View Full Version : cccam not working on vix 1.3
Hi there,
I just cannot get cccam working ony my vu+ duo with the vix image 1.3
I've installed it fine by holding long blue then short green etc...
Also activated cccam 2.1.4 too and I have copied my cfg file to /etc.
Can anyone help?
Thanks
silverfox0786
21-12-10, 00:50
what i suspect your issue is is what is not allowed to be disscussed here
as stated in Rule 3 of the rules here
http://www.vuplus-support.co.uk/showthread.php?2-Please-read-the-rules-here
Hi Silverfox,
Yes I saw the rule number 3:
"3. Emulator config's can be discussed ONLY on a basic config F,C & N line level, i.e help setting up your CCcam.cfg. No promoting of cardsharing rings."
I thought I would be ok to discuss as it is on basic level in setting up CCcam.cfg and I am not promoting any of the cs rings at all.
hope this is ok.
thanks
we will help you install CCcam. we will help you create a CCcam.cfg file and show you where it goes but thats about as far as it goes. we will not and can not help you in any other aspect of the config file as it is a direct breach of the rules.
Hi Pheonix,
Any help would be good. Does the cfg file have to go in the /etc folder?
I have copied my cfg file from my old dreambox. Would that cfg file be correct to use?
Thanks
silverfox0786
21-12-10, 02:04
yes you can use that and pop it into the etc folder as mentioned by pheonix
hmm. thats what I have done from the start and deleted and tried again but just wont work. I dont know what i may have done wrong.....
silverfox0786
21-12-10, 02:15
hmm. thats what I have done from the start and deleted and tried again but just wont work. I dont know what i may have done wrong.....
it should work have you started your softcam in softcam manager
and performed a full software update
I sure have. Can't get my head around this... May to a reflash from usb and start again fwiw.
it should work have you started your softcam in softcam manager
and performed a full software update
silverfox0786
21-12-10, 02:41
I sure have. Can't get my head around this... May to a reflash from usb and start again fwiw.
possibly a reflash may fix it
as what your saying seems to me that your not doing anything wrong
Check your CCcam.cfg. Open it in notepad, make sure all details are correct.
have you named the config file exactly like this CCcam.cfg
Hi,
I've just reflashed the box again and copied over the cfg file and start cccam and all works fine now. How bizzare it didnt the first time.
Thanks all for your prompt replies :)
Hi,
I'm back to square one after trying few images. I went back to vix and now CCcam wont work again.
The cfg are in place and cam is running but just wont work. It works fine on my dm800.
What can I do to look deeper?
thanks
nope. ive never needed to port forward. my dm800 has no portfowarding set up either and works fine on there.
have you port forwarded?
Hi,
I'm back to square one after trying few images. I went back to vix and now CCcam wont work again.
The cfg are in place and cam is running but just wont work. It works fine on my dm800.
What can I do to look deeper?
thanks
does you config include the clock speed the for card the Vuplus boxes need it to run properly
silverfox0786
22-12-10, 01:51
have a read of this thread
http://www.vuplus-support.co.uk/showthread.php?2758-sly-card-in-vu-duo
put it this way, i've put my cccam.cfg into /etc and it works fine as have many others. so then there are two questions
1/ are you trying to connect to an illegal payserver
2/ have you never set up an internal share before
all answers seem to indicate that you are looking for illegal knowledge that you will not find in this forum
does you config include the clock speed the for card the Vuplus boxes need it to run properly
thats not needed and you canT overclock in VU+
Try setting your config rights/permissions to 755.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.