View Full Version : My et 5000 does not want boot
Due to several power failure in my home, every time when i boot my box it does not respond and give me pale red led.
when i leaved it for 2 or 3 hours, it respond.
the last time, it does not boot till i install vix image 2.2.0 while i was on 2.2.1.
this time, it does not want to accept same image or boot loader.
please help
does any one have suggestion
So which exact image are you trying now ? And if its below 3.0-627 try uodating to that and see what happens.
Sent from my GT-I9300 using Tapatalk 2
i am on vix 2.2.1 and i am trying to install 2.2.0
hi,
the situation changed when i used putty to get crash log.
the 3 led's back to work.
start to install latest boot loader and things go as usual till:
bootloader Linux 2.6.31 UBIFS
booting....
my display freezes on this message .
i tried to install vix image based on this bl but after download the message appear again and red and green led's bright.
tried other images but nothing
so, what can i do
Install the latest image mate, not them old ones> http://www.world-of-satellite.com/enigma2/openvix/index.php?dir=ET-5x00/
Version 3.0 and up needs an updated boot loader if i remember correctly.
hi,
the situation changed when i used putty to get crash log.
the 3 led's back to work.
start to install latest boot loader and things go as usual till:
bootloader Linux 2.6.31 UBIFS
booting....
my display freezes on this message .
i tried to install vix image based on this bl but after download the message appear again and red and green led's bright.
tried other images but nothing
so, what can i do
have you tried this... put the ET5000 folder in the root of a USB stick, put the stick in any of the USB ports then hold the up arrow on the front of the receiver and the new firmware will start flashing
i made a crash log by putty and found :
brcmnand_read_id: CS1: dev_id=ecf10095
After: NandSelect=50000200, nandConfig=15142200
Block size=00020000, erase shift=17
NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
timing1 not adjusted: 5363444f
timing2 not adjusted: 00000fc6
eccLevel=15, 1Ksector=0, oob=16
nbrBitsPerCell=2, cellinfo=0, chip->cellinfo=00000000
<--brcmnand_set_acccontrol: acc b4: d7ff1010, after: d7ff1010
BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS1
Found NAND on CS1: ACC=d7ff1010, cfg=15142200, flashId=ecf10095, tim1=5363444f, tim2=00000fc6
BrcmNAND version = 0x0302 128MB @00000000
B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1
brcmnand_read_id: CS1: dev_id=ecf10095
After: NandSelect=50000200, nandConfig=15142200
Found NAND flash on Chip Select 1, chipSize=128MB, usable size=128MB, base=0
brcmnand_scan: B4 nand_select = 50000200
brcmnand_scan: After nand_select = 50000200
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 3.2 NAND flash size 128MB @18000000
ECC layout=brcmnand_oob_bch4_4k
brcmnand_scan: mtd->oobsize=64
usb 2-1: new high-speed USB device number 2 using ehci-brcm
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_main_descr
Adjust partition complete size from entire device to 7f00000 to avoid overlap with BBT reserved space
Adjust partition rootfs size from entire device to 7900000 to avoid overlap with BBT reserved space
Creating 3 MTD partitions on "brcmnand.0":
0x000000000000-0x000007f00000 : "complete"
0x000000000000-0x000000600000 : "kernel"
0x000000600000-0x000007f00000 : "rootfs"
PM: CP0 COUNT/COMPARE frequency depends on divisor
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 4 ports detected
ata2: SATA link down (SStatus 4 SControl 300)
UBI: max. sequence number: 67
UBI: attached mtd2 to ubi0
UBI: MTD device name: "rootfs"
UBI: MTD device size: 121 MiB
UBI: number of good PEBs: 968
UBI: number of bad PEBs: 0
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 968
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 2/0
UBI: image sequence number: 947646524
ALSA device list:
No soundcards found.
UBI: background thread "ubi_bgt0d" started, PID 47
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 119865344 bytes (117056 KiB, 114 MiB, 944 LEBs)
UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:10.
devtmpfs: mounted
Freeing unused kernel memory: 244k freed
INIT: version 2.88 booting
usbcore: registered new interface driver tpm
/dev/dvb/adapter0/video0: No such file or directory
cat: can't open '/proc/stb/info/boxtype': No such file or directory
ALSA: Restoring mixer settings...
Configuring network interfaces... /usr/sbin/alsactl: load_state:1686: No soundcards found...
bcmemac: eth0 NIC Link is Down
udhcpc (v1.19.4) started
Sending discover...
Sending discover...
Sending discover...
No lease, forking to background
done.
modprobe: FATAL: Error inserting ipv6 (/lib/modules/3.6.0/kernel/net/ipv6/ipv6.ko): Invalid argument
Mounting remote filesystems...
vm.dirty_writeback_centisecs = 300
vm.dirty_background_ratio = 1
vm.min_free_kbytes = 8192
vm.dirty_ratio = 60
INIT: Entering runlevel: 3
Starting system message bus: dbus.
Starting Dropbear SSH server: modprobe: FATAL: Error inserting ipv6 (/lib/modules/3.6.0/kernel/net/ipv6/ipv6.ko): Invalid argument
modprobe: FATAL: Error inserting ipv6 (/lib/modules/3.6.0/kernel/net/ipv6/ipv6.ko): Invalid argument
dropbear.
Starting internet superserver: inetd.
Starting syslogd/klogd: done
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
...done.
/dev/dvb/adapter0/video0: No such file or directory
grep: /etc/enigma2/settings: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
grep: /etc/enigma2/settings: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
grep: /etc/enigma2/settings: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
grep: /etc/enigma2/settings: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
grep: /etc/enigma2/settings: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
grep: /etc/enigma2/settings: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
grep: /etc/enigma2/settings: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
grep: /etc/enigma2/settings: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
grep: /etc/enigma2/settings: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
INIT: Id "gui" respawning too fast: disabled for 5 minutes
INIT: no more processes left in this runlevel
My ET9000 will not install a fresh image if any of the other usb's are in use. Remove every other USB device before flashing.
My ET9000 will not install a fresh image if any of the other usb's are in use. Remove every other USB device before flashing.
i already did but still the same.
does this log means something?
Which VIX build & bootloader are you trying to install?
Hello. I have a et5000 Extrend. I throw some images with usb but it does not restart even though the image gets. . Can you do reboot with telnet, but we only come logos screen image. Has anyone any ideas?
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.