Manual & Auto Scan Menu Disappeared

[rido111]

Hi

I open Setup —> Tuner Config menu but i cannot see Manual and Auto Scan menu. Only the items listed below are seen:
Tuner Setup
Miscellaneous
AutoBouquetsMaker
Blind Scan
Fallback Configuration

How can enable or find Manual or Auto Scan menu item?

[abu baniaz]

What tuner config have you set?

Sent from my Moto G (5S) using Forum Fiend v1.3.3.

[rido111]

How can i find what the tuner config set? Could you please help me to answer your question? From where, i can see what tuner config have set?

[abu baniaz]

go into tuner setup.

Sent from my Moto G (5S) using Forum Fiend v1.3.3.

[rido111]

56994u

I attached that.

[abu baniaz]

We'll have to look into this. There was a change so that those menus do not show if tuners are not set. You can't scan if tuners are not set. Yours are set.

Can you try a restart?

Sent from my Moto G (5S) using Forum Fiend v1.3.3.

[rido111]

I have tried that nothing changed.

[rido111]

I understood that you will look into this. Could you please tell me when you fix that? Thanks.

[abu baniaz]

Can you enable debug logs and restart GUI to activate.
Go into the tuner config menu.
Save debug log to PC and attach here


Can you also run this command. A file called mytunerconfig.txt will be created in /tmp/ directory. Attach it here too. Guide in my signature if you need it. You may want to have a look at the screenshots guide too



cat /etc/enigma2/settings | grep config.Nims > /tmp/mytunerconfig.txt

[rido111]

Hi,

I attached debug log file and mytunerconfig.txt file.

[abu baniaz]

Tuner 1, port C, this is still set to automatic(auto diseqc). Please set it to a satellite.

Tuner 2. This is still not set. Set it as not configured please. Restart using menus and the try again.

[rido111]

Hi

I have set a satelitte to port c of tuner 1 and also set “not configured” to tuner 2. After reboot, nothing changed, i have not seen the menus yet.

57007

[Andy_Hazza]

Be quicker just to reflash the receiver with the latest image.


Sent from my iPhone using Tapatalk

[abu baniaz]

Sorry to ask, are you rebooting by remote control or using switch at the back?

[rido111]

Ohh, it is very difficult for me. Because i have many customization, settings and plugins. Any shortway for this or will you fix this problem?

[rido111]

By remote control

[abu baniaz]

Can you attach your settings file please? It will be in /etc/enigma2 You will need to zip before you can attach it.

Can you also check that the setup mode is the default (expert)?
Menu > Setup > System > Customise

Just for reference purposes, the change was was here.
https://github.com/OpenViX/enigma2/commit/3f657851d7c7d1a48c012990df65d0bbb2c8cf9f

[rido111]

Setup mode is expert. I could not understand that why you need my settings?

Is it bug or not, any opinion?

[abu baniaz]

The commit/change is that if tuners are not configured, those two menus will not show. It is not a bug as far as we know. Nobody else has reported the issue.

You said your tuners were configured/set correctly, that file you posted showed otherwise. However, it is a trimmed version of your settings file.

Maybe you should flash image again, do not restore anything after flashing, set your tuners and then try again?

[rido111]

Maybe the other users havent yet updated or not recognized. I control updates every time and update when you publish it. So the others may not recognize this problem. Could you check what you checked in the latest change. By the way i am software developer for 15 years. So i understand you but i advice check the code again one more time. Thanks.

[Andy_Hazza]

Maybe the other users havent yet updated or not recognized. I control updates every time and update when you publish it. So the others may not recognize this problem. Could you check what you checked in the latest change. By the way i am software developer for 15 years. So i understand you but i advice check the code again one more time. Thanks.

No issues here on various boxes.


Sent from my iPhone using Tapatalk

[Andy_Hazza]

You will just have to bite the bullet and reflash with latest ViX image and do as Abu says, setup from scratch with no restores of your backup/plugins.


Sent from my iPhone using Tapatalk

[ccs]

…. even easier if you do an image backup first, then you can do as asked and then go back to your original image if you want/need to.

[rido111]

ok i understood you but in previous version i did not have a problem like that, so i believe that this is a problem of last commit. After reflash my image if the problem continues, what will you advice or do?

[abu baniaz]

To fix a problem, you have to be able to reproduce it/know cause. As far as we know it is working fine. Commit is from PLi, nobody has reported issue there either.

I am on 5.1 030 003. I also flashed 5.1 029 to test your report. I could not reproduce the issue you are having.

Sent from my Moto G (5S) using Forum Fiend v1.3.3.

[abu baniaz]

After reflash my image if the problem continues, what will you advice or do?



Will come round for tea and see issue myself.



Please create an image backup so you can restore it if necessary. Flash new image, do not restore anything or install any plugins. Just set tuners and check menus.



Sent from my Moto G (5S) using Forum Fiend v1.3.3.

[rido111]

I have flashed 5.1.029 and not restore or install anything but my problem continues. Menus not visible.
Tuner 1 is set and only Port D is set, the others not connnected and tuner 2 is disabled.

[abu baniaz]

As you are not willing to upload your settings file, I am out of ideas.

Here is mine



Sent from my Moto G (5S) using Forum Fiend v1.3.3.

[rido111]

i have attached settings (after flashing new image)57009

[rido111]

i have also attached latest tuner config screen shots. any opinion?
57010
57011
57012

[abu baniaz]

i have also attached latest tuner config screen shots. any opinion?


Those are inconclusive. Attach the file please. There is nothing personal in them, you have just flashed a new image anyway. Read the file first if you are in doubt.

I suspect it is the automatic diseqc setting.

[rido111]

which file? i have attached setting file.

[rido111]

did you checked settings file.

[abu baniaz]

Please try the following settings file. Ignore the 28.2 for now.

Issue "init 4" command first
Unzip the attached settings file
Transfer it to /etc/enigma2
Issue an "init 3" command to restart

[rido111]

i have changed settings file as you told but nothing changed.

[abu baniaz]

I will have to refer to someone more knowledgable.

[rido111]

as i said before it is bug. Developers must look for it. Previous version did not have this problem.

[rido111]

who will look for it? when will be fixed, i cannot scan any channel because of that

[abu baniaz]

You can look for it too. You have been a software developer for 15 years. We are people who do this for a hobby in our free time. I have posted a link to the changed files, you can undo the changes on your current system as a temporary measure.

[rido111]

I told you that i am a software developer for impressing to understand you easily what you have been telling to me. I think it should not be easy like that "undo changes as a temporary measure". If you are senior, you have to look for a stable solution. I did not write any code with phyton so i do not know how to code it. I looked for the changes but i could not get any point. But i feel that it is very basic bug you can find. I have 2 tuner and one of them is disabled. I think that is the first reason for that.

In brief, is there any investigation for this problem, how can we solve this?

[abu baniaz]

You are the only one with the problem. It will be fixed or changes undone.

Stop being pushy.

[rido111]

ok thank you.

[ronand]

Ok guys. I can reproduce this on my Solo2. Tuner A is a motorised dish (USALS), Tuner B is Second cable of motorised LNB, Tuner C is an RTL-SDR dongle on the USB port (DVB-T). If Tuner B is set as not configured then the menu items disappear. I dont think Tuner C has any effect on the issue. I would suggest that rido111 configure tuner B as equal to A (just to give it a configuration for testing).

[ronand]

The issue seems to have crept into version .028

[Huevos]

Obviously a driver issue.

Attach the dish cable to tuner B.
Setup tuner B.
Set tuner A to not configured.

[ronand]

Using Tuner B with A not configured works fine. It all works fine in .027 but that should be a workaround for the moment for the OP.

[Huevos]

Reason for this on the Solo2 is because it is internally connectable B to A, but not A to B. So Solo2 should always use tuner B as the main option when only one tuner is configured or the box is configured with one tuner as a slave.

[ronand]

That is true that there is an internal loopthrough but in .027 and earlier versions it didn't matter which tuner was configured - it worked.

[Huevos]

That is true that there is an internal loopthrough but in .027 and earlier versions it didn't matter which tuner was configured - it worked.The driver/hardware bug was always there with the Solo2, it is just that this commit shows the bug.

This other commit was added as a workaround for the same bug on a Solo2 some time ago. https://github.com/OpenPLi/enigma2/commit/57ed8cc9b2824dfa7342404cc00c164578c0f0df#diff-021996494dde61d73519d0ab55099cb4

[ronand]

OK. thanks for the info.

[abu baniaz]

Can affected persons do the following for debugging purposes:

Ensure debug logs are on, GUI restart is required to activate them. We will be restarting at end of next stage, so hold on for this.

In the followoing directory, /usr/lib/enigma2/python/Components
Rename NimManager.pyo to NimManager.pyo.original

Transfer the attached file to /usr/lib/enigma2/python/Components
Leave the ftp client open

Restart the receiver
Go into the tuner config menu

In the followoing directory, /usr/lib/enigma2/python/Components
Ensure you have NimManager.pyo and NimManager.pyo.original (you may need to refresh FTP client)
Delete NimManager.py

Please attach debug log to this thread

[rido111]

Hi

this solution will be released as an update?

[ccs]

Hi

this solution will be released as an update?Debug log??

[Huevos]

Hi

this solution will be released as an update?Didn't you say you were a software developer? You were supposed to run the file and post the debug log.

[Bonus101]

Hi, I have the same Tuner config menu after factory reset and flashing the latest image to my Gigablue HD Quad plus. My Mutant HD51 is still with the full Tuner config menu.

[Bonus101]

I tried the debugging and have attached the logs as requested.

regards,

[Huevos]

This has already been fixed. Update will be in build 031.