Setup 23.5°E, 19.2°E, 13°E with DiSEqC 2.0 switch S4/1PCN-W1 running OpenViX

[3Dready]

I would like to set up Ultimo4K with latest OpenViX on it with 1 in-feed that has DiSEqC 2.0 switch S4/1PCN-W1 and 3 LBN's pointing to 23.5°E, 19.2°E, 13°E.

The recommended setup for Sky UK worked great with AutoBouquetsMaker,
but the "AutoBouquetsMaker" is only limited to few satelites and 23.5°E, 19.2°E, 13°E are not there ...

[abu baniaz]

AutoBouquetsMaker (ABM) does not "scan" satellites, it "scans" providers. It will only offer you the providers that you can receive. It checks your tuner configuration and does not show the ones you cannot receive.

[3Dready]

I see, so forgot to set-up the tuner .......



My settings are switch S4/1PCN-W1:
Port A: 19.2E Astra 1KR/1L/1M/1N
Port B: 23.5E Astra 3B
Port C: 13.0E Eutelsat Hot Bird 13B/13C/13E


So I have setup in: 1 Setup - 2 Tuner config - 1 Tuner setup - Tuner I Vuplus DVB-S NIM (45208 FBC) (DVB-S2):

Configuration mode: simple
Mode: DiSEqC A/B/C/D
Port A: 19.2E Astra 1KR/1L/1M/1N
Port B: 23.5E Astra 3B
Port C: 13.0E Eutelsat Hot Bird 13B/13C/13E
Port D: nothing connected
Set voltage and 22KHz: yes
Send DiSEqC only on satellite change: yes
Force Legacy Signal Stats: yes
[green] to Save

Then go to: 1 Setup - 2 Tuner config - 1 Tuner setup - 7 Signal finder
Tuner: Tuner I Vuplus DVB-S NIM (45208 FBC) (DVB-S2)

Satelite: 19.2E Astra 1KR/1L/1M/1N
Tune: predefined transponder
Transponder: 10714 H 22000 2/3
Scan: will find 6 channels, Mainfranken HD, Franken Fernsehen HD, TVA-OTA HD, ..........


So change to:
Satellite: 23.5E Astra 3B
Tune: predefined transponder
Transponder: 11644 H 5500 3/4
Scan: will find 60 channels 2040 - ESKA Gorzow, 2050 ESKA Kielce .....


Then change to
Satellite: 13.0E Eutelsat Hot Bird 13B/13C/13E
Tune: predefined transponder
Transponder: 10719 V 27000 3/4
And nothing ........ I can not get the Ultimo4K to tune to 13.0E Eutelsat Hot Bird on port C or (IN3) on switch .....



I am using DiSEqC 2.0 4x1 weatherproof switch S4/1PCN-W1 from:
https://www.ebay.com/itm/DiSEqC-2-0-4x1-weatherproof-switch-S4-1PCN-W1-4-YEARS-WARRANTY-Made-in-EU-/251777994505

[abu baniaz]

Do you want to scan the three satellites?

[3Dready]

Yes, all at once.

Or should I scan them individually?

[abu baniaz]

Always best to say what you want to do/achieve as well as what you are doing.

In manual scan, select the tuner that is configured/set to receive the satellites you want to scan.

Type of scan: multisat.

Enable the sats you want to scan. Press Green when ready.

[3Dready]

[SOLVED]


I have restored settings to default, then set the tuners and ports again for the switch and all working now.