View Full Version : tuner problem
both tuners seem to work independently, but when tuner A is recording tuner B goes blank, tuner config is set at both tuners on single sat, is this a software or hardware problem, anyone got any ideas
Does Tuner B have a direct feed from LNB?
yes both tuners feed seperately
how have you got your Recordings set in Recording Settings I have mine set to (preferred tuner for recording) auto that way both tuners are available
36769
Swap the feed from Tuner A and connect it to Tuner B.
Now run a Manual single satellite scan.
Menu > Setup > Service Searching > Manual Scan > Set tuner to Tuner B and set type of scan to 'Single Satellite'. You should find 960'ish channels. Test that and report back.
Swap the feed from Tuner A and connect it to Tuner B.
Now run a Manual single satellite scan.
Menu > Setup > Service Searching > Manual Scan > Set tuner to Tuner B and set type of scan to 'Single Satellite'. You should find 960'ish channels. Test that and report back.
hi
did scan on tuner A found 970 channels exactly
did scan on tuner B found 0 channels
turned tuner A off it now found 970 channels
I am aware how these receivers work I have had Dreambox 8000 for over 4yrs, its looking more and more a hardware fault
hi
did scan on tuner A found 970 channels exactly
did scan on tuner B found 0 channels
turned tuner A off it now found 970 channels
I am aware how these receivers work I have had Dreambox 8000 for over 4yrs, its looking more and more a hardware fault
So with Tuner A disabled Tuner B found 970 channels?
Not the LX3 then.
Tuner B working fine you disabled A, I'd look at LNB/Feeds/F connectors/Coax etc....
If tuners where faulty they'd find zero channels full stop.
for testing purposes I am using same cable
how have you got your Recordings set in Recording Settings I have mine set to (preferred tuner for recording) auto that way both tuners are available
36769
my settings are the same
for testing purposes I am using same cable
so that will mean that you are also using the same LNB outlet so you should get the same result --Try the other lead and see what you get
if both tuners are selected tuner B does not work, if tuner A is turned off tuner B works
how many cables do you have connected to the LX3
if both tuners are selected tuner B does not work, if tuner A is turned off tuner B works
Test the receiver connected to a different dish / LNB.
Also check your coax/f connectors.
Do you have both tuners set to simple/single/ 28.2E or is one of them set as loop through
both tuners set to simple/single 28.2E. has said before tuner B will only work if tuner A is switched off, is it worth flashing to build 28 i am using 26
it's worth a try mate flash to 28 but try it without settings restore just to see if you can get the tuners set up properly as you can always restore your settings later
just a thought did you do a fresh install of 26 because restoring from Apollo 24 can give a lot of problems :)
I only got receiver on Thursday, it came with 26 on but would not let me access ftp and telnet so I reflashed and got them to work
Ok I understand now well I think it's worth doing a Fresh Flash to Apollo 28 but without settings restore then you can see how every thing is getting set up just to make sure
I had enough for today I will start again tomorrow, thanks everyone for the input
no problem mate I am ready for a Pint myself :beer_toast:
Dont waste your time flashing. Connect it to another dish / lnb as I've suggested. I've seen Sky dish LNB's cause issues like this when they start going wrong.
Rob van der Does
02-09-14, 06:25
The build in satfinder should also help. See if High/Low/Hor/Vert show fine on both tuners.
hi
took LX3 to a friends who as sky hd tried on his dish same results,reflashed to build 28, both tuners show up in satfinder, signal is in the eighties snr and in the ninties agc
Tune to BBC One HD > Press Record, now zap to ITV HD, do you see ITV HD?
how have you got your Recordings set in Recording Settings I have mine set to (preferred tuner for recording) auto that way both tuners are available
36769
I flashed recently 030 and noticed if I record, other tuner goes blank And can only view certain channels.
Did what nsw9154 suggested and it seemed to sort the issue out.
Still have same problem
What exactly are each of your tuner settings?
What exactly is your satellite dish setup and how is it wired/connected?
What exactly are each of your tuner settings?
What exactly is your satellite dish setup and how is it wired/connected?
Simple, single, 28.2.
Fixed 4 lnb with two cables in back of box
Sorted it. seems to work on 2.3.0 soft am and not on other soft cams, will keep eye on it see but seems to sort out the issues
Hi John, I too had exactly the same problem with tuner B.
I run a Solo2 with Open atv 4.2, and CCamm 2.2.1, so I followed your advice and changed to version 2.3 and all seems to be working fine now.
So thanks to you John, and to all who contributed to this thread
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.