Tuning Failed Fatal Error

[khan888]

Hi

I've just installed a new Diseqc switch for my two dishes...28.2E and 19.2E. I have tried to scan sky Deutschland, Movistar+ and others using AutoBouquetMaker (ABM) but I keep getting a tuning failed fatal error. The 19.2E dish is ok because I can do a manual scan and it picks up all channels.

This is on a Octagon SF4008 using Openvix 5.0.013

Cheers

5353653537

[abu baniaz]

You probably can't lock onto one of the frequencies. Don't know which one, your debug will show it.

[sweto]

when go to scan page check which tuner is selected. must be tuner b secelcted

[abu baniaz]

http://www.world-of-satellite.com/showthread.php?44783-Requirements-for-ABM-support-questions

[khan888]

You probably can't lock onto one of the frequencies. Don't know which one, your debug will show it.

Hopefully I've done the attached log correctly

[abu baniaz]

In signal finder check if you get a lock on predefined transponder on 19.2E, 12032, Horizontal, 27500 9/10

Post a screenshot of signal finder screen please.

[khan888]

In signal finder check if you get a lock on predefined transponder on 19.2E, 12032, Horizontal, 27500 9/10

Post a screenshot of signal finder screen please.

I only get transponder on 19.2E, 12031, Horizontal, 27500 9/10

53540

[abu baniaz]

you need to tweak your alignment.

[khan888]

you need to tweak your alignment.

Ok ill do it tomorrow and report back. Thanks for the help


Sent from my iPhone using Tapatalk

[khan888]

Now I'm getting cannot read data error. I'm using a old sky dish and getting the best possible signal. Is this still an alignment issue or worth replacing the old dish


Sent from my iPhone using Tapatalk

[khan888]

Just to add fastscan Deutschland scanning ok


Sent from my iPhone using Tapatalk

[khan888]

Can anyone shed any light on this, I've put up a new 80cm dish. I'm picking up over a thousand channels but autobouquets is the same.

I've got the best possible signal I can..I think

Thanks


Sent from my iPhone using Tapatalk

[abu baniaz]

21% AGC is not adequate.

[khan888]

21% AGC is not adequate.

Ok thanks, would you know which transponder is best to fine tune my dish too?

Cheers


Sent from my iPhone using Tapatalk

[abu baniaz]

Since you are struggling to lock on this one, that may be as good as any other.

[khan888]

Since you are struggling to lock on this one, that may be as good as any other.

Ok I'll give it another go tomorrow


Sent from my iPhone using Tapatalk

[khan888]

I've improved the signal strength but the quality is still poor I've tried everything.

My meter is giving me a good signal strength and quality but the receiver tells me different.

Also can the signal levels cause the box to lockup on certain channels?

Cheers


Sent from my iPhone using Tapatalk

[abu baniaz]

Can you view Sky Select on that TP without any breakup?

Are you connecting meter at by Dish or where receiver is?

[khan888]

Can you view Sky Select on that TP without any breakup?

Are you connecting meter at by Dish or where receiver is?

I've had sky select on for a few minutes now and not a single breakup.

I had it connected at the lnb but tried at the receiver end and still get the same strong signal levels as I was at the lnb


Sent from my iPhone using Tapatalk

[abu baniaz]

Quality or strength?

[khan888]

This is on transponder 12032

At LNB - signal strength 86% quality 75%

Cable at receiver - signal strength 84% quality 71%

Reading on receiver - signal strength 74% quality 21%


Sent from my iPhone using Tapatalk

[abu baniaz]

Can yo post a screenshot showing 2nd info bar please?

[khan888]

Can yo post a screenshot showing 2nd info bar please?

Screenshot of 2nd info bar

53597

[khan888]

Fresh flash with no settings/plugins and on a automatic scan i'm getting a different signal strength/quality on sky select. Also the channels have stopped locking up, would this be my custom bouquets?

53599

[khan888]

Can someone help me out on this please.

Octagon sf4008 I'm getting tuning failed fatal whilst scanning sky Deutschland in ABM

Edision mini is scanning fine and channels working, signal strength 91% signal quality 90%.

Both using the same dish and same cable coming from the lnb.




Sent from my iPhone using Tapatalk

[Huevos]

Unzip the attached file.
Contains a file called main.pyo.
Place that file in /usr/lib/enigma2/python/Plugins/SystemPlugins/AutoBouquetsMaker/scanner
Restart the box.
Scan Sky DE again.

[khan888]

Unzip the attached file.
Contains a file called main.pyo.
Place that file in /usr/lib/enigma2/python/Plugins/SystemPlugins/AutoBouquetsMaker/scanner
Restart the box.
Scan Sky DE again.

Thanks very much for this Huevos it's working perfect, was on the verge of giving up.

Appreciate everyone's help on this.


Sent from my iPhone using Tapatalk

[junaidh997]

Hi, I have the same problem on a h2h using cable. If I use the attached zip file, will it sort the problem. Abm says tuning virgin uk then says failed to lock onto frequency.

Sent from my ONEPLUS A3003 using Tapatalk

[PhilipM3]

Khan888.
I had this error setting up a box recently when running ABM for the first time. For me it was because I had a tuner enabled ie configured ie I had set Tuner B to be like Tuner A when there was no physical cable attached to that tuner input at the back of the box.
I set it to "not configured" - problem solved.
My setup is similar to your with a disecq switch bringing together 28.2E and 19.2E but that is I believe academic.
If you do have a cable attached maybe the settings are switch wise or otherwise that "effectively" there is no cable there ie that tuner cannot see a LNB to tune to and so ABM gives the error.

[Andy_Hazza]

Hi, I have the same problem on a h2h using cable. If I use the attached zip file, will it sort the problem. Abm says tuning virgin uk then says failed to lock onto frequency.

Sent from my ONEPLUS A3003 using Tapatalk

You need to reread the forum rules you signed up to.


Sent from my iPhone using Tapatalk