ABM not updating

[romdut]

For some reason ABM isn't updating after a recent flash, i have tried the manual scan for 11778 H 27500 for the data channels and the TP isn't showing up at all (screen shot attached

I have also checked my list of providers and edit those to sky ire and freesat only (not sure if i only need the one and or both but when i start a scan the tuner times out and i end up with nothing pic 11&12.

I have a lock on the tuner in sat finder pic 14 but in pic 13 i have keyed the TP in manually and i get nothing

Does anyone have any ideas? Im hoping to sit down and watch the F1 soon

Pic's 11 - 14 in next thread

[romdut]

For some reason ABM isn't updating after a recent flash, i have tried the manual scan for 11778 H 27500 for the data channels and the TP isn't showing up at all (screen shot attached

I have also checked my list of providers and edit those to sky ire and freesat only (not sure if i only need the one and or both but when i start a scan the tuner times out and i end up with nothing pic 11&12.

I have a lock on the tuner in sat finder pic 14 but in pic 13 i have keyed the TP in manually and i get nothing

Does anyone have any ideas? Im hoping to sit down and watch the F1 soon

Pic's 11 - 14 in next thread

[abu baniaz]

That transponder does not show in the pre-defined list. You have to manually type it. It is Vertical, not Horizontal. You should check all tuners for a lock on that TP.

Which receiver?
How many tuners?
How many tuners have cables from dish?
What is each tuner configured as?
Navigate to /etc/enigma2/. Look for a file called "settings" Paste the lines that start with the following lines here please.


config.Nims.1.
config.Nims.1.
config.Nims.1.
config.Nims.1.
config.Nims.1.
config.Nims.1.
config.Nims.1.
config.Nims.0.
config.Nims.0.
config.Nims.0.
config.Nims.0.

[Huevos]

Use the settings Abu posted and test on the last tuner. So for example if your box is a twin tuner test tuner B.

[abu baniaz]

I have just looked at your other posts. There is an issue with your setup. If you answer the questions asked, a solution will be reached easily.

[romdut]

That transponder does not show in the pre-defined list. You have to manually type it. It is Vertical, not Horizontal. You should check all tuners for a lock on that TP.

Which receiver? Solo 2
How many tuners? 1
How many tuners have cables from dish? 1
What is each tuner configured as? usuals/motorised
Navigate to /etc/enigma2/. Look for a file called "settings" Paste the lines that start with the following lines here please.


config.Nims.1.
config.Nims.1.
config.Nims.1.
config.Nims.1.
config.Nims.1.
config.Nims.1.
config.Nims.1.
config.Nims.0.
config.Nims.0.
config.Nims.0.
config.Nims.0.
- Done

I am showing 9 channels now on that TP - is this right?
I have just looked for this in the manual scan and 9 came up also

[abu baniaz]

Solo 2 has two tuners.

Which tuner have you plugged the cable into?

The tuner with no cable, what have you set it as?

[romdut]

Solo 2 has two tuners.

Which tuner have you plugged the cable into?

The tuner with no cable, what have you set it as?

I am using tuner a - b is not configured

[Huevos]

If you only have one feed you should configure tuner B and have tuner A set to "not configured".

[abu baniaz]

Post the contents of your settings file.

[romdut]

config.Nims.1.configMode=nothing
config.Nims.1.longitude=1.141
config.Nims.1.diseqcMode=positioner
config.Nims.1.latitude=54.345
config.Nims.1.longitudeOrientation=west
config.Nims.0.userSatellitesList=[30, 31, 48, 49, 70, 90, 100, 101, 130, 160, 170, 171, 192, 201, 216, 235, 255, 260, 261, 282, 305, 306, 315, 330, 360, 380, 381, 390, 401, 420, 450, 460, 461, 475, 480, 491, 505, 506, 525, 530, 531, 550, 560, 570, 571, 600, 601, 620, 621, 642, 643, 650, 660, 661, 685, 686, 705, 722, 740, 741, 750, 751, 765, 766, 785, 786, 801, 830, 831, 851, 865, 876, 880, 881, 900, 901, 915, 916, 922, 935, 936, 950, 965, 966, 1005, 1006, 1030, 1031, 1055, 1056, 1082, 1083, 1106, 1130, 1131, 1156, 1160, 1195, 1222, 1223, 1240, 1251, 1280, 1281, 1320, 1321, 1340, 1341, 1380, 1381, 1400, 1401, 1440, 1520, 1540, 1541, 1560, 1590, 1591, 1600, 1620, 1660, 1661, 1691, 1720, 1721, 1800, 1801, 1829, 2209, 2229, 2249, 2269, 2289, 2310, 2329, 2330, 2349, 2350, 2369, 2370, 2389, 2390, 2409, 2410, 2431, 2432, 2451, 2469, 2470, 2488, 2489, 2500, 2526, 2549, 2550, 2569, 2570, 2589, 2590, 2607, 2608, 2629, 2630, 2649, 2650, 2689, 2690, 2710, 2729, 2730, 2750, 2759, 2769, 2780, 2819, 2820, 2830, 2849, 2850, 2873, 2880, 2899, 2900, 2930, 2949, 2950, 2970, 2985, 2989, 2990, 3019, 3020, 3044, 3045, 3069, 3070, 3099, 3100, 3124, 3149, 3150, 3168, 3169, 3194, 3195, 3224, 3225, 3254, 3255, 3284, 3285, 3300, 3324, 3325, 3354, 3355, 3379, 3380, 3399, 3400, 3419, 3420, 3450, 3459, 3475, 3489, 3490, 3520, 3530, 3549, 3550, 3560, 3591, 3592]
config.Nims.0.diseqcA=282
config.Nims.0.diseqcB=3601
config.Nims.0.diseqcC=3601
config.Nims.0.diseqcD=3601
config.Nims.0.longitude=1.141
config.Nims.0.diseqcMode=positioner
config.Nims.0.simpleSingleSendDiSEqC=true
config.Nims.0.latitude=54.345
config.Nims.0.turningspeedV=2.3
config.Nims.0.advanced.sats=282
config.Nims.0.advanced.sat.282.lnb=1
config.Nims.0.advanced.lnb.1.latitude=54.345
config.Nims.0.advanced.lnb.1.diseqcMode=1_2
config.Nims.0.advanced.lnb.1.powerMeasurement=fals e
config.Nims.0.advanced.lnb.1.longitude=1.141
config.Nims.0.advanced.lnb.1.longitudeOrientation= west
config.Nims.0.longitudeOrientation=west



Is this right in screen shot?

[romdut]

something has worked as the dead channels are now off/gone
All working here
Many thanks

[abu baniaz]

You should find that your cross epg issue should be resolved now.

Just to recap:
If you have a twin tuner receiver, make sure that your config mathces what satllite cabling you have connected.
A twin tuner can use the internal software loopthrough even if there is only one cable.
If you have a Solo 2/TM Nano 2 Super/3T combo, you can loop from B to A. Not A to B. I.e you must connect cable to tuner B.

In my opinion, best not to use the automatic option when setting the tuner.