Anysee E30C tuner

[Peterj]

Hi,

Does anyone know why the Anysee E30C is not recognized as a (USB) tuner?
Drivers are part of the kernel.

root@vuduo2:~# opkg list 'kernel-module-dvb-usb-any*'
kernel-module-dvb-usb-anysee - 3.3.8-r0.10 - linux-vuplus version 3.3.8-r0.10
dvb-usb-anysee kernel module; Driver Anysee E30 DVB-C & DVB-T USB2.0

It's the 1c73:861f

root@vuduo2:~# lsusb
Bus 001 Device 001: ID 1d6b:0002
Bus 002 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0002
Bus 004 Device 001: ID 1d6b:0002
Bus 005 Device 001: ID 1d6b:0001
Bus 006 Device 001: ID 1d6b:0001
Bus 007 Device 001: ID 1d6b:0001
Bus 008 Device 001: ID 1d6b:0001
Bus 004 Device 002: ID 148f:5372
Bus 007 Device 003: ID 1c73:861f

I am trying to use it as a third DVB-C tuner.

[andyblac]

Hi,

Does anyone know why the Anysee E30C is not recognized as a (USB) tuner?
Drivers are part of the kernel.

root@vuduo2:~# opkg list 'kernel-module-dvb-usb-any*'
kernel-module-dvb-usb-anysee - 3.3.8-r0.10 - linux-vuplus version 3.3.8-r0.10
dvb-usb-anysee kernel module; Driver Anysee E30 DVB-C & DVB-T USB2.0

It's the 1c73:861f

root@vuduo2:~# lsusb
Bus 001 Device 001: ID 1d6b:0002
Bus 002 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0002
Bus 004 Device 001: ID 1d6b:0002
Bus 005 Device 001: ID 1d6b:0001
Bus 006 Device 001: ID 1d6b:0001
Bus 007 Device 001: ID 1d6b:0001
Bus 008 Device 001: ID 1d6b:0001
Bus 004 Device 002: ID 148f:5372
Bus 007 Device 003: ID 1c73:861f

I am trying to use it as a third DVB-C tuner.

have you installed them ?

[Peterj]

No, default image.

Sent from my GT-N7000 using Tapatalk

[andyblac]

No, default image.

Sent from my GT-N7000 using Tapatalk

then you need to install the kernel modules.

[Peterj]

Ok. How to do this?

Sent from my GT-N7000 using Tapatalk

[Peterj]

I tried:

root@vuduo2:~# modprobe dvb_usb_anysee adapter_nr=2 delsys=0
FATAL: Module dvb_usb_anysee not found.

[andyblac]

I tried:

root@vuduo2:~# modprobe dvb_usb_anysee adapter_nr=2 delsys=0
FATAL: Module dvb_usb_anysee not found.


you install to INSTALL it.


opkg install kernel-module-dvb-usb-anysee

then reboot.

[Peterj]

sorry, I am new to this. I am not a Linux man.
I did the install.
However no extra tuner available in the menu.

root@vuduo2:~# dmesg | grep usb
__clk_enable: usb [1]
bcm40nm_pm_usb_enable 00
usb 3-1: new high-speed USB device number 2 using ehci-brcm
usbcore: registered new interface driver usb-storage
usbcore: registered new interface driver btusb
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
usb 3-1: device descriptor read/all, error -71
usb 4-1: new high-speed USB device number 2 using ehci-brcm
usb 3-1: new high-speed USB device number 4 using ehci-brcm
usb 3-1: config 1 interface 0 altsetting 0 bulk endpoint 0x1 has invalid maxpacket 64
usb 3-1: config 1 interface 0 altsetting 0 bulk endpoint 0x81 has invalid maxpacket 64
usb 3-1: config 1 interface 0 altsetting 1 bulk endpoint 0x1 has invalid maxpacket 64
usb 3-1: config 1 interface 0 altsetting 1 bulk endpoint 0x81 has invalid maxpacket 64
dvb-usb: found a 'Anysee DVB USB2.0' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
dvb-usb: no frontend was attached by 'Anysee DVB USB2.0'
dvb-usb: Anysee DVB USB2.0 successfully initialized and connected.
usbcore: registered new interface driver dvb_usb_anysee
rtusb init rt2870 --->
usbcore: registered new interface driver rt2870
rtusb init rt2870 --->
usbcore: registered new interface driver rt2800usb



root@vuduo2:~# lsmod
Module Size Used by
rt2800usb 13088 0
rt2800lib 44076 1 rt2800usb
rt2x00usb 10188 1 rt2800usb
rt2x00lib 38800 3 rt2800usb,rt2800lib,rt2x00usb
mac80211 228087 3 rt2800lib,rt2x00usb,rt2x00lib
rt5572sta 898036 0
dvb_usb_anysee 10494 0
mt352 5413 1 dvb_usb_anysee
stv6110 4728 1 dvb_usb_anysee
dvb_pll 8292 1 dvb_usb_anysee
cx24116 14010 1 dvb_usb_anysee
tda10023 6199 1 dvb_usb_anysee
tda18212 2846 1 dvb_usb_anysee
cxd2820r 20329 1 dvb_usb_anysee
isl6423 2168 1 dvb_usb_anysee
zl10353 6509 1 dvb_usb_anysee
stv0900 60851 1 dvb_usb_anysee
ipv6 339310 16
fpga_directc 57649 0
brcmfb 1238 3
dvb_bcm7424 13491457 33 fpga_directc,brcmfb
procmk 1445 2 fpga_directc,dvb_bcm7424

[Peterj]

I figured out that the issue was
dvb-usb: no frontend was attached by 'Anysee DVB USB2.0'.
Searched a lot on the net, but found no answer.
I was thinking it has something to do with USB port, after reading somewhere a remark about downgrading to 1.1 USB. I also had 1 time
dvb-usb: This USB2.0 device cannot be run on a USB1.1 port. (it lacks a hardware PID filter)
dvb-usb: Anysee DVB USB2.0 error while loading driver (-19).
After using a USB hub with separate 5V adaptor, suddenly the Anysee was connected correctly.

dvb-usb: found a 'Anysee DVB USB2.0' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (Anysee DVB USB2.0)
anysee: firmware version:1.2 hardware id:15
DVB: registering adapter 1 frontend 0 (Philips TDA10023 DVB-C)...
DVB: registering adapter 1 frontend 1 (Zarlink ZL10353 DVB-T)...
dvb-usb: Anysee DVB USB2.0 successfully initialized and connected.

After a reboot it was goes gone again.:(

Getting it work, this is how to handle:
disconnect the USB hub.
Reboot the Duo.
connect the USB hub with the Anysee connected to it.
restart enigma2.

With any luck I will get the extra tuner (DVB-C is default for the Anysee).
Also configurable in the menu.

Next step I will try to give the Anysee his own 5V supply.
Will be continued.

[andyblac]

make sure you are using the bottom port at back, i have had issues with DVB tuners on any other port.

[Peterj]

In this case all 3 USB ports act the same.:(

[Peterj]

Separate 5V supply does not help either.

It should be working, it can be working, but is not very user friendly this way.
USB bus driver issue?
Hopefully VUplus is reading this board.

thx andyblac.:thumbsup:

[Peterj]

Luckily it is working very well on my brand new ET6500, after installing the driver as Andyblac suggested.
:)

[Peterj]

Same problem with the Solo SE. :(