MGCAMD 1.35 Partially working on TM NANO SE.

[Nick1969]

Hi,

Reinstalled image (image prior to the latest release) and then loaded MGcamd from plugins.

I notice that only one movie channel will play. The remainder are black screen.

Could Mgcamd be corrupt? Am i better off installing through ipk file?

All FTA are fine. My other box is fine (uses same Mgcamd stuff).

Any advise appreciated!

N

[Willmoore]

Try Mgcamd 1.38

[john doe]

most of time the mg_cfg file it setup wrong. 1.35 and 1.38 all work fine on new image.

[Nick1969]

Hi, Thanks for the replies.

Do you have any suggestions/config files that you know work ok??

[Willmoore]

The issue with the config file usually has a ddos-ing effect but that does not seem to be your issue. You could check the file if you wish (you never know) check Line L it should read {00} anything else is incorrect.

[Bazzer]

Check these files with the ones you are using.
# EMM messages
# 00 dont show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }

# ECM messages
# 00 dont show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 01 }

# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 }

# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
G: { 33 }

# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 }

# network ecm timeout in seconds
K: { 07 }

# newcamd dead routes connect retry, sec
Q: { 10 }

# network shares priority
# 00 gbox, newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd, gbox
# 02 newcamd, camd3, gbox, radegast
P: { 02 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 }

# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 11 } 80

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 00 }

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }

# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 04 }

# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
B: { 06 }

# Mapping 18xx
# 00 disable mapping
# 01 map 18xx to 1801

[Nick1969]

Thanks. I'll try it tonight.

NIck

[john doe]

also if you look on this forum I believe that one of the admins had added the files, which you can check against the one you have

[imish]

is there any point in "tweaking" any of these parameters for services other than Sat?

[john doe]

is there any point in "tweaking" any of these parameters for services other than Sat?

you said that some channels were nor clearing. this is either down to your mgcamd setup, or you need to reinstall the vix image and try again

[Bazzer]

is there any point in "tweaking" any of these parameters for services other than Sat?

No point what so ever works perfectly on 1.35 and 1.38 :confused:

[Nick1969]

HI, Reinstalled latest image and MGcamd. All working fine with my previous Config files.
Image must have been corrupted somewhere down the line!

Thanks everyone for all your comments. Much appreciated!

[joseph1972]

When was this new image released?

Sent from my SM-N9005 using Tapatalk

[john doe]

When was this new image released?

Sent from my SM-N9005 using Tapatalk

ages ago:confused: