Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Results 1 to 6 of 6

Thread: new remote not working with nano 2 super

  1. #1

    Title
    Junior Member
    Join Date
    Nov 2014
    Posts
    5
    Thanks
    1
    Thanked 0 Times in 0 Posts

    new remote not working with nano 2 super

    I have two nano 2 super boxes and only one remote control is working all are new ie: batteries and boxes they are the new style remote controls any ideas ?

  2. #2
    Stanman's Avatar
    Title
    Junior Admin
    Donated Member
    Join Date
    May 2010
    Posts
    11,284
    Thanks
    1,035
    Thanked 3,599 Times in 2,632 Posts
    Any buttons stuck?

    Sent from my SM-N9005 using Tapatalk

    Support The Sponsor - Buy from the best HERE
    Please abide by the rules - have a read HERE
    VIX manual & guides >>HERE
    Download images from >> HERE
    New Box Setup Guide >>HERE

    D I S C L A I M E R
    My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!

    PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE


    Follow us on Twitter

    NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN! IN OPEN FORUM OR PM

    IF THE POSTS HELP PLEASE CLICK THANKS OR ADD TO REP ?



  3. #3
    Larry-G's Avatar
    Title
    V.I.P
    Donated Member
    Join Date
    May 2010
    Posts
    32,542
    Thanks
    7,824
    Thanked 22,934 Times in 12,378 Posts
    Does it actually say Nano on the remote ? because TM use pretty much the same remote for all boxes with different codes for each. The Base 4D image by Technomate (although they will tell you it is nothing to do with them) carries a app to change the RCU code via the receiver like the Vu+ one does in ViX but ViX does not have this one for TM boxes within the image.

    Also try checking the remote is actually working, Hold the remote up to a cell phone in camera mode, then press a few buttons on the remote. you should see a white flash on the phone screen as it detects the IR signal. If you dont see this flash the remote control it self is faulty, if you do then it is running the code for a different TM receiver.
    My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.

    If you don't like what I post, Don't read it.

    SIMPLES.

  4. The Following User Says Thank You to Larry-G For This Useful Post:

    abu baniaz (19-07-15)

  5. #4

    Title
    Junior Member
    Join Date
    Nov 2014
    Posts
    5
    Thanks
    1
    Thanked 0 Times in 0 Posts
    the remote works on the other box its like as if I don't have the right remote
    but the two boxes are tm nano2 super both remotes the same the new type and both remotes work on one box and not on the other ?

  6. #5
    Larry-G's Avatar
    Title
    V.I.P
    Donated Member
    Join Date
    May 2010
    Posts
    32,542
    Thanks
    7,824
    Thanked 22,934 Times in 12,378 Posts
    so both remotes work with one box but none with the second one ? if thats the case either the receiver has the wrong code preset for the remote or the IR sensor on the receiver is broken / misaligned.

    Try reflahing the affected receiver with a new clean image and see if either remote works during the initial setup wizard.
    My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.

    If you don't like what I post, Don't read it.

    SIMPLES.

  7. #6

    Title
    Junior Member
    Join Date
    Nov 2014
    Posts
    5
    Thanks
    1
    Thanked 0 Times in 0 Posts
    new image flash hades 018 fixed with clean setup not restore thanks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.