View Full Version : [GiGaBlue QUAD] Boblight, how to identify the usb output?
Hello everyone.
I am trying to run the plugin Boblight.
I have a adalight, and it works because I got the PC working.
the problem I have is that the set, I have to tell the USB output. Inside the folder / dev /.
I've tried: usbdev, ttyACM0 ...
Rob van der Does
21-01-14, 14:18
I always struggle with the same issue (for AtmoLight). But it always seems to be /dev/ttyUSB0
Not sure if the same applies to Adalight.
Hi,
perhaps you find something with lsusb
ciao
yes, I've tried /dev/ttyUSB0 .but does not work.
if I search in /dev/, I do not find ttyUSB. think that's why it does not.
Rob van der Does
21-01-14, 14:36
Hmmm, gives me
root@Ultimo:~# lsusb
Bus 001 Device 001: ID 1d6b:0002
Bus 002 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0001
Bus 004 Device 001: ID 1d6b:0001
Bus 001 Device 002: ID 0718:061a
Bus 003 Device 002: ID 0403:6001
while the setting in BoB-Light is /dev/ttyUSB0 and works fine :confused:
Hmmm, gives me
root@Ultimo:~# lsusb
Bus 001 Device 001: ID 1d6b:0002
Bus 002 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0001
Bus 004 Device 001: ID 1d6b:0001
Bus 001 Device 002: ID 0718:061a
Bus 003 Device 002: ID 0403:6001
while the setting in BoB-Light is /dev/ttyUSB0 and works fine :confused:
hi, thanks for answering. you have it so? have you tried it?, I am surprised me a lot that does not work when the PC runs a clone of the vu + solo too. In vu+ solo clone, I had to find the correct file in the folder: / dev /, " /dev/ttyACM0"
I am surprised me a lot that does not work when the PC runs a clone of the vu + solo too. In vu+ solo clone, I had to find the correct file in the folder: / dev /, " /dev/ttyACM0"
And there ends your support here, please re-read the site rules.
I'm sorry, I understand the rule of NO clones. But I have NO problem with that deco. I have a Gigablue QUAD, original. simply to a reference. not request support for deco clone.
anyone have a working boblight with Openvix? I can not get to the problem.
Rob van der Does
30-01-14, 13:29
anyone have a working boblight with Openvix?
Yes .
Yes .
and you use the route: /dev/ttyUSB0 ?
gigablue quad ? you can tell me exactly which USB port you have connected?
Rob van der Does
30-01-14, 14:22
/dev/ttyUSB0 (bottom upper port at back) for Atmolight on Ultimo & DUO2
/dev/ttyUSB0 (bottom upper port at back) for Atmolight on Ultimo & DUO2
ok, thank you very much for the info. But I do not operate that route, I will try to contact boblight developer.
And I will continue looking for someone who has working in Gigablue quad.
Ok, problem solved.
With the latest version: 0.8r5
And the route: / dev/ttyACM0
working perfectly, ardulitgh with 120 leds.
Rob van der Does
30-01-14, 16:18
Good to hear that: enjoy your lightnings!
How did you find out about '/dev/ttyACM0'?
I found a video on youtube, a GG quad with boblight working.
This video is from a German store, send them a mail. and they have answered me.
I had already tried that route. but not with the latest version, which is a few days ago.
"Asking, one gets to Rome" :D
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.