View Full Version : [Solved] ferguson 202e died on me
New to this box.Flushed with patch added line everything ok! set up channel list seemed to be ok.Whent out for a couple of hours returned home turned on box! ON light come on! nothing :confused: all that was on front display (R S H) or (R S K) only had the box 1 day any ideas what this may be software or hardware?
Any help will be appreciated
aasheish_mody
07-09-12, 14:12
It can only be fixed through a null modem cable. Do you have one ?
Thanks for your quick reply. No i dont but have sent unit back anyway! Will enquire with WOS just wanted to know what (R S H) or (R S K) meant??
Thanks for your time :)blueboy
Sounds like something went wrong when you patched the unit, easily recovered with a USB TO RS232 adapter and null modem cable.
Thanks for your reply.Will look into this when the box comes back! :thumbsup:
I also have the decoder with the dispay with rsh, when I go to load the file A202E_20120807_V1.19B1.abs I get the message "please reset target" and hangs what should I do?
sicilian seems the man in the know! if you dont have a USB TO RS232 adapter and null modem cable all i can suggest is phone or email your supplier
Best of luck
blueboy.
check your patch your patch A202E_20120807_V1.19B1.abs the date on the newest patch A202E_20120808_V1.19B1.abs same V number? get patch from download section and give it another try ?
Best of luck
blueboy
I also have the decoder with the dispay with rsh, when I go to load the file A202E_20120807_V1.19B1.abs I get the message "please reset target" and hangs what should I do?
Follow the guide, at that point power on the receiver, if already on, simply power off then on again :)
Follow the guide, at that point power on the receiver, if already on, simply power off then on again :)
But the guide says to turn on the receiver after loading the firmware?
But the guide says to turn on the receiver after loading the firmware?
Read what I posted, I said 'at that point power on the receiver' if already on, power off, then on again.
If not connecting check your RS232 connection is set correctly on your PC.
I solved thanks for your help:)
I solved thanks for your help:)
Good news
How did you solve it ? May help others in the future (ie ME)
blueboy
I solved by following the advice of the Siciliano enough turn the switch on the receiver. Now I have another problem which is almost 3 times the word comes from ASH what can 'depend?
I solved by following the advice of the Siciliano enough turn the switch on the receiver. Now I have another problem which is almost 3 times the word comes from ASH what can 'depend?
You need to RS232 flash the receiver, follow the guide. You patched incorrectly.
After restoring the original firmware with RS232 cable, I installed the patch via the USB port, after a few hours of operation when you switch off the decoder to riaccenzione out the word ASH. this thing 'happened 3 times in 2 days, I hope I was clear.
After restoring the original firmware with RS232 cable, I installed the patch via the USB port, after a few hours of operation when you switch off the decoder to riaccenzione out the word ASH. this thing 'happened 3 times in 2 days, I hope I was clear.
Not experienced A5H here at all, could be something you are doing then. Maybe incorrect channel list? Old patch? Or take back your unit to whoever you purchased from to check.
have same problem ash i have null cable but i do not no how to bring up ariva loder can anyone help
same with me any idea how to get away with reset target
hi,
my ferguson 102e is completely turned off, it doesn't show any message on display.
can you think that recovery with rs232 can resolve it?
thanks.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.