Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Page 3 of 4 FirstFirst 1234 LastLast
Results 31 to 45 of 46

Thread: et9000 cant get past bootloader

  1. #31

    Title
    Senior Member
    Join Date
    Jul 2011
    Posts
    339
    Thanks
    112
    Thanked 42 Times in 37 Posts
    I can flash the new boot loader, and then flash Vix 2.3. All works OK and the box runs OK

    However if I try to restart it it just hangs on the first 'page'.

    I did a force reflash of the boot loader using a different stick, flashed Vix 2.3 again - same problem

    I have also tried flashing the latest Clarke-Tech image, but I get the same problem. i.e box works after flash until I reboot it.

    (I should say that this is box 2, I did box 1 on Sunday, and it works OK -apart from not being able to make a backup image)problem?

    I would be grateful for any suggestions as to how to overcome this problem.

  2. #32
    Stanman's Avatar
    Title
    Junior Admin
    Donated Member
    Join Date
    May 2010
    Posts
    11,284
    Thanks
    1,035
    Thanked 3,599 Times in 2,632 Posts
    DO you have anything else connected such as a HDD, if so try it with unplugged and see what happens.

    Support The Sponsor - Buy from the best HERE
    Please abide by the rules - have a read HERE
    VIX manual & guides >>HERE
    Download images from >> HERE
    New Box Setup Guide >>HERE

    D I S C L A I M E R
    My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!

    PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE


    Follow us on Twitter

    NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN! IN OPEN FORUM OR PM

    IF THE POSTS HELP PLEASE CLICK THANKS OR ADD TO REP ?



  3. #33

    Title
    Senior Member
    Join Date
    Jul 2011
    Posts
    339
    Thanks
    112
    Thanked 42 Times in 37 Posts
    Quote Originally Posted by Stanman View Post
    DO you have anything else connected such as a HDD, if so try it with unplugged and see what happens.
    I have now disconnected the HD, and everything except the HDMI cable. Still won't boot,

  4. #34
    Stanman's Avatar
    Title
    Junior Admin
    Donated Member
    Join Date
    May 2010
    Posts
    11,284
    Thanks
    1,035
    Thanked 3,599 Times in 2,632 Posts
    leave the network cable in there and download a fresh copy of the image and reflash in case image got corrupted in download.

    Are you sure the bootloader was updated?

    What do you mean by forced flash?

    Support The Sponsor - Buy from the best HERE
    Please abide by the rules - have a read HERE
    VIX manual & guides >>HERE
    Download images from >> HERE
    New Box Setup Guide >>HERE

    D I S C L A I M E R
    My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!

    PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE


    Follow us on Twitter

    NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN! IN OPEN FORUM OR PM

    IF THE POSTS HELP PLEASE CLICK THANKS OR ADD TO REP ?



  5. #35

    Title
    Senior Member
    Join Date
    Jul 2011
    Posts
    339
    Thanks
    112
    Thanked 42 Times in 37 Posts
    Quote Originally Posted by Stanman View Post
    leave the network cable in there and download a fresh copy of the image and reflash in case image got corrupted in download.

    Are you sure the bootloader was updated?

    What do you mean by forced flash?
    I have tried 3 different Vix images that I have downloaded. One of which + the boot loader are working on my other box.

    The box displays ET9x00 and looks for images in et9x00 so I assume that I am using the new boot loader.

    By Force Flash, I mean pressing CH- on the front panel to flash the boot loader again (I think the loader on the stick gets ignored if you try to flash the same one twice just by pressing OK.)

  6. #36
    Stanman's Avatar
    Title
    Junior Admin
    Donated Member
    Join Date
    May 2010
    Posts
    11,284
    Thanks
    1,035
    Thanked 3,599 Times in 2,632 Posts
    If you have no other usb devices connected, the box will automatically see the image and ask you to press OK flash, if your not getting this, is the folder structure correct?

    Support The Sponsor - Buy from the best HERE
    Please abide by the rules - have a read HERE
    VIX manual & guides >>HERE
    Download images from >> HERE
    New Box Setup Guide >>HERE

    D I S C L A I M E R
    My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!

    PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE


    Follow us on Twitter

    NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN! IN OPEN FORUM OR PM

    IF THE POSTS HELP PLEASE CLICK THANKS OR ADD TO REP ?



  7. #37

    Title
    Senior Member
    Join Date
    Jul 2011
    Posts
    339
    Thanks
    112
    Thanked 42 Times in 37 Posts
    Quote Originally Posted by Stanman View Post
    If you have no other usb devices connected, the box will automatically see the image and ask you to press OK flash, if your not getting this, is the folder structure correct?
    For images yes, for boot loaders the box finds the loader but appears to ignore it if you just press OK.

  8. #38
    Stanman's Avatar
    Title
    Junior Admin
    Donated Member
    Join Date
    May 2010
    Posts
    11,284
    Thanks
    1,035
    Thanked 3,599 Times in 2,632 Posts
    its a very quick flash, no way near the length of an image. obviously the new image is in the9x00 format, bit stumped why you are having the problem

    Support The Sponsor - Buy from the best HERE
    Please abide by the rules - have a read HERE
    VIX manual & guides >>HERE
    Download images from >> HERE
    New Box Setup Guide >>HERE

    D I S C L A I M E R
    My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!

    PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE


    Follow us on Twitter

    NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN! IN OPEN FORUM OR PM

    IF THE POSTS HELP PLEASE CLICK THANKS OR ADD TO REP ?



  9. The Following User Says Thank You to Stanman For This Useful Post:

    machare (21-12-11)

  10. #39

    Title
    Senior Member
    Join Date
    Jul 2011
    Posts
    339
    Thanks
    112
    Thanked 42 Times in 37 Posts
    I have even tried flashing the boot loader from the Clarke-Tech support forum

  11. #40
    Stanman's Avatar
    Title
    Junior Admin
    Donated Member
    Join Date
    May 2010
    Posts
    11,284
    Thanks
    1,035
    Thanked 3,599 Times in 2,632 Posts
    Lets just go back to basics and redo everything in the unlikely event you have missed a step out.

    Go to the VIX 2.3 release thread and download both the image and bootloader.

    Unzip the BL and put it on to the USB and reflash. The file you need is called ET9000, its the 2nd folder in. Dont bother wiht the MAC one that can be deleted. Once transferred to the USB check that there are only three files inside it.

    Once completed do the same with the image.

    One other think you could try is to switch and leave the box off for a minute and see if it boots.

    Support The Sponsor - Buy from the best HERE
    Please abide by the rules - have a read HERE
    VIX manual & guides >>HERE
    Download images from >> HERE
    New Box Setup Guide >>HERE

    D I S C L A I M E R
    My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!

    PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE


    Follow us on Twitter

    NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN! IN OPEN FORUM OR PM

    IF THE POSTS HELP PLEASE CLICK THANKS OR ADD TO REP ?



  12. #41
    Alias1
    =Stanman;102378
    One other think you could try is to switch and leave the box off for a minute and see if it boots.
    It can take up to a minute before all caps discharge in the box

  13. #42

    Title
    Senior Member
    Join Date
    Jul 2011
    Posts
    339
    Thanks
    112
    Thanked 42 Times in 37 Posts
    Quote Originally Posted by Stanman View Post
    Lets just go back to basics and redo everything in the unlikely event you have missed a step out.

    Go to the VIX 2.3 release thread and download both the image and bootloader.

    Unzip the BL and put it on to the USB and reflash. The file you need is called ET9000, its the 2nd folder in. Dont bother wiht the MAC one that can be deleted. Once transferred to the USB check that there are only three files inside it.

    Once completed do the same with the image.

    One other think you could try is to switch and leave the box off for a minute and see if it boots.

    Thanks very much for all your help.

    I have verified that the stuff I put on the USB sticks is correct by comparing the files with other downloads, and I have repeated the process, so I am fairly certain that I have just run into the same problem as Cameltoe and Torsven. I will try the supplier!

  14. #43
    Rimmel's Avatar
    Title
    Forum Supporter
    Donated Member
    Join Date
    Sep 2011
    Posts
    323
    Thanks
    64
    Thanked 68 Times in 13 Posts
    I got it working - switch of the box after bootloader flash and after main flash.

    Thanks for the help

  15. The Following 3 Users Say Thank You to Rimmel For This Useful Post:

    Cucosat (30-12-11),Larry-G (22-12-11),Sicilian (22-12-11)

  16. #44
    parkher
    Not quite on this topic, but still about bootloaders and the 2.3 image.

    When I got ET9000, I flashed the new at the time bootloader 2011-07-19 (UBIFS).
    If I understood it correctly, it was not really needed for the 2.2.1 image but was supposed to be needed with the new kernel later, with the new upcoming 2.3 image (and also to solve the image size limitations).
    So can I load the 2.3 image with that bootloader or do I need the newest bootloader, the one that comes together with the 2.3 image?

  17. #45
    Larry-G's Avatar
    Title
    V.I.P
    Donated Member
    Join Date
    May 2010
    Posts
    32,542
    Thanks
    7,824
    Thanked 22,934 Times in 12,378 Posts
    yes you need to use the bootloader that is in the 2.3 release thread due to the changes xtrend made to the way the image works.
    My posts contain my own personal thoughts and opinions, they do not represent those of any organisation or group but my own.

    If you don't like what I post, Don't read it.

    SIMPLES.

  18. The Following User Says Thank You to Larry-G For This Useful Post:


Page 3 of 4 FirstFirst 1234 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.