View Full Version : Satellite dish motorised setup
Hi all,
I need your help.
I have been told by someone on the other forum that I have set up incorrect settings when I setup the rig on dead straight (remember with 3 dots) with motor set to 0 then I moved the whole rig to 0.8west with motor set to 0. He said that it should be 2-3 degree.
Do the motor need to be on 0 when I move the rig on dead straight like 12 o clock and do the dish need to be 2-3 gree when I move the dish to 0.8west?
If not, do I need to move the whole rig to 0.8west with the motor set to 0 as the motor is not on dead straight?
I think I have setup incorrect as the motor is not on dead straight when I moved the whole rig to 0.8west with the motor set to 0. I guess the motor need to be on dead straight as the motor set to 0 and I think I need to undo the nuts on the brackets that holds on the motor arm to move the dish to 0.8west.
Please let me know which one of them is correct.
Any advice would be much appreciated.
You always keep the motor lined up dead straight with dish, you drive the motor and dish to 0.8 via stb and if any adjustment needed to get correct signal you slacken nuts on motor that connects to wall bracket and move dish and motor manually by hand to get best signal on 0.8 channel then tighten up bolts again on motor bracket.
You always keep the motor lined up dead straight with dish, you drive the motor and dish to 0.8 via stb and if any adjustment needed to get correct signal you slacken nuts on motor that connects to wall bracket and move dish and motor manually by hand to get best signal on 0.8 channel then tighten up bolts again on motor bracket.
Oh right, when I set the motor lined up dead straight with the dish as the motor is set to 0, do I have to go on the stub to select the channel?
How do the motor know where is 0.8west?
If not, do I have to move the motor with the dish lined up as dead straight to move the rig to 0.8west?
Which one?
chris0147 - you line up the dish and motor (set to 0) to point south wherever you are located. So, in the direction of the sun at local noon. Where I am (county Wicklow, south of Dublin)the sun is due south of me right now (12.25ish). If you are on the Greenwich meridian (which runs through London), local noon is at 12.00.
Assuming you have your north/east(or west) coordinates set correctly in the box you then tune to the satellite that is nearest your due south. This is the so-called "top of the arc" or closest to 0 on the motor. If you are in the eastern side of GB, then the 0.8W satellite is your "top of the arc". For someone in west Wales (or for me), then 5W is the top. The box will calculate the angle to the satellite from the location coordinates stored in the box. In my case, the motor will turn a little bit to the east as my motor zero position is at 6W (my longitude). If you were really accurate in lining up due south originally, then the dish will be pointing in the direction of the satellite. But that almost never happens, so you move the whole motor (and attached dish) slightly left or right to peak the signal. Now, you also have to have the motor elevation/latitude correct (in my case 37 degrees elevation or 53 degrees latitude) and you also will need to tweak the dish elevation where it is attached to the motor.
It would help if you gave a rough idea of your location (nearest town/city).
Here's a photo of my setup. The back wall of my house points exactly south (handy!). The photo shows the dish pointed at 5W which is closest to the top of the dish arc (nearest 0 on the motor).
chris0147 - you line up the dish and motor (set to 0) to point south wherever you are located. So, in the direction of the sun at local noon. Where I am (county Wicklow, south of Dublin)the sun is due south of me right now (12.25ish). If you are on the Greenwich meridian (which runs through London), local noon is at 12.00.
Assuming you have your north/east(or west) coordinates set correctly in the box you then tune to the satellite that is nearest your due south. This is the so-called "top of the arc" or closest to 0 on the motor. If you are in the eastern side of GB, then the 0.8W satellite is your "top of the arc". For someone in west Wales (or for me), then 5W is the top. The box will calculate the angle to the satellite from the location coordinates stored in the box. In my case, the motor will turn a little bit to the east as my motor zero position is at 6W (my longitude). If you were really accurate in lining up due south originally, then the dish will be pointing in the direction of the satellite. But that almost never happens, so you move the whole motor (and attached dish) slightly left or right to peak the signal. Now, you also have to have the motor elevation/latitude correct (in my case 37 degrees elevation or 53 degrees latitude) and you also will need to tweak the dish elevation where it is attached to the motor.
It would help if you gave a rough idea of your location (nearest town/city).
Here's a photo of my setup. The back wall of my house points exactly south (handy!). The photo shows the dish pointed at 5W which is closest to the top of the dish arc (nearest 0 on the motor).
Thanks tony, today I have moved the whole rig to dead straight centre and I have set the motor to 0. When I select on 0.8west channels, it will not move the motor. When I selected on 16 east, it will move the motor to the wrong direction. From what I can see it will move the motor to 2 degree in the west which it is wrong. It should have move it to 2 degree in the east. How I can get the motor to send to the correct direction?
I have put the correct latitude and longitude in the usuals but it still send the motor to the wrong direction. And when it send the motor to the wrong direction, I am getting no signals.
However, when I reset on the motor, I have disconnected the cable from the motor and I have selected on 16east channels then I turned my receiver off. I have reconnected the motor cable to the motor and I have turned my receiver back on. When I turn it back on, it will send the motor to 0 for 16east so when I selected on 0.8west channels, it will move the motor to 2-3 degree in the east and when I selected on 16 east it will move the motor back to 0.
From what I can see on my phone app, the closest one to the dead straight centre is 45 east so do I have to select on 45 east after when I reset on the motor?
If not how I can send the motor to the correct direction to receive the signals?
Do I have to select on 45 east after I disconnect the cable from the motor?
My local is in Dover which is the south-east of kent in the UK.
As you are in the vicinity of Dover, your latitude is 51N and about 1.3E. This is what should be set in your receiver. I don't understand what you mean by dead straight centre is 45 east??? Your dish and motor (set at zero) should be pointing across the English Channel down the west coast of France - ie pointing due south. This is the start position. When you select 0.8W, the motor should turn slightly west. If you select 16E, it should turn east. Look at my photo. With your dish set up like that, it should be pointing at where the sun is at 12:00.
As you are in the vicinity of Dover, your latitude is 51N and about 1.3E. This is what should be set in your receiver. I don't understand what you mean by dead straight centre is 45 east??? Your dish and motor (set at zero) should be pointing across the English Channel down the west coast of France - ie pointing due south. This is the start position. When you select 0.8W, the motor should turn slightly west. If you select 16E, it should turn east. Look at my photo. With your dish set up like that, it should be pointing at where the sun is at 12:00.
Yep, I have already done that but it won't move it to the right direction. What I mean about the dead straight centre is my dish pointed at 45E which is closest to the top of the dish arc when my motorised system is on dead straight centre with the motor is set to 0.
Like you said in your previous posts:
Here's a photo of my setup. The back wall of my house points exactly south (handy!). The photo shows the dish pointed at 5W which is closest to the top of the dish arc (nearest 0 on the motor).
So on mine the closer that my dish pointed to the top of the dish arc which is 45E. Do I have to move the whole rig slightly and then select on 45east to track the arc?
When I select on 0.8west, it will move the dish slightly to the west but I'm getting no signals so do you know what I need to do?
Do I have to press on the manual button of the motor and slightly move the whole rig until I get the signals or what??
linsladeboy
23-02-21, 09:37
Hi Chris, have you set up motor with off set elevation according to your latitude?
Hi Chris, have you set up motor with off set elevation according to your latitude?
Yes I did. Now I need to find the arc so someone said I live in 1.3East as the closest one would be 1.9east so do I have to move the whole rig to 1.9east??
I don't know why you are saying 45E is the top of the arc! The top of the arc for you (and for anyone in the northern hemisphere) is due south. If there was a satellite at 1.3E it would be top of the arc for you. The nearest to the top of the arc is 1.9E or 0.8W. I tuned in 1.9E and most of the channels are encrypted, but there are a few FTA including a music channel Magic. It should be easily receivable by you.
I think you may be misunderstanding about what the top of the arc means. When your motor is at zero it is at the centre of its travel. It can move 50-60 degrees east or west of the centre. As you are close to the Greenwich meridan, you can theoretically receive satellites positioned from 50-60E to about 50-60W. The top of the arc satellite (when the motor is in the middle or zero position) it will be pointing exactly at 1.3E. That is, it would be pointing towards the Sun at 12:00. Due south. The dish should be dead straight on the centre of the rotating motor pole. Swivel the whole motor and dish assembly together on the mounting pole so that it's pointing due south. A photo of your motor rig would be helpful. The motor elevation should be set to 39 degrees (or 51 degrees latitude) on the relevant scale on the side. You will have to tweak the dish elevation and swivel the whole motor/dish assembly to maximise the signal, so it's a two person job - one up the ladder and the other checking the signal quality.
Oh sorry I was confused. I thought the 45east was the closest to the dead centre but I was wrong. My centre satellite is 0.8west so I have moved the whole rig to 0.8west with the motor set to 0. Is that the correct way?
BTW, I have found the issue. When I undo the screw that hold on LNB and I have moved the LNB in so guess what?
I can now receive sport klub 1 hd and some other channels. But I cant get the signals for sport klub 2,3 and some other channels. I tried to adjusted on my dish, motor elevation and usuals but it does nothing.
I think there is a problem with my lnb as it is to too small to move in. Here is my lnb:
https://www.world-of-satellite.co.uk/gt-sat-gt-slrc1-0.1db-universal-single-compact-lnb
Is my lnb that I bought are the wrong one?
I have already bought inverto black ultra 0.2db that I bought it in few months ago but I'm not sure if it would work??
I would think that the inverto would be a better bet. When you say you are undoing the screw of the LNB, I take it that you are trying to move the LNB slightly closer to the dish or away from the dish to get the signal peaked? You should do this and also should try rotating the LNB in the holder to get the skew correct. With a motorised setup, the usual thing to do is get the LNB so the the cable is at 6 o'clock looking at the dish from the front when the motor is at zero. The way the dish motor works means that the LNB will skew as the motor turns. Tune to a weaker channel and rotate the LNB in its holder slightly and move it closer or further out in the holder to maximise the signal quality. A tip to check the dish elevation is to grasp the bottom of the dish and push it down or up and watch the signal quality value. This will give you an indication which way to move the dish elevation bolts. Similarly grasp the left or right side of the dish and push or pull and this will give you an indication which way to move the motor u-bolts on the pole.
I can't find sport klub on 0.8W listings. Are those channels on a different satellite? Some transponders may not be aimed at the UK, so you may not get them.
My centre satellite is 0.8west so I have moved the whole rig to 0.8west with the motor set to 0. Is that the correct way?
This is wrong. 0 is due south. If you are at 1.3 east and you set up 0.8W at zero you will be 2.1º wrong.
You need to set your coordinates in tuner setup and then tell the motor to go to 0.8W. Once the motor is at 0.8W you move the motor around the mast until you find a channel on 0.8W.
I have been telling this guy over on techkings since December and went to private messages I told him not to go on numerous forums posting the same question as all that would do is confuse. I told him to get the inverto lnb after he gave a link for the gsat lnb. He has been told the correct way from day 1. When I told him to change lnb he had the cheek to question whether it was better than the gsat. His house is located in an alcove and will be lucky to get 5w to 36 east.
He is using a technotmate 2600 with an 80cm dish and an octagon sf8008. The initial wall mount was for a fixed dish, a long story, installer set him up on 28east and came back after I told him to get him back and when finished show him how to use receiver, guy came back and set him up on 19east and he never asked him to go to the next sats. He has now fitted an L shaped wall mount but took down motor and dish. I gave him link to you tube video that has the 3 dots to show rig is dead straight and dish is square.
I got him to send me pics, the rig is crooked, the lnb was twisted, the cable from the lnb is all bent, as he wanted 16east I got him to send dish to 16east check on motor TO SHOW IT HAD MOVED then select a channel, he is using his phone with webif to check signal, he got euorsport hd with 72% its H but not sportclub whihc is V got him to adjust focal length and he got sportclub but not a few others. Left him with job to make rig straight, fix new lnb and report back.
With USALS you can use any sat to set up motor due south no longer applies. What does apply is the 3 dots ie rig 100%. You select sat then move whole rig. I hope one day it will click and he gets sorted but as its lockdown I have lots of time.
Just posting to give full picture. I should add getting the full picture is like pulling teeth, when he put up new wall mount he forgot to mention he had the black ultra!! I get a channel name with no sat details.
I hope he manages it as he defenitley has loads of determination.
It explains a lot... I was almost getting to the point of shouting, particularly at the long intervals between replies.
You do need to do initial setup on motor at zero with the whole rig pointing south, though. Then send the motor to your setup satellite and tweak it after that.
I know I told him all that numerous times. It was late when I posted. Have you seen the u tube video that mentions the 3 dots? The image is Openatv 6.4.
In actual fact what he wants is the exact same set up as in your pic as it would push rig out further.
I would think that the inverto would be a better bet. When you say you are undoing the screw of the LNB, I take it that you are trying to move the LNB slightly closer to the dish or away from the dish to get the signal peaked? You should do this and also should try rotating the LNB in the holder to get the skew correct. With a motorised setup, the usual thing to do is get the LNB so the the cable is at 6 o'clock looking at the dish from the front when the motor is at zero. The way the dish motor works means that the LNB will skew as the motor turns. Tune to a weaker channel and rotate the LNB in its holder slightly and move it closer or further out in the holder to maximise the signal quality. A tip to check the dish elevation is to grasp the bottom of the dish and push it down or up and watch the signal quality value. This will give you an indication which way to move the dish elevation bolts. Similarly grasp the left or right side of the dish and push or pull and this will give you an indication which way to move the motor u-bolts on the pole.
I can't find sport klub on 0.8W listings. Are those channels on a different satellite? Some transponders may not be aimed at the UK, so you may not get them.
OK I'm going to change it. Hopefully it will help to resolve the problem.
The sport klub is on 16east satellite. Please check it and let me know.
This is wrong. 0 is due south. If you are at 1.3 east and you set up 0.8W at zero you will be 2.1º wrong.
You need to set your coordinates in tuner setup and then tell the motor to go to 0.8W. Once the motor is at 0.8W you move the motor around the mast until you find a channel on 0.8W.
Ah I see, so if I move the whole rig back to dead centre with the motor 0 due to south, how I can tell the motor to go to 0.8west when I enter the correct coordinates in turner setup?
It sounds like to me I need to reset it in the turner. I have tried to reset the motor but it still don't send to 0.8west. I need your help.
I need your help.Your best bet is to pay a professional to come and do it for you.
I dont think he realises I am holding his hand over on techkings. I wondered why he took ages to get back to me. The good news is that he can now get sats 0/8w to 46 east the bad news is he has asked me again about setting motor to 0. I have loads of spare time. And he has totally confused himself by asking all over the pplace.
Now if wolves could only confuse city:confused:
Your best bet is to pay a professional to come and do it for you.
I don't need to as I can do it myself. Shame that people like you can't be nice to help others to resolve the ongoing problem :thumbsup:
I still can't get the move to move to 0.8west when the whole rig is set to 0 due to south.
When I moved the whole rig to dead straight with the motor set to 0 and when I selected on a channel on 0.8west, the motor won't move. I have done the factory reset on the receiver and I have put the correct latitude and longitude in the usuals.
When I selected on a channel on 0.8west the motor still won't move. I can only get the signals when I move the whole rig from dead straight to 0.8west.
Can I ask how do you get the motor to move to 0.8west when I move the whole rig to dead straight with 0 due to south?
I want to get it done correctly so I can move on.
Post a screengrab of your tuner configuration.
when motor at 0 and you move to 0.8w the dish will not move or just a tiny bit if you have the motor setup about right 0 and 0.8 are less than a degree and has in the post before if you can get music channel with good figures you are just about setup and should be able to pick a good few satellites up. If your mounting pole is not plumb in all directions left/right front/back when the motor and dish are on it you need lots of time up the ladders setting your system up this is the most important thing in any install.
when motor at 0 and you move to 0.8w the dish will not move or just a tiny bit if you have the motor setup about right 0 and 0.8 are less than a degree and has in the post before if you can get music channel with good figures you are just about setup and should be able to pick a good few satellites up. If your mounting pole is not plumb in all directions left/right front/back when the motor and dish are on it you need lots of time up the ladders setting your system up this is the most important thing in any install.
Oh right, so how I can get the dish to move when I setup the rig on dead straight as the motor is 0 due to south?
Do I have to disable usuals, reset the motor, disconnect the cable from the motor, select al jazeera english on 0.8west, turn off power, reconnect the cable to the motor, turn on the receiver, turn on the usuals and select al jazeera english to get the motor moving?
If not can you give me step to step with what I need to do to get the motor moving??
slightly loosen the bolts connecting the motor to the pole and then manually move the motor by hand to the left or right whilst watching the signal strength. Once you have a good signal, tighten the bolts, then you can try adjusting the vertical angle of the dish to see if the signal improves. The movements need to be small.
Then use the receiver to send the dish to another satellite, if the pole is true you should get a signal.
The box talks to the motor via the cable so in the box you need your lat and long inputted and usals switched on and of cause a channel list which is upto date. Thats after the dish is on the motor arm spot on and the motor is on the pole spot on plumb. Then send the dish to 0.8w and the music channel the one thats not encrepyted.
if you do not get a picture then follow this guide. 2 people with a phone each one at the dish motor the other watching the telly. undo the u clamps just so you can move the motor with a bit of effort. slowly in the direction use choose turn the motor very very slowly if the person watching the telly sees a picture tell them to tell the person on the motor to STOP.
Right person on telly then needs to change channel to another clear channel on 0.8w and see if its the correct one or if you have sat finder on your box when its on any channel with a good signal it will tell you which satellite its locked onto if you flick through the transponders and find the strongest one.
Right if the sat finder does not say 0.8w BUT the have a picture and the satellite which you are locked on thats a point which you can start from.
on the box go to a clear channel on the satellite being shown on the sat finder and look which way the motor turns the dish. So if it moves left then you need to move the motor by hand right and visa/versa. Back to where you had a picture and same satellite on the sat finder.
Right now you are roughly setup.
send the dish via the box to the music channel on 0.8w and do the fine tunning as in the other posts on this thread.
If you cannot follow this guide then there is just no hope or just spend a few quid on a good installer in your area someone with a good meter and at least a bit of a cule.
P.S. This has been one hard thread to help out on when all the info and videos are all over the Web some cracking setup videos on Youtube. It helps have a meter for a start even if you can lend one.
read post 15 :confused::confused::confused::confused::confused:
He can now get 0.8w to 42e, but has now gone off on a tangent. I have given up. Obstruction for rest of west.
so if he is setup what his he after :sofahide:im now also at a loss :confused:
Oh right, so how I can get the dish to move when I setup the rig on dead straight as the motor is 0 due to south?
Do I have to disable usuals, reset the motor, disconnect the cable from the motor, select al jazeera english on 0.8west, turn off power, reconnect the cable to the motor, turn on the receiver, turn on the usuals and select al jazeera english to get the motor moving?
If not can you give me step to step with what I need to do to get the motor moving??
chris - can you provide photos of your motor setup when the dish is pointing south (at zero on the motor) and also when it is pointing at 0.8W. Your south (with motor at zero) is 1.3E (as that is your longitude). When you select a channel on 0.8W, the motor will turn 2.1 degrees to the west in order to point at 0.8W. Two degrees on a motor will take less than a second. You would barely notice the turn. As redrobin posted, your adjustments, when needed, will be tiny. In some cases, tightening one side of the motor U-bolt will bring a weak satellite in.
He can get from 0.8w to 42 east, rest of west is blocked. I have given up. By the way he did not even say thanks:mad:
He PM me back in November. All the info given here is exactly what I told him back then.
Yesterday I picked up a secondhand 80cm dish and motor (£30 bargain), in about an hour I had it installed and tracking all sats, using my smart phone.
It’s not that hard.
Sent from my iPad using Tapatalk
I blocked him months ago. He was pestering me by pm and refused to post on the forum instead. He wouldn't pay for a proper T & K then. And he still hasn't the dish sorted.
Damn, I'd forgotten that I tried to help him on the other thread and suggested a proper pair of T&K brackets. There's no hope of getting the arc tracking consistent using a fixed dish bracket like he has - galvanised or not. I'm out:zoom:
He PM me back in November. All the info given here is exactly what I told him back then.
Yesterday I picked up a secondhand 80cm dish and motor (£30 bargain), in about an hour I had it installed and tracking all sats, using my smart phone.
It’s not that hard.
Sent from my iPad using Tapatalk
It might be not that hard for you but it is hard for me to get the rig on dead straight. I tried to get the dish to move when I select on any sats so it won't move.
I don't know how you do that, but did you turned off usuals and disconnected the cable from the motor before you move the rig to dead straight?
And did you reset on the motor?
It might be not that hard for you but it is hard for me to get the rig on dead straight. I tried to get the dish to move when I select on any sats so it won't move.
I don't know how you do that, but did you turned off usuals and disconnected the cable from the motor before you move the rig to dead straight?
And did you reset on the motor?Which is why I suggested you get a professional.
Chris you told me this on PM's " Yes the dish does move when I select 16east but I'm trying to get the rig on dead straight but at the moment I have moved the rig to 0.8west."
That is correct by the way. So give over and watch tv.
stargateuser
17-05-21, 20:01
I have had no end of fun explaining to different people that 28e is not 28e in the sky, it is 28e at the EQUATOR not 28degs east of North when dialled on a compass. That is the hardest thing that people have to get to grips with, once the penny drops you see them go "Ah ha!" I have an old sat slide (ex-military one) and use that to explain.
I didn't know about the USALS being able to be set up on any sat, the only issue with that would be setting the LNB skew, which if set on 0.8w would be spot on :cool:
I have had no end of fun explaining to different people that 28e is not 28e in the sky, it is 28e at the EQUATOR not 28degs east of North when dialled on a compass. That is the hardest thing that people have to get to grips with, once the penny drops you see them go "Ah ha!" I have an old sat slide (ex-military one) and use that to explain.
I didn't know about the USALS being able to be set up on any sat, the only issue with that would be setting the LNB skew, which if set on 0.8w would be spot on :cool:
On a motorised system you would normally set the LNB straight in the holder (no skew). The cable(s) from the LNB would be at six o'clock when the dish was pointing at your southernmost satellite. If you are in east or central England, this would be 0.8w. In my case the southernmost satellite is 5W. As the motor turns, the dish and LNB will skew automatically to the correct angle for different satellites east or west of your location. The satellite position of the Astra satellites (28.2E) would locate them directly overhead the Democratic Republic of Congo. For someone near Istanbul in Turkey 28.2E would be their southernmost satellite, for example.
chris0147 - you line up the dish and motor (set to 0) to point south wherever you are located. So, in the direction of the sun at local noon. Where I am (county Wicklow, south of Dublin)the sun is due south of me right now (12.25ish). If you are on the Greenwich meridian (which runs through London), local noon is at 12.00.
Assuming you have your north/east(or west) coordinates set correctly in the box you then tune to the satellite that is nearest your due south. This is the so-called "top of the arc" or closest to 0 on the motor. If you are in the eastern side of GB, then the 0.8W satellite is your "top of the arc". For someone in west Wales (or for me), then 5W is the top. The box will calculate the angle to the satellite from the location coordinates stored in the box. In my case, the motor will turn a little bit to the east as my motor zero position is at 6W (my longitude). If you were really accurate in lining up due south originally, then the dish will be pointing in the direction of the satellite. But that almost never happens, so you move the whole motor (and attached dish) slightly left or right to peak the signal. Now, you also have to have the motor elevation/latitude correct (in my case 37 degrees elevation or 53 degrees latitude) and you also will need to tweak the dish elevation where it is attached to the motor.
It would help if you gave a rough idea of your location (nearest town/city).
Here's a photo of my setup. The back wall of my house points exactly south (handy!). The photo shows the dish pointed at 5W which is closest to the top of the dish arc (nearest 0 on the motor).
Hi sorry to jump in, out of interest if may ask a question about your pole mount setup please for my knowledge and understanding?
How did you manage to get your pole dead straight on the wall, is there an acceptable tollerance acuracy +/-? or is it 100% when measured electronically or just sprit bubble centred ?
Did you have to use packing shims on the fixings to get it dead straight 100%?
Im only asking because no wall is 100% vertical and wanted know how the adjustmenst was made as i know geting it right electronically straight is hard work.
However, I do like your setup
abu baniaz
22-02-22, 18:02
This is why it was suggested over and over again on several forums for the OP to use T & K brackets. You can then adjust and ensure the pole is plumb.
Edit: This is/was the picture of his dish
https://www.world-of-satellite.com/showthread.php?63580-Missing-satellite-channels-on-search&p=505623&viewfull=1#post505623
I agree with Abu. If you must mount a motorised dish on a wall, use T and K brackets. At least a 50mm pole. And preferably the motor between the brackets. And there is no tolerence. Get it straight.
I agree with Abu. If you must mount a motorised dish on a wall, use T and K brackets. At least a 50mm pole. And preferably the motor between the brackets. And there is no tolerence. Get it straight.
Thankyou that helps
Sorry - only seeing this now. The T&K brackets have elliptical mounting holes, so you can "nudge" the brackets slightly to get the pole vertical in all directions before final tightening. You can use an inclinometer or spirit level to ensure the pole is vertical. If you have a smart phone you can get a level app which will be accurate to the nearest degree. This is also useful for checking that the motor angle is correct for your latitude.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.