Network issues when Zero is on

[CS10]

Hi All,

I've got a network issue when switching on my Zero box.
I have connected it via Wireless Adapter, and it has picked up an IP address correctly etc.

I also have a Solo2 on the same network.

The solo2 has the IP ending 59 and the Zero is 206.

I have installed MGCAMD 1.38 r5 and version 3.2 build 037 of OpenVix installed.

As soon as I turn the box on, the Solo2 box struggles and my sky subscribed channels freeze all of the time, and the same on the Zero.

Can anyone suggest anything?
As soon as the Zero is switched off (not just left in standby), the solo2 works fine - no freezing.

[ronand]

You could have searched the forum for mgcamd problems caused by downloading someone elses config file without checking the contents. You are DDOSing yourself by logging to a non-existant ip address. Check the config file and change the L value to 00.

[CS10]

Hi there,
Thanks for the reply.

My config file already has L value set to 00.

Full contents:

# EMM messages
# 00 dont show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }

# ECM messages
# 00 dont show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 01 }

# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 }

# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
G: { 33 }

# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 }

# network ecm timeout in seconds
K: { 07 }

# newcamd dead routes connect retry, sec
Q: { 10 }

# network shares priority
# 00 gbox, newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd, gbox
# 02 newcamd, camd3, gbox, radegast
P: { 02 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 }

# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 11 } 80

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 00 }

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }

# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 04 }

# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
B: { 06 }

# Mapping 18xx
# 00 disable mapping
# 01 map 18xx to 1801

[ccs]

Is the very last line missing?

[CS10]

WHat should the last line be?

[ccs]

It's F: as far as I can tell (from searching), I found a reference to a default value of 01, but I'm only guessing.

[CS10]

Both of my Vu boxes use the very same cfg file, so if it is missing, its missing on both.

[ronand]

You hardly are running the same line on both boxes? If you are I would imagine the thread being closed very quickly.

[CS10]

You hardly are running the same line on both boxes? If you are I would imagine the thread being closed very quickly.

I was under the impression this is OK if I have sky multiroom?

Am I wrong?

[ronand]

You don't even have a sky subscription ffs.

[abu baniaz]

Forum rules:
http://www.world-of-satellite.com/showthread.php?2-Please-read-the-rules-here

4a. NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN!