DVD-c not working since 5.14

[lynd145]

I did update on duo 2 to 5.14 last night and get no picture on dvb-c tuner now is there a problem with update thanks

[bsod]

I did update on duo 2 to 5.14 last night and get no picture on dvb-c tuner now is there a problem with update thanks

it may be related to the issue discussed in this thread.

http://www.world-of-satellite.com/showthread.php?56802-DVB-T-broken-after-upgrade-to-5-0-014

So far no info back from the devs on this, but it is early days yet. Do you have a VU+ branded system or something else? Knowing this may help the devs track down the issue if it is only affecting a particular brand/model. So far the only two reports (apart from yours) are for VU+ DUO2 systems. Basically the more info we can provide upfront the more benificial it will be for the devs to look into.

Regards,

Craig

[lynd145]

Put back to 5.0.013 till there is a fix and working ok

[thisntaht]

Same issue here on a VU+ Duo2, Reverted back to 5.0.013 and all fine again.

[Huevos]

It is a driver issue reported to Vu+.

Flash and restore. Don't update.

[Bangord30]

My duo2 cable is fine on .14?!

Sent from my HUAWEI VNS-L31 using Tapatalk

[ccs]

My duo2 cable is fine on .14?!Are you using twin tuner modules?

http://www.world-of-satellite.com/showthread.php?56829-Problem-with-5-0-014-update

[Bangord30]

1 Sat, 1 cable. Online updated.

Sent from my HUAWEI VNS-L31 using Tapatalk

[grahammcm1888]

Aghhhhh annoying. I am in the process of rolling back to .13 to try and fix the issue :baby:

[abu baniaz]

Aghhhhh annoying. I am in the process of rolling back to .13 to try and fix the issue :baby:

You don't need to use an older image.

Flash 014. Problem only occurs if you update to 014.

To avoid confusion....

Update = Menu > Setup > Software Update
Flash/Install = Use USB stick or Image Manager to install/restore newer image

[abu baniaz]

1 Sat, 1 cable. Online updated.

Sent from my HUAWEI VNS-L31 using Tapatalk

Twin tuner modules or single tuner modules?

[Bangord30]

Oh sorry single modules

Sent from my HUAWEI VNS-L31 using Tapatalk

[abu baniaz]

Issue affects twin tuner modules.

I have put a message stating:



If you have a twin tuner card, do not perform an online update to 014.

You should flash/install 014 instead.

[grahammcm1888]

You don't need to use an older image.

Flash 014. Problem only occurs if you update to 014.

To avoid confusion....

Update = Menu > Setup > Software Update
Flash/Install = Use USB stick or Image Manager to install/restore newer image

Gotcha , I will give it a go :)

[grahammcm1888]

Yeah , confirmed working ok after flash. I have a dual tuner on my VU Duo 2 so I guess that was the problem.

[bellejt]

did a couch flash and restore and fine.

[Timmo65]

Hello,
I have a duo2 with twin sat (input A+B) and twin cable tuners Nim TT3L10 (C+D). The cable tuner was added recently and I was having a lot of problems getting a signal at all. I eventually stumbled on this thread ... https://forums.openpli.org/topic/49214-vuplus-duo2-dvb-t2-tuner-nim-tt3l10-stopped-working/ which gave me the interim fix - I ran the 2 echo commands to add C and D tuners to inputs 2 and 3 and they immediately came back. At this point I was on openvix 5.0.014 and had not seen this thread. I reflashed 014 and all looked good (no need for the manual fix and the tuners were kept after reboot). Today I online updated to 016 and my dvb-c tuners have gone again - no signal - unable to tune. From checking the folders it looks like settings have been changed to accommodate another 4 tuners (EFGH) but I'm not sure the other settings around choices and CIO CI1 look ok. Can someone please advise if there is still a know problem with this or if its my set up and should I reflash.

Here are the tuner assignment settings I have after 016 update...


root@vuduo2:~# grep -r "" /proc/stb/tsmux/
/proc/stb/tsmux/input7_choices:CI0 CI1 A B C D E F G H
/proc/stb/tsmux/input6_choices:CI0 CI1 A B C D E F G H
/proc/stb/tsmux/input5_choices:CI0 CI1 A B C D E F G H
/proc/stb/tsmux/input4_choices:CI0 CI1 A B C D E F G H
/proc/stb/tsmux/input3_choices:CI0 CI1 A B C D E F G H
/proc/stb/tsmux/input2_choices:CI0 CI1 A B C D E F G H
/proc/stb/tsmux/input1_choices:CI0 CI1 A B C D E F G H
/proc/stb/tsmux/input0_choices:CI0 CI1 A B C D E F G H
/proc/stb/tsmux/input7:H
/proc/stb/tsmux/input6:G
/proc/stb/tsmux/input5:F
/proc/stb/tsmux/input4:E
/proc/stb/tsmux/input3:D
/proc/stb/tsmux/input2:C
/proc/stb/tsmux/input1:B
/proc/stb/tsmux/input0:A
/proc/stb/tsmux/ci1_tsclk_choices:normal high
/proc/stb/tsmux/ci0_tsclk_choices:normal high
/proc/stb/tsmux/ci1_tsclk:high
/proc/stb/tsmux/ci0_tsclk:high
/proc/stb/tsmux/ci1_input_choices:CI0 A B
/proc/stb/tsmux/ci0_input_choices:CI1 A B
/proc/stb/tsmux/ci1_input:A
/proc/stb/tsmux/ci0_input:A


Thanks

[Andy_Hazza]

You need to flash via usb or couch flash (image manager) and restore your settings and should be fine. You can't do the usual update, thus why you still have the issue.


Sent from my iPhone using Tapatalk

[Timmo65]

Hi,
Thanks for that, I was on 014 (from before I got the new tuner and that was via an online update) I then reflashed from image manager and restored settings for 014 when I saw the problem and read this thread. Today I just did an online update to 016, so are you saying I need to reflash 016 via image manager again? What about future updates ?
Thanks

[abu baniaz]

our current expectation is that if you flash 014 and then update to 016, the workaround script will work.

[Timmo65]

Hi, Thanks
OK, that is what I did.
I can try reflashing to 016 rather than an update or/and going back to 014. Do those settings I posted look how they are expected to look ?

[abu baniaz]

We will need to look at script again. For time being, flash 016 and restore settings and plugins.

[Timmo65]

Hi,
Thanks for the help. I reflashed 016 again and the tuners are back. It was odd though as they did not come back immediately, they just reappeared some time later. The tsmux settings appear to be the same as I first posted too. Perhaps the script is ok.