View Full Version : [VU+ Solo2] Cams freezing
is anyone getting a cam freezing ever few hours i use mgcam 1.35 and it locks up for about 5 secounds any ideas does anyone think its the config does anyone have a good config i can try thanks
Have you tried this?
edit mg_cfg file in box type section 'B = from {0} to {6}
Have you tried this?
edit mg_cfg file in box type section 'B = from {0} to {6}
i have that i keep getting
2013-03-31 21:58: Timer Check Enabled
2013-03-31 21:58: Couldn't find MGcamd.1.35a running, Starting MGcamd.1.35a
2013-03-31 22:04: Timer Check Enabled
2013-03-31 22:04: MGcamd.1.35a running OK
any ideas
it keeps stopping starting
2013-03-31 15:55: Timer Check Enabled
2013-03-31 15:55: Couldn't find MGcamd.1.35a running, Starting MGcamd.1.35a
2013-03-31 15:59: Stopping: MGcamd.1.35a
2013-03-31 15:59: Starting MGcamd.1.35a
2013-03-31 16:01: Timer Check Enabled
2013-03-31 16:01: MGcamd.1.35a running OK
2013-03-31 16:07: Timer Check Enabled
2013-03-31 16:07: MGcamd.1.35a running OK
2013-03-31 16:13: Timer Check Enabled
2013-03-31 16:13: MGcamd.1.35a running OK
2013-03-31 16:19: Timer Check Enabled
2013-03-31 16:19: MGcamd.1.35a running OK
2013-03-31 16:25: Timer Check Enabled
2013-03-31 16:25: MGcamd.1.35a running OK
2013-03-31 16:30: Stopping: MGcamd.1.35a
2013-03-31 16:30: Starting MGcamd.1.35a
2013-03-31 16:31: Timer Check Disabled
2013-03-31 16:31: MGcamd.1.35a running OK
2013-03-31 16:39: Stopping: MGcamd.1.35a
2013-03-31 16:39: Starting MGcamd.1.35a
2013-03-31 16:40: Stopping: MGcamd.1.35a
2013-03-31 16:40: Starting MGcamd.1.35a
2013-03-31 16:53: Stopping: MGcamd.1.35a
2013-03-31 16:53: Starting MGcamd.1.35a
as you can see many restarts random..
Hi,
I disabled the 'Enable Frozen Check?' in Menu>Setup>Softcam/CI>Softcam Mananager> Press Menu button and disable. Not sure of the impact of this but it worked for me. Hope it helps.
Stales
Hi,
I disabled the 'Enable Frozen Check?' in Menu>Setup>Softcam/CI>Softcam Mananager> Press Menu button and disable. Not sure of the impact of this but it worked for me. Hope it helps.
Stales
It basically does what the name suggests, ie Checks the cam to see if it is frozen, if yes it restarts the cam.
Disabling this wont do any harm but it does mean that the cam manager no longer monitors for this, as a result if the cam does freeze you will have to manually restart it.
Sent from my GT-I9300 using Tapatalk 2
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.