccs; 15-03-17 at 13:08.

  12. #40
    birdman's Avatar
    Title
    Moderator
    Join Date
    Sep 2014
    Location
    Hitchin, UK
    Posts
    7,764
    Thanks
    235
    Thanked 1,654 Times in 1,303 Posts
    Quote Originally Posted by ccs View Post
    One thing dmesg says is "1.00 TB/932 GiB", which might be part of the answer?
    That's just the difference between TB (10^12) and GiB (1024^3).
    MiracleBox Prem Twin HD - 2@DVB-T2 + Xtrend et8000 - 5(incl. 2 different USBs)@DVB-T2[terrestrial - UK Freeview HD, Sandy Heath] - LAN/USB-stick/HDD

  13. #41
    ccs's Avatar
    Title
    ViX Beta Tester
    Join Date
    Sep 2014
    Posts
    5,836
    Thanks
    554
    Thanked 1,276 Times in 1,089 Posts
    Quote Originally Posted by birdman View Post
    That's just the difference between TB (10^12) and GiB (1024^3).
    I know, but maybe ViX, or whatever, is using both forms in different contexts.
    Last edited by ccs; 15-03-17 at 13:59.

  14. #42

    Title
    Junior Member
    Join Date
    Mar 2017
    Posts
    8
    Thanks
    2
    Thanked 0 Times in 0 Posts
    Noticed something has been fixed, http://www.world-of-satellite.com/sh...-build-5-0-004

    Just ordered this box knowing it is so well supported.

  15. #43

    Title
    Senior Member
    Join Date
    Jul 2014
    Posts
    229
    Thanks
    31
    Thanked 11 Times in 11 Posts
    Has this been sorted out yet?

  16. #44
    ccs's Avatar
    Title
    ViX Beta Tester
    Join Date
    Sep 2014
    Posts
    5,836
    Thanks
    554
    Thanked 1,276 Times in 1,089 Posts
    Quote Originally Posted by gilvey View Post
    Has this been sorted out yet?
    ...try the post before yours.

  17. #45

    Title
    Senior Member
    Join Date
    Jul 2014
    Posts
    229
    Thanks
    31
    Thanked 11 Times in 11 Posts
    Not very good if you've already got 1tb of recordings you want your keep though is it?

Page 3 of 4 FirstFirst 1234 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.