ViX Backup manager not working !!.

[nowbody]

i tryed several times to flash a backuped image. but it always fails. I used "confi" - ViX for backup image. after that i copy the "backup" to a usb-drive. Flashing works, but after flashing the solo2 hangs by "Starting".
now i used "enigma2-plugin-extensions-backupsuite_11.8_mips32el" and this works fine.

[nowbody]

backuosuite 12.0 works fine too...
addind to onlineupdate would be nice... :)

[Larry-G]

backuosuite 12.0 works fine too...
addind to onlineupdate would be nice... :)

Backupsuite is a bit pointless in the ViX image as there is a custom made and highly customized set of backup and image backup managers built rite into the image by default, loading a third party backup manager can cause problems with these built in plugins.

[nowbody]

i have not used a third party backup before. tha problem was only with buildin image backup.

[nowbody]

Kernel backup size:
buildin backup: 7.168KB <- works not
pedro´s backupsuite :7.040KB <- works

[Larry-G]

i have not used a third party backup before. tha problem was only with buildin image backup.

without debug logs we really cant help as we would just be guessing as to your problem.

[Larry-G]

I have moved your posts out of the solo2 image discussion thread as that is not the correct place to be seeking help and your posts are likely to get lost in the rabble.

[nowbody]

flashing backup image is not working.
i want to flash a backupimage (build with vix build-in backuptool). after restart the solo2 hangs by "starting".
i tried several times, but nothing changes.

after this fail i tested pedro´s backupsuit and this works without a problem.

i had have a look at kernel filesizes:
buildin backup: 7.168KB <- works not
pedro´s backupsuite :7.040KB <- works

there is no error when backing up the image with vix-tool. also there is no logfile on the hdd.

[nowbody]

at same time i made a new one...
can you merge it?

[Larry-G]

at same time i made a new one...
can you merge it?

yes thats fine i have merged both threads together.

[nowbody]

i dont know if this is a "vu" problem in general. possibly this is only a solo2 problem...

[nowbody]

serial log:

73460012ux] 1. V

BCM7356B2 CFE Build Date: Fri Nov 23 11:23:42 2012 Vuplus team
[LCD4linux] creating LCD-Picture
[Boblight:Write] Se
Copyright (C) Broadcom Corporation.0)s: ncq sntf stag clo slum part
[L

CPU speed: 1305MHzOKblight:Write] Set opti
Total memory(0): 1024MBrise downloadstart: htt
DDR Freq: 800 MHzn/51.3829994/11.6ta
[Bob
DDR Mode: DDR3n mode dynamic (127.0
DEV TECH: 2048MBIT
000004/1/4/2/1
DDR Width: 32 RunTime: 0.404 (Pi
Boot Device: NAND0.378 (0.378/0.000))o
Total flash: 256MBort 0x180 irq 41

Initializing USB.
[LCD4linu
USB: Locating Class 09 Vendor 0000 Product 0000: USB Root Hubux] (7, 47) (20, 57)
[eDVBLocalTi
USB: Locating Class 09 Vendor 0000 Product 0000: USB Root Hub/WebInterface failed to load: No module named pluginown (SSt

USB: Locating Class 09 Vendor 0000 Product 0000: USB Root HubPlugin probably removed, but not cleanly in /uon
ehci-brcm ehci-brcm.0: new USB bu
[LCD4l
USB: Locating Class FF Vendor 0403 Product 6001: Driver not found.
[LCD4linux] Registering FritzCall...-8: WDC WD10TPVT-00U4RT1
USB: New device connected to bus 3 hub 1 port 1
[LCD4linux]
USB: Resetting device on bus 3 hub 1 port 1 31/32)
[LCD4linux] NcidClient not register
USB: Locating Class 08 Vendor 08EC Product 0008: Mass-Storage Devicede]
ehci-brcm ehc
[AtmoLight] set language to [de]
USBMASS: Unit 0 connected
[AtmoLight] fallba
waiting for usb...doneon for Layout WDC
checking usb
--> setting satu
Checking usbdisk0:/vuplus/solo2/kernel_cfe_auto.bin......YEStting hue to: 00008000
sd 1:0:0:0: [sda] Write
--> setti
Checking usbdisk0:/vuplus/solo2/reboot.update......YES
--> setting block_noise_reduction to: 00000000
waiting for update keyFUA

ACK :
Reading usbdisk0:/vuplus/solo2/cfe_cfe_auto.bin: Skipping...: File not found
ehci
--> setting splitmode to: offrted, EHCI 1.00
-
Reading usbdisk0:/vuplus/solo2/initrd_cfe_auto.bin: Skipping...: File not founduto_flesh to: 00000000ort detected
--> setting green_boos

Reading usbdisk0:/vuplus/solo2/splash_cfe_auto.bin: Skipping...: File not found0000 new USB bus registered, assigned b
--> setting dynamic_contrast to: 0000000

Reading usbdisk0:/vuplus/solo2/kernel_cfe_auto.bin: Done. 7340032 bytes reado)490300
--> applying pep valuescm ehci-brcm.

Programming...teControlCode>
done. 7340032 bytes written 2
hub 3-
Checking usbdisk0:/vuplus/solo2/root_cfe_auto.bin......YES 1 port detected
remove DVI-PC because of not existing
Loader:elf Filesys:raw Dev:flash0.initrd Fi
getModeList for por
Using 1024 MB + 0 MB RAM (from CFE)DVI mode: 1080i rate: multi
bootconsole [early0] enabled
ohc
-> setting aspect, po
CPU revision is: 00025a11 (Broadcom BMIPS5000)o
hub 5-0:1.0: USB hub
FPU revision is: 00130001XMLTVImport] autostart (0
Determined physical RAM map:
ohci-brcm ohci-brcm
bmem: adding 256 MB RESERVED region at 512 MB (0x10000000@0x20000000)ci-brcm.2: Broadcom STB OHCI
[SoftcamManager] AutoStart Enable
Initrd not found or empty - disabling initrdnment] activating ci configs:
Zone PFN ranges:
[CI_Activ
Normal 0x00000000 -> 0x00050000: irq 76, io me
[CI_Activate_Config
Movable zone start PFN for each node
hub 7-0:1.0: USB hub found
[
Early memory PFN rangeserror parsing xml...ect
0: 0x00000000 -> 0x00010000hci-brcm o
starting hotplug han
0: 0x00020000 -> 0x00050000mer] Record RecordTimerEntry(na
PERCPU: Embedded 7 pages/cpu @81a09000 s5760 r8192 d14720 u32768


Detected MIPS clock frequency: 1305 MHz (163.135 MHz counter)initialized
usbcore: regist
Console: colour dummy device 80x25, serviceref=1:0:1:2EE3:441:1:C000
Calibrating delay loop... 869.37 BogoMIPS (lpj=434688)e driver
[Timer] Reco
pid_max: default: 32768 minimum: 301egin=Thu Apr 4 17:27:00 2013,
Mount-cache hash table entries: 512F driver helper
SMP: Booting CPU1...EE3:441:1:C00000:0:0
CPU revision is: 00025a11 (Broadcom BMIPS5000)
[Timer] Record RecordT
FPU revision is: 00130001ählt, begin=Thu Apr 4 1
Primary instruction cache 32kB, physically tfound.


NET: Registered protocol family 16:2EE3:441:1:C00000:0:0:0:, justpla
USB0: power enable is active high; overcurrent is active low
EBI C
[Timer] Record RecordTimerEntry(name=Unter
USB1: power enable is active high; overcurrent is active low: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bi
serv
bio: create slab <bio-0> at 0:0:0:0:, justplay=0)
SCSI subsystem initialized brcmnand.0: 256Mi
[Timer]
usbcore: registered new interface driver usbfs begin=Fri Apr 5 19:02:00
usbcore: registered new interface driver hub
Bad blo
2013, serviceref=1:0:1:2EE3
usbcore: registered new device driver usb
Bad block table fo
Switching to clocksource
TCP reno registeredRecord RecordTimerE
UDP hash table entries: 512 (order: 2, 16384 bytes),
0x000001f00000-0x000010000000 : "r
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)B:1:C00000:0:0:0:, justplay=0)redundant)"
NET: Registered protocol family 1mer] Record RecordTimerEntry(name
RPC: Registered named UNIX socket transport module.x000000900000-0x000000a00000 : "mac"
UBI: sm
squashfs: version 4.0 (2009/01/31) Phillip Lougher:0:, justplay=0)
UBI: VID header offset:
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.rEntry(name=Gute Zeiten, schlechte Zeiten, begin=Mon
fuse init (API version 7.18)
usb 6-1: new fu
msgmni has been set to 1105 8 19:37:00 2013, servicer
io scheduler noop registered0:0:, justplay=0)
UBI: max
io scheduler cfq registered (default)
[Timer] Rec
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled:57:00 2013, "rootfs"
console [ttyS0] enabled, bootconsole disabled 65) is a 16550AFB:1:C00000:0:0:0:, justplay=0)
UBI: number of good PEBs:
console [ttyS0] enabled, bootconsole
Config GPHY through MDIOplay=0)
UBI: total nu
No PHY detected, not registering interface:1r] Record RecordTimerEntry(name=Sportschau,
bcmgenet: probe of bcmgenet.1 failed with error -5
UBI: max/mean e
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet drivernce number: 389667660
[Timer] Record
usbcore: registered new interface driver pegasus7 18:27:00 2013,

UBI
usbcore: registered new interface driver asixy

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver7:00 2013, serviceref=1:0:1:2EE3:441:1:C00000:0:0:0:, just
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
V
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1 28 19:02:00
devtmpfs: mounted
ehci-brcm ehci-brcm.0: irq 69, io mem 0x104803002EE3:441:1:C00000:0:0:0:, justplay=0)T: version
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00

Disabling lock debugging due to kernel tai
, jus
ehci-brcm ehci-brcm.1: irq 70, io mem 0x10480500ntry(name=Meine Frau, unsere Kinder und ich, beg
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
Hotplug
t Mar 30 00:4
hub 2-0:1.0: USB hub found9:132F:3EF:1:C00000:0:0:0:
hub 2-0:1.0: 1 port detected
Hotplug - connect
ehci-brcm ehci-brcm.2: Broadcom STB EHCIr] Record RecordTimerEntry(name=Sportsch
ehci-brcm ehci-brcm.2: new USB bus registered, assigned bus number 3
DVB
serviceref=1:0:19:28
ehci-brcm ehci-brcm.2: irq 74, io mem 0x10490300
DVB: regi
[Time
ehci-brcm ehci-brcm.2: USB 0.0 started
hub 4-0:1.0: USB hub foundt V3.0r2 (/tmp/)...

hub 4-0:1.0: 1 port detected[LCD4linux] create /tmp/lcd4
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) DriverbIf-Init...
363, 43560, mag
[LCD4linux] no We
ohci-brcm ohci-brcm.0: Broadcom STB OHCIlinux] create Link
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 5ces
[LCD4linux] enable FritzCallUserAction-Timer
ohci-brcm ohci-brcm.0: irq 71, iux] get DPF regist
N
hub 6-0:1.0: USB hub foundily 10
[MultiQuickBut
hub 6-0:1.0: 1 port detectedtered new interface dri
----
ohci-brcm ohci-brcm.2: Broadcom STB OHCI--------------------- Serial support reg
ohci-brcm ohci-brcm.2: new USB bus registered, assigned bus number 7art Enabled new interface driver usbserial_
[ImageManager] Backup Sc
ohci-brcm ohci-brcm.2: irq 76, io mem 0x10490400EST)SB Serial Driver core
hub 7-0:1.0: USB hub foundrt reg
[BackupManager] Aut
hub 7-0:1.0: 1 port detected

ohci-brcm ohci-brcm.3: Broadcom
Initializing USB Mass Storage driver...ttyUSB0
port changed
usbcore: registered new interface driver usb-storage new interface d
getModeList for port DVI
USB Mass Storage support registered.dard')0:USB FTDI Serial Converters

mousedev: PS/2 mouse device common for all mice'576i', '480i', ('1080i', 'Standttings...
sdhci: Secure Digital Host Controller Interface driverces... ADD
ard')]ETDEV_
[XMLTVImport] autostart (0) oc
sdhci: Copyright(c) Pierre Ossman
TCP cubic registeredndInfoBar'>s = 0
NET: Registered protocol family 17t epg_description in <class 'Scree
PM: CP0 COUNT/COMPARE frequency does not depend on divisor
Starting Dropbear SSH server
ics.SecondInfoBar'>
EBI CS0: setting up NAND flash (primary)g element key_green in <class 'Screens.I
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-biing syslogd/klog
condInfoBar'>
warning, skin is missing element key
t)d
brcmnand brcmnand.0: 256MiB total, 128KiB blocks, 2KiB
...done.
Distro:

nand_read_bbt: bad block at 0x000005f60000are/enigma2/skin_default/icons/dvb-c.png
nand_read_bbt: bad block at 0x000006b80000- double buffering avai
[ePNG] couldn't op
nand_read_bbt: bad block at 0x0000077c0000b-t.png[LCD]: unknown cmd 0x1015
nand_read_bbt: bad block at 0x00000a9c0000uldn't open /usr/share/enigma2/skin_defaul
nand_read_bbt: bad block at 0x00000ff20000
+ (9) gLCDDC
Creating 3 MTD partitions on "brcmnand.0":ySummary buffer 0x7d6ab0 8448 bytes, strid
0x000001f00000-0x000010000000 : "rootfs"tusicon in <class 'Scree32 x 64 x 8 (str
Moscsi0 : usb-storage 4-1:1.0
+ (20) DVB-CI U
warning, s
unting virtual filesystemsred in <class 'Screens.Inf
Starting mdevfmod0!!!!
* WARNING: THIS STB CONTAINS GPLv3 SOFTWAREer
warning, skin is missi
* GPLv3 programs must be removed in order to enable security.
couldnt open /dev/dbox/fp0 to monitor vcr scart slow blank
* See: http://www.gnu.org/licenses/gpl-faq.html#Tivoization <class 'Screens.InfoBar.InfoBar'>t device[CI]: CI interfac
Configuusb 6-1: new full-speed USB device number 2 using ohci-brcm] Skin RdsInfoDisplayice "dreambox advanced remote c
[LCD4linux] S
ring eth0 interface
Configuring lo intex] Sk
scsi 0:0:0:0: Direct-Access Hama FlashPen 1.04 PQ: 0 ANSI: 0 CCSutSource(1, 1)
[LogManager] found following log's: ['/home/root/logs']

sd 0:0:0:0: Attached scsi generic sg0 type 0+ (35) CA
[LogManager] looking in: /home/roo
checking sda ..
sd 0:0:0:0: [sda] 2007040 512-byte logical blocks: (1.02 GB/980 MiB)ixmapNum(0) failed! defined pixmaps: []
+ (41
sd 0:0:0:0: [sda] Write Protect is offor
+ (41) eServiceFact
allocate
sd 0:0:0:0: [sda] No Caching mode page present
opening frontend 0
+ (41) eServi
(0)tuney
sd 0:0:0:0: [sda] Assuming drive cache: write through
---- opening lame channel db

ce number 2 using ohci-brcmork mounts...
pipes closedu
libscan: scanning eraseblock 1799 -- 100 % complete
pipes closed/Videos
child has terminated LCD-
ubiformat: 1790 eraseblocks have valid erase counter, mean value is 22, data:
new Network M

poll: unhandled POLLERR/
ubiformat: 10 bad eraseblocks found, numbers: 476, 515, 612, 710, 1110, 1793, 17led POLLERR/HUP/NVAL for fd 45(16)nternal link on frontend id 0uild Date: Fri No
96, 1797, 1798, 17992
sec config cleared
ubiformat: flashing eraseblock 759 -- 100 % completeslotid 0, descr BCM735
poll: unhandled POLLERR/HUP/N
ubiformat: formatting eraseblock 1799 -- 100 % complete
child has terminatedorworkaround No, ena
pipes
Rebooting in 9 seconds: unhandled POLLERR/HU
Rebooting in 8 secondsotInfo for dvb fronten
Rebooting in 7 secondshild has terminated(in
Rebooting in 6 seconds closed 32
po
Rebooting in 5 secondsUP/NVAL for fd 54(16)
Rebooting in 4 seconds, enabled Yes, DVB
Rebooting in 3 seco

BCM7356B2 CFE Build Date: Fri Nov 23 11:23:42 2012 Vuplus teamamsserbouquet.ED00.tv 1
[SEC] setVoltage 2values
Copyright (C) Broadcom Corporation.rbouquet.
[SEC] setTone 1


MAC ADDRESS CHECKSUM FAILED. bouquet
[SEC] update curren
MAC ADDRESS MUST BE PROGRAMMED!, using macprog command startTuneTimeout 5000ntries in Bouquet userbouqu
[SEC
CPU speed: 1305MHz
setting fronte
Total memory(0): 1024MB0)fe event: status 0, i
DDR Freq: 800 MHz
DDR Mode: DDR3n
[SEC] sleep 500mset
DEV TECH: 2048MBITterminated
checking u

DDR Width: 3

USB: Locating Class 09 Vendor 0000 Product 0000: USB Root HubSTATE: okfe_auto.bin.
[eDVBLocalTimerHandler] channel 0x74d08
Saving shmoo values...
Checking usbdisk0:
Saved shmoo values....ache] channel 0x74d086

CFE initialized.t.ED00.radio
USB: Device disconnected from bus 0 hub 1 port 1bouquet... /etc/en
ok ... now we start!!urites.r
USB: New device connected to bus 1 hub 1 port 1
have 1 video stream(s) (00a3), and
USB: Resetting device on bus 1 hub 1 port 1

A
USBMASS: Unit 0 connectedg font /usr/share/fon
AUD
waiting for usb...doneold)ot
AUDIO_PLAY - ok
Programming flash...doneice: /dev/dvb/adapter0/v
checking usbont /usr/sha
Found high priority Mass Storage bus = 3, index = 0mux0g 1024 MB + 0 MB RAM (from CFE)
VIDEO_SET
checking front key adding font /usr/
readFrontKey 0 0PES_FILTER(0xa3)
Checking usbdisk0:/vuplus/solo2/ignore.update......NOUX_START - video - okFONT] adding font /usr/s
VIDEO_F
Checking usbdisk0:/vuplus/solo2/force.update......NO
DMX_SET_PES_FILTER(0x69) - ttx
Checking usbdisk0:/vuplus/solo2/reboot.update......YES
setPixmapNum(0) failed! defined pixmaps: []

waiting for update key10000
setPixmapNu
ACK :ailed
readFrontKey 0x0: []ts/lcd.ttf..
ACK :CD)
ACK :
readFrontKey 0x0t exists : /tmp/

**Exception 32: EPC=80577AE0, Cause=00008028, VAddr=77098AD0
RA=8700D024, PRID=00025A11

0 ($00) = 00000000 AT ($01) = A0000000
v0 ($02) = 00040000 v1 ($03) = 00000080
a0 ($04) = 870575C0 a1 ($05) = 00000000
a2 ($06) = 8700D098 a3 ($07) = 43464531
t0 ($08) = 80568AB0 t1 ($09) = 8003FF80
t2 ($10) = FFFFFF80 t3 ($11) = 87083040
t4 ($12) = 00000001 t5 ($13) = 00000001
t6 ($14) = 8700D4F4 t7 ($15) = 87001620
s0 ($16) = 8700D024 s1 ($17) = FFFFC380
s2 ($18) = 00000000 s3 ($19) = 8700E264
s4 ($20) = 87455198 s5 ($21) = FFFFD000
s6 ($22) = 00000000 s7 ($23) = 87034E7C
t8 ($24) = 000006DC t9 ($25) = 8708301C
k0 ($26) = 870856D8 k1 ($27) = 00000000
gp ($28) = 870575C0 sp ($29) = 87454FF8
fp ($30) = 8701554C ra ($31) = 8700D024


*** Waiting for system reset ***

[judge]

What exactly are you trying to do?

[nowbody]

1: backup image (vix backuptool)
2: flash back the backup (usbstick)
3: error when restarting after flashing the backupimage ->"starting" in display...

[judge]

Is it a fresh flash from http://openvix.co.UK you are using?
What build number? Are you installing any plugins before doing the backup? If so, which ones?

[nowbody]

yes ist a fresh one (openvix-3.0.632). Plugins i installed: atmolight, boblight, lcd4linux, MQB, Radioonline, webmedia, webradioFS.

[judge]

does it work for you wothout installing any of those plugins?

[nowbody]

does not work...

[nowbody]

today i flashed again "openvix-3.0.632-vusolo2_usb". i only set sat-config. no plugins, noch channellist. then i made a new backupimage.
the backupimage i tryed to flash back. still the same problem.
serial log:

73460012

BCM7356B2 CFE Build Date: Fri Nov 23 11:23:42 2012 Vuplus team
Copyright (C) Broadcom Corporation.

CPU speed: 1305MHz
Total memory(0): 1024MB
DDR Freq: 800 MHz
DDR Mode: DDR3
DEV TECH: 2048MBIT
DDR Width: 32
Boot Device: NAND
Total flash: 256MB

Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000: USB Root Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Root Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Root Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Root Hub
Saving shmoo values...
Saved shmoo values....

CFE initialized.
USB: New device connected to bus 1 hub 1 port 1
USB: Resetting device on bus 1 hub 1 port 1
USB: Locating Class FF Vendor 0403 Product 6001: Driver not found.
waiting for usb...done
checking usb
No Priority Usb
checking front key
readFrontKey 0 0
Checking usbdisk0:/vuplus/solo2/ignore.update......NO
Checking usbdisk0:/vuplus/solo2/force.update......NO
Checking usbdisk0:/vuplus/solo2/cfe_cfe_
Checking usbdisk0:/vuplus/solo2/root_cfe_auto.bin......NO
....NO
Checking usbdisk0:/vuplus/solo2/splash_cfe_auto.bin......NO
Checking usbdisk0:/vuplus/solo2/kernel_cfe_auto.bin......NO
Starting splash screen.
No valid image found in flash0.splash - disabling splash

Loader:elf Filesys:raw Dev:flash0.kernel File: Options:ubiroot rootflags=sync bm
em=192M@64M bmem=256M@512M
Loading: 0x80001000/7190016 0x806dc600/121776 Entry address is 0x80568ab0
Starting program at 0x80568ab0

**Exception 32: EPC=80577AE0, Cause=00008028, VAddr=73747E6F
RA=8700D024, PRID=00025A11

0 ($00) = 00000000 AT ($01) = A0000000
v0 ($02) = 00040000 v1 ($03) = 00000080
a0 ($04) = 870575C0 a1 ($05) = 00000000
a2 ($06) = 8700D098 a3 ($07) = 43464531
t0 ($08) = 80568AB0 t1 ($09) = 8003FF80
t2 ($10) = FFFFFF80 t3 ($11) = 87081DB0
t4 ($12) = 00000001 t5 ($13) = 00000001
t6 ($14) = 8700D4F4 t7 ($15) = 87001620
s0 ($16) = 8700D024 s1 ($17) = FFFFC380
s2 ($18) = 00000000 s3 ($19) = 8700E264
s4 ($20) = 87455198 s5 ($21) = FFFFD000
s6 ($22) = 00000000 s7 ($23) = 87034E7C
t8 ($24) = 000006DC t9 ($25) = 87081DD4
k0 ($26) = 87084218 k1 ($27) = 00000000
gp ($28) = 870575C0 sp ($29) = 87454FF8
fp ($30) = 8701554C ra ($31) = 8700D024


*** Waiting for system reset ***

[andyblac]

today i flashed again "openvix-3.0.632-vusolo2_usb". i only set sat-config. no plugins, noch channellist. then i made a new backupimage.
the backupimage i tryed to flash back. still the same problem.
serial log:

73460012

BCM7356B2 CFE Build Date: Fri Nov 23 11:23:42 2012 Vuplus team
Copyright (C) Broadcom Corporation.

CPU speed: 1305MHz
Total memory(0): 1024MB
DDR Freq: 800 MHz
DDR Mode: DDR3
DEV TECH: 2048MBIT
DDR Width: 32
Boot Device: NAND
Total flash: 256MB

Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000: USB Root Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Root Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Root Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Root Hub
Saving shmoo values...
Saved shmoo values....

CFE initialized.
USB: New device connected to bus 1 hub 1 port 1
USB: Resetting device on bus 1 hub 1 port 1
USB: Locating Class FF Vendor 0403 Product 6001: Driver not found.
waiting for usb...done
checking usb
No Priority Usb
checking front key
readFrontKey 0 0
Checking usbdisk0:/vuplus/solo2/ignore.update......NO
Checking usbdisk0:/vuplus/solo2/force.update......NO
Checking usbdisk0:/vuplus/solo2/cfe_cfe_
Checking usbdisk0:/vuplus/solo2/root_cfe_auto.bin......NO
....NO
Checking usbdisk0:/vuplus/solo2/splash_cfe_auto.bin......NO
Checking usbdisk0:/vuplus/solo2/kernel_cfe_auto.bin......NO
Starting splash screen.
No valid image found in flash0.splash - disabling splash

Loader:elf Filesys:raw Dev:flash0.kernel File: Options:ubiroot rootflags=sync bm
em=192M@64M bmem=256M@512M
Loading: 0x80001000/7190016 0x806dc600/121776 Entry address is 0x80568ab0
Starting program at 0x80568ab0

**Exception 32: EPC=80577AE0, Cause=00008028, VAddr=73747E6F
RA=8700D024, PRID=00025A11

0 ($00) = 00000000 AT ($01) = A0000000
v0 ($02) = 00040000 v1 ($03) = 00000080
a0 ($04) = 870575C0 a1 ($05) = 00000000
a2 ($06) = 8700D098 a3 ($07) = 43464531
t0 ($08) = 80568AB0 t1 ($09) = 8003FF80
t2 ($10) = FFFFFF80 t3 ($11) = 87081DB0
t4 ($12) = 00000001 t5 ($13) = 00000001
t6 ($14) = 8700D4F4 t7 ($15) = 87001620
s0 ($16) = 8700D024 s1 ($17) = FFFFC380
s2 ($18) = 00000000 s3 ($19) = 8700E264
s4 ($20) = 87455198 s5 ($21) = FFFFD000
s6 ($22) = 00000000 s7 ($23) = 87034E7C
t8 ($24) = 000006DC t9 ($25) = 87081DD4
k0 ($26) = 87084218 k1 ($27) = 00000000
gp ($28) = 870575C0 sp ($29) = 87454FF8
fp ($30) = 8701554C ra ($31) = 8700D024


*** Waiting for system reset ***

please backup for me to check.

[nowbody]

i sent you the downloadlink

[nowbody]

@ andyblac:
did you get the link?

[andyblac]

@ andyblac:
did you get the link?

yes, i'll check today,

[nowbody]

any news? have you checked the image?
is still get different kernel sizes when backing up with backupsuit and vix backup...

[nowbody]

where is the problem? will there be some update or have i made some mistakes?

[judge]

I just made a back-up image using build 647 to test this & it flashed without issue, using a Solo2.
What box are you using?

[Larry-G]

where is the problem? will there be some update or have i made some mistakes?

I have updated a solo2 and a TM Twin to build 647, then made a full image backup on both with the inbuilt image manager. both receivers were then restored with those backups just fine and with no issues at all.

[nowbody]

andyblac have checked the image i have uploaded....
seams that nobody reads this...

[nowbody]

updated to 647 but still same problem with restoring vix backupimage:

73460012

BCM7356B2 CFE Build Date: Fri Nov 23 11:23:42 2012 Vuplus team
Copyright (C) Broadcom Corporation.

CPU speed: 1305MHz
Total memory(0): 1024MB
DDR Freq: 800 MHz
DDR Mode: DDR3
DEV TECH: 2048MBIT
DDR Width: 32
Boot Device: NAND
Total flash: 256MB

Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000: USB Root Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Root Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Root Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Root Hub
Saving shmoo values...
Saved shmoo values....

CFE initialized.
USB: New device connected to bus 1 hub 1 port 1
USB: Resetting device on bus 1 hub 1 port 1
USB: Locating Class FF Vendor 0403 Product 6001: Driver not found.
waiting for usb...done
checking usb
No Priority Usb
checking front key
readFrontKey 0 0
Checking usbdisk0:/vuplus/solo2/ignore.update......NO
Checking usbdisk0:/vuplus/solo2/force.update......NO
Checking usbdisk0:/vuplus/solo2/cfe_cfe_
Checking usbdisk0:/vuplus/solo2/root_cfe_auto.bin......NO
....NO
Checking usbdisk0:/vuplus/solo2/splash_cfe_auto.bin......NO
Checking usbdisk0:/vuplus/solo2/kernel_cfe_auto.bin......NO
Starting splash screen.
No valid image found in flash0.splash - disabling splash

Loader:elf Filesys:raw Dev:flash0.kernel File: Options:ubiroot rootflags=sync bm
em=192M@64M bmem=256M@512M
Loading: 0x80001000/7190016 0x806dc600/121776 Entry address is 0x80568ab0
Starting program at 0x80568ab0

**Exception 32: EPC=80577AE0, Cause=00008028, VAddr=63747E6F
RA=8700D024, PRID=00025A11

0 ($00) = 00000000 AT ($01) = A0000000
v0 ($02) = 00040000 v1 ($03) = 00000080
a0 ($04) = 870575C0 a1 ($05) = 00000000
a2 ($06) = 8700D098 a3 ($07) = 43464531
t0 ($08) = 80568AB0 t1 ($09) = 8003FF80
t2 ($10) = FFFFFF80 t3 ($11) = 87081DB0
t4 ($12) = 00000001 t5 ($13) = 00000001
t6 ($14) = 8700D4F4 t7 ($15) = 87001620
s0 ($16) = 8700D024 s1 ($17) = FFFFC380
s2 ($18) = 00000000 s3 ($19) = 8700E264
s4 ($20) = 87455198 s5 ($21) = FFFFD000
s6 ($22) = 00000000 s7 ($23) = 87034E7C
t8 ($24) = 000006DC t9 ($25) = 87081DD4
k0 ($26) = 87084218 k1 ($27) = 00000000
gp ($28) = 870575C0 sp ($29) = 87454FF8
fp ($30) = 8701554C ra ($31) = 8700D024


*** Waiting for system reset ***

[Larry-G]

andyblac have checked the image i have uploaded....
seams that nobody reads this...

I read what you posted and as i replied. I tested the Image backup feature on two receivers using the latest image and both worked fine, i also tested a settings backup using the backup manager and that worked too.

[nowbody]

attached please look at kernelfilesize. Whats your kernelfilesize with vxi backup?24905

[Larry-G]

i'm at work at the moment so i cant check but when i get in this evening i'll check for you.

[judge]

andyblac have checked the image i have uploaded....
seams that nobody reads this...

you've had atleast 2 people test this without issue, seems like you are the one not reading...
what box, image & build number are you currently using that's failing creating backups?
and what exactly are you trying to do?

[nowbody]

with every buildnumer same problem. look at post #32 there you can see last time 3.0.647...
restoring backuped vix-image is not working on my solo2. you can read it in more than one post.
dl link witch i send andyblac: https://dl.dropbox.com/u/96008826/fail%20vusolo2-3.0.632-20130328_165014.rar

[Larry-G]

with every buildnumer same problem. look at post #32 there you can see last time 3.0.647...
restoring backuped vix-image is not working on my solo2. you can read it in more than one post.
dl link witch i send andyblac: https://dl.dropbox.com/u/96008826/fail%20vusolo2-3.0.632-20130328_165014.rar

as i said I made a backup on my solo2 last night with build 647 and it restored via USB just fine, judge has done the same again without problem. now were not trying to deny you have a problem but we are not able to replicate it here.

[nowbody]

i understand that. with "enigma2-plugin-extensions-backupsuite_12.0_mips32el" i have no problem too. only using vix-backup makes some problems.
why do i get different kernelfilesizes with "enigma2-plugin-extensions-backupsuite_12.0_mips32el" and vix-backup?

[judge]

why are you installing enigma2-plugin-extensions-backupsuite_12.0_mips32el & are you doing the vix-backup with this extension installed?

still no idea why you are having problems with this, Solo2, build 647 backup images working perfectly here.

[Larry-G]

i understand that. with "enigma2-plugin-extensions-backupsuite_12.0_mips32el" i have no problem too. only using vix-backup makes some problems.
why do i get different kernelfilesizes with "enigma2-plugin-extensions-backupsuite_12.0_mips32el" and vix-backup?

There very different pieces of software, one is specifically developed, maintained and updated for the ViX image the other is a "jack of all trades" so to speak. and as i said earlier the backup suite is not fully ViX compatible and thus may cause issues.

[nowbody]

no i wrote before i do not use backupsuite_12.0 before. i installed it later because i need a backup-app.
in the image i posted above there is no backupsuite_12.0 and no other plugin installed, no channellist or something else. nevertheless i get the same error!
have a look at this: https://dl.dropbox.com/u/96008826/fa...328_165014.rar

[Larry-G]

no i wrote before i do not use backupsuite_12.0 before. i installed it later because i need a backup-app.
in the image i posted above there is no backupsuite_12.0 and no other plugin installed, no channellist or something else. nevertheless i get the same error!
have a look at this: https://dl.dropbox.com/u/96008826/fa...328_165014.rar

i'll download that later after work and see if it installs to my solo2, i'll also get you the file size you required from my own backup to compare to yours.

[Larry-G]

EDIT,

that link is giving a 404 error so i cant download any thing.

[nowbody]

@ pheonix: thank you!

[Larry-G]

also something to consider, the last time i tested backup suite it created another backup to the HDD of my receiver and it is known that a solo2 will try to flash any backup it detects even if from a internal HDD. so look on your HDD and check there are none saved there as it may be bypassing your USB stick and loading or trying to load one from the HDD instead.

[nowbody]

i will upload it somewhere else... one moment...

[nowbody]

also something to consider, the last time i tested backup suite it created another backup to the HDD of my receiver and it is known that a solo2 will try to flash any backup it detects even if from a internal HDD. so look on your HDD and check there are none saved there as it may be bypassing your USB stick and loading or trying to load one from the HDD instead.

making backups only with disconnected usb-drive.
for restoring is always use the backup in the solo2´s hdd, fore example: imagebackups\vusolo2-3.0.647-20130407_120139

[Larry-G]

making backups only with disconnected usb-drive.
for restoring is always use the backup in the solo2´s hdd, fore example: imagebackups\vusolo2-3.0.647-20130407_120139

Try removing all those backups from the receiver so that it cant try to load them when your trying to flash from the USB stick. also you say USB drive do you mean USB HDD or a USB stick / pen ??. and have you tried multiple USB sticks to rule out a faulty one ??.

[judge]

making backups only with disconnected usb-drive.
for restoring is always use the backup in the solo2´s hdd, fore example: imagebackups\vusolo2-3.0.647-20130407_120139

and in that back-up folder "vusolo2-3.0.647-20130407_120139" you have a vuplus directory, are you coping that to the root of your USB stick?
also, not much point in uploading a back-up that you know doesn't work.
Try a fresh flash of build 643 (latest available on http://www.world-of-satellite.com/enigma2/openvix/index.php?dir=Vu%2BSolo2/), create a backup & let us know if you are still having the same issue restoring it.

[nowbody]

new link: http://www.share-online.biz/dl/FACCSVKM5J96

[nowbody]

and in that back-up folder "vusolo2-3.0.647-20130407_120139" you have a vuplus directory, are you coping that to the root of your USB stick?
also, not much point in uploading a back-up that you know doesn't work.
Try a fresh flash of build 643 (latest available on http://www.world-of-satellite.com/enigma2/openvix/index.php?dir=Vu%2BSolo2/), create a backup & let us know if you are still having the same issue restoring it.
i can no create i backup thats works. 647 and 632 same problem...

[judge]

Just tried anoter back-up, this time with various networking plugins installed, OnDemand & a couple of others.
The back-up restores with no problems.

Must be something funky in your set-up or the way you are creating the back-up.

[nowbody]

whats your kernelsize?
i told several times. the image i uploaded has no plugins installed... out of the box... so i dont now...

[judge]

kernel size in image below...

24911

[nowbody]

totalcommander shows me too 7.340.032 for vix backup.
with backupsuit totalcommander shows me: 7.208.960

would you test my uplouded backup-image?

[Larry-G]

as i said backupsuite is a totally different piece of software to the inbuilt image manager in ViX so there is no real point in comparing file sizes for the two.

[judge]

would you test my uplouded backup-image?

download from that site is painfully slow...
set the box up from scratch & try again, works fine here on all builds tried now.

[nowbody]

i tryed some times...
if someone could flash the file successfully than we would now tha backup image is ok.

[nowbody]

faster link http://www.file-upload.net/download-7437816/fail-vusolo2-3.0.632-20130328_165014.rar.html

[Larry-G]

faster link http://www.file-upload.net/download-7437816/fail-vusolo2-3.0.632-20130328_165014.rar.html

dont worry i''ll try your file but it's going to be after 19:00 BST as i'm still at work.

[nowbody]

download from that site is painfully slow...
set the box up from scratch & try again, works fine here on all builds tried now.
build 647 fresh flashed, no plugins, testet:
http://www.file-upload.net/download-7438297/vusolo2-3.0.647-20130407_150109.7z.html
same problem "starting"

[Larry-G]

There is definitely some thing wrong with your backups as i tried to flash the 632 build version and the receiver did not even detect it on the USB stick it just booted into the existing image.

second try i replaced the kernel_cfe_auto from yours with one from my backup, this time the receiver flashed but would not boot up, just sat there with starting on the VFD ( sorry but i dont have a working Null modem cable to generate a bootlog ).

any way i re-flashed the receiver with my own backup made on build 647 and it flashed just fine. so not sure whats going wrong for you but mine creates fully functioning image backups just fine with the inbuilt image manager.

p.s the file size from my kernel_cfe_auto file is identical to your's.

[nowbody]

how do backup your image?
i do "menü" - "VIX" - "Backup image" - "neues Backup"....
without any plugin...

[Larry-G]

blue button> ViX> Image manager> New backup ( green button ).

[nowbody]

blue button> ViX> Image manager> New backup ( green button ).

yes i mean this... so no differences...
i have no idea where the problem is.

[nowbody]

now testet openaaf... backup works without additional app.
but with vix this did not help....
for me openaaf is i bit to much. ;)

[judge]

now testet openaaf... backup works without additional app.
but with vix this did not help....
for me openaaf is i bit to much. ;)
what's the additional app?
can you list your exact image set-up procedure before you make the back up as it's proving pretty hard to repoduce.

[nowbody]

do anybody understand german perhaps you understand me better... ?

first flash new image!
only set sat config. no plugins, no picons.
make a backupimage: blue button> ViX> Image manager> New backup ( green button )
restore backuped image: format usb stick, copy backupimage on it, switch off solo2, plug on usb-stick.

thats all...

[andyblac]

do anybody understand german perhaps you understand me better... ?

first flash new image!
only set sat config. no plugins, no picons.
make a backupimage: blue button> ViX> Image manager> New backup ( green button )
restore backuped image: format usb stick, copy backupimage on it, switch off solo2, plug on usb-stick.

thats all...

can i ask why size usb stick ? it is recommended not to use larger than 8gb

[nowbody]

i used two different usbdrives for flashing. 1gb and 4gb. but usbdrives i only use for flashing. when backing up the image is "made" on the hdd (wd 2,5" 1tb, filesystem: ext4). so i think the usbdrive should not be the problem?

[Larry-G]

i used two different usbdrives for flashing. 1gb and 4gb. but usbdrives i only use for flashing. when backing up the image is "made" on the hdd (wd 2,5" 1tb, filesystem: ext4). so i think the usbdrive should not be the problem?

Try changing the backup location to a USB stick and see if that makes a difference. For reference all my backups are always saved to a mounted USB stick.

Sent from my GT-I9300 using Tapatalk 2

[nowbody]

makes no defference... same problem - display shows "starting"

[nowbody]

still no good news...

[nowbody]

tested the vix backup again. i noticed that now image-backup build a zip-file. zip-file is new i think!
when extracting it kernel file has now the right filesize. Flashing back works too!
now i seams to work fine!

[Larry-G]

tested the vix backup again. i noticed that now image-backup build a zip-file. zip-file is new i think!
when extracting it kernel file has now the right filesize. Flashing back works too!
now i seams to work fine!

yes andy has just put a lot of work into the image manager so that it allows flashing directly from compressed .zip archives and as a result it creates backups in .zipped archives too.

[nowbody]

thanks andyblac for working on the backupmethod!
does anybody know, why backup doesnt work before?

[andyblac]

thanks andyblac for working on the backupmethod!
does anybody know, why backup doesnt work before?

i have recoded the way the kernel is backed-up.