do I need to install drivers to use USB smartmouse reader in vu+ duo?!!!

[amuceku]

hi. i need to use easymouse2 reader with oscam.
if yes wher can i get the drivers?

[andyblac]

it all depends and the image you choose to use, in ViX the drivers pre-installed already. but you will still need to install a softcam.

[amuceku]

it all depends and the image you choose to use, in ViX the drivers pre-installed already. but you will still need to install a softcam.

hi andy, thank you for the reply. yes i use vix2.2 and oscam. i have done all the configurations for oscam. but it fails to read the card from the reader.
oscam does read the internal readers without problem....

[guli]

All different settings for cardreaders ( smargo, omnikey, etc.)

# serial reader

[reader]
label = reader1
protocol = mouse
detect = CD
device = /dev/ttyS0
group = 1
emmcache = 1,3,2
services = services1
caid = 0100

# USB serial reader

[reader]
label = reader2
protocol = mouse
detect = CD
device = /dev/ttyUSB0
aeskey = 000102030405060708090A0B0C0D0E0F
group = 2
emmcache = 1,3,2
services = services2
caid = 0200

# remote newcamd reader with fallback for group 1

[reader]
label = remote1
protocol = newcamd
key = 0102030405060708091011121314
device = 192.168.0.2,66666
account = login1,password1
group = 1
fallback = 1

# remote camd 3.78x reader with fallback for group 2

[reader]
label = remote2
protocol = cs378x
device = 192.168.0.3,23456
account = login2,password2
group = 2
fallback = 1

# remote gbox reader

[reader]
label = remote3
protocol = gbox
device = 192.168.0.4,34567,45678
account = login3,password3
group = 3
caid = 0300

# remote CCcam reader

[reader]
label = remote4
protocol = cccam
device = 192.168.0.5,45678
account = login4,password4
group = 4
caid = 0400
cccversion = 1.2.34
cccbuild = 5678

# remote radegast reader

[reader]
label = remote5
protocol = radegast
device = 192.168.0.6,56789
group = 5
caid = 0500

# PCSC reader

[reader]
label = mypcscreader
protocol = pcsc
device = 0
aeskey = 0102030405060708090a0b0c0d0e0f10
group = 6
caid = 0600

# Smargo Smartreader+

[reader]
label = mysmartreader
protocol = smartreader
device = 001:002
aeskey = 0102030405060708090a0b0c0d0e0f10
group = 7
caid = 0700

# internal reader

[reader]
label = myinternalreader
protocol = internal
device = /dev/sci0
group = 8
caid = 0800

# AD-Teknik AB Multiprogrammer 3.5 serial

[reader]
label = reader9
protocol = mp35
detect = CD
device = /dev/ttyS1
group = 9
emmcache = 1,3,2
services = services9
caid = 0900

# AD-Teknik AB Multiprogrammer 3.6 USB

[reader]
label = reader10
protocol = mp35
detect = CD
device = /dev/ttyUSB1
group = 10
emmcache = 1,3,2
services = services10
caid = 1000

# AD-Teknik AB USB Phoenix at 6.00 mhz

[reader]
label = reader11
protocol = mp35
detect = CD
device = /dev/ttyUSB2
mhz = 600
group = 11
emmcache = 1,3,2
services = services11
caid = 1100

[Sicilian]

Are you using a easymouse2 reader or smargo, smargo drivers are pre-installed not easymouse2 reader.

[amuceku]

Are you using a easymouse2 reader or smargo, smargo drivers are pre-installed not easymouse2 reader.
yes is easymouse2... any idea how to get the drivers for this? thanks

[kphbus]

Hi Just purchased 5 Crystal USB Card Reader Inc Phoenix/Smartmouse mode. can anyone tell me were to find all the instructions on how to set up what settings basically noddy instructions. / what I need to set up and use on my vu+ duo. You can pm me if you prefer.