View Full Version : Solo stuck on loading screen
I bought a new VU+ Solo last week, flashed with latest bootloader and Vix image, added bouquet, got CCcam up and running all was good.
However, when I went to use the box last night I was met with a blank screen. On rebooting, the Vix loading screen came up but it would not move beyond this. After a bit of reading on the forum about similar problems I reflashed the image, went through the set up process etc. but, after a scan, it again stuck on the loading screen and would not budge. I tried this a few times with the same result.
Others with similar difficulties have been advised that this may be a warranty issue, but I would appreciate any advice on how I might resolve this before I go down that route.
Re-flash the receiver with latest Solo image here http://www.world-of-satellite.com/enigma2/openvix/index.php?dir=Vu%2BSolo/
Setup fresh and do not restore any backup settings. Also try booting without ethernet cable attached.
Re-flash the receiver with latest Solo image here http://www.world-of-satellite.com/enigma2/openvix/index.php?dir=Vu%2BSolo/
Setup fresh and do not restore any backup settings. Also try booting without ethernet cable attached.
Thanks for the response. Will try flashing with the latest image when I get home, although I flashed with the latest image as of last Thursday, I think. I've already tried rebooting with the ethernet cable removed, but this made no difference.
Will report back once I try the latest image.
One last thing, are you 100% sure the new image flashed? Do you check the LED status? Also did you get the start up wizard after the loading screen? http://www.world-of-satellite.com/showthread.php?1148-How-to-flash-your-VU-Solo-with-USB-stick
One last thing, are you 100% sure the new image flashed? Do you check the LED status? Also did you get the start up wizard after the loading screen? http://www.world-of-satellite.com/showthread.php?1148-How-to-flash-your-VU-Solo-with-USB-stick
Yes, I went through the flashing process and ended up with the flashing green LED. I got the start up wizard and was able to set preferences but after the satellite scan I was left stuck on the loading screen.
Yes, I went through the flashing process and ended up with the flashing green LED. I got the start up wizard and was able to set preferences but after the satellite scan I was left stuck on the loading screen.
That is 100% correct, after that you either have to upload channel settings/bouquets or run a manual satellite scan.
basilyoung
21-05-12, 13:41
is the unit unresponsive, ie, if you reboot, ( minus any usb,s ) does it boot up at all?
That is 100% correct, after that you either have to upload channel settings/bouquets or run a manual satellite scan.
I will go this process again, but after running a scan, nothing appeared. Perhaps I ran an automatic scan - would that make a difference?
is the unit unresponsive, ie, if you reboot, ( minus any usb,s ) does it boot up at all?
It boots (minus usbs) as far as the loading screen and I can access the menu via the menu button.
It boots (minus usbs) as far as the loading screen and I can access the menu via the menu button.
Like I said above, you need to either run a manual satellite scan or upload channel settings/bouqets.
Guys - all is now well. I just added in my bouquet again and the channels reappeared. Apologies for troubling you and being such a noob. All your advice was much appreciated. Many thanks.
Guys - all is now well. I just added in my bouquet again and the channels reappeared. Apologies for troubling you and being such a noob. All your advice was much appreciated. Many thanks.
No need to apologize, that's why were here, to help those who need our help.
Sent from my HTC Desire using Tapatalk 2
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.