View Full Version : Xtrend ET-5000 with bootloader 2.6.31
Hi,
To install last PLi 2.1 image i load the boatloader 2.6.31 in myxtrend receiver. If i want flash again and install the vix 2.2.100 image i could do or i have install the kernel 2.6.18?
Best regards
Just flash with ViX, bootloader loader is backwards compatible.
Hi,
Many thanks. A few minutes when i tried flash, the vix image was note installed. With the bootloader 2.6.31 instaled, the vix folder must have the name et5000 or et5x00?
Regards
ET5000 and you need to press up on the front radial buttons after powering off and than on.
Flashing instructions here http://www.world-of-satellite.com/showthread.php?8141-How-to-flash-Upgrade-ET5000-via-USB-memory-stick
@ sicillian,
I load the new boatloader 2.6.31 in my xtrend et5000 receiver, now i have only the first page witch " BOOTLOADER LINUX 2.6.31.UBIFS BOOTING ....."
Wat I can do ? I can't flashing a new image animore.
Thx,
MAJOOR
@ sicillian,
I load the new boatloader 2.6.31 in my xtrend et5000 receiver, now i have only the first page witch " BOOTLOADER LINUX 2.6.31.UBIFS BOOTING ....."
Wat I can do ? I can't flashing a new image animore.
Thx,
MAJOOR
check your flash files are correct.
Hi,
This happen with me and i could flash the last PLI 2.1 image.
Best regards
@ sicillian,
I load the new boatloader 2.6.31 in my xtrend et5000 receiver, now i have only the first page witch " BOOTLOADER LINUX 2.6.31.UBIFS BOOTING ....,."
Wat I can do ? I can't flashing a new image animore.
Thx,
MAJOOR
I have put the last pli 2.1 in folder et5000 on pendriver
I put the pendriver in the front usb and then press up on the front radial buttons after powering off and than on .
the pendriver blinkect few time and then stop. The same screen witch " BOOTLOADER LINUX 2.6.31.UBIFS BOOTING ....."
MAJOOR
I have put the last pli 2.1 in folder et5000 on pendriver
I put the pendriver in the front usb and then press up on the front radial buttons after powering off and than on .
the pendriver blinkect few time and then stop. The same screen witch " BOOTLOADER LINUX 2.6.31.UBIFS BOOTING ....."
MAJOOR
Hi,
At this moment i have this problem. I restarted the receiver and always appear the message " BOOTLOADER LINUX 2.6.31.UBIFS BOOTING .....". After some minutes the screen is green. I tried everything, flashing the receiver with several images, but i canīt solve this problem.
This happened after disconnecting all cables from the receiver to change the location of receiver in my room. After that always BOOTLOADER LINUX 2.6.31.UBIFS BOOTING ....."
Anyone could help me, please!!!!!!
Best regards
silverfox0786
16-03-12, 20:17
this happened to one of our mods a few days ago and what i advised him worked so you could try it
get the latest bootloder and place it into file et5x00 [not et5000]
insert USB stick and press the oposite button to initiate flash
so i think that up arrow ley
the bootloder will reflash onto box [normally pressing down wont flash it]
once done get latest public ViX image and flash that
but this time go the normal flashing route of pressing down arrow
things should be sorted
if i got up and down wrong then sorry but its one or the other
this happened to one of our mods a few days ago and what i advised him worked so you could try it
get the latest bootloder and place it into file et5x00 [not et5000]
insert USB stick and press the oposite button to initiate flash
so i think that up arrow ley
the bootloder will reflash onto box [normally pressing down wont flash it]
once done get latest public ViX image and flash that
but this time go the normal flashing route of pressing down arrow
things should be sorted
if i got up and down wrong then sorry but its one or the other
Hi,
Many thanks for your replay.
When you tell "insert USB stick and press the oposite button to initiate flash", the oposit button is the down button or the normal up button to start the flash?
Best regards
silverfox0786
17-03-12, 13:02
yes just had a check
Normal flash method is to press UP ARROW
you need to press DOWN ARROW to flash bootloder and then
when flashing image do it normal way by pressing UP ARROW
yes just had a check
Normal flash method is to press UP ARROW
you need to press DOWN ARROW to flash bootloder and then
when flashing image do it normal way by pressing UP ARROW
I follow your recomendations but the problem. However something was writed in flash, because now donīt appear the xtrend symbol with message "booting 2.6.31. Now appears " OPENVIX VIRTUOSO IMAGE XTREME www.xtrend-support.co.uk. Minutes after again the green screen and always the lights green and red in the receiver display.
I installed the bootloder 3.1.0 and vix 2.3.133.
Any sugestion now?
Best regards
silverfox0786
17-03-12, 15:23
I follow your recomendations but the problem. However something was writed in flash, because now donīt appear the xtrend symbol with message "booting 2.6.31. Now appears " OPENVIX VIRTUOSO IMAGE XTREME www.xtrend-support.co.uk (http://www.xtrend-support.co.uk). Minutes after again the green screen and always the lights green and red in the receiver display.
I installed the bootloder 3.1.0 and vix 2.3.133.
Any sugestion now?
Best regards
if the slash has changed to VIX then look like you flashed the vix image using down arrow instead of bootloader
the other thing to ask is why are you installing 133 latest build is 204
if the slash has changed to VIX then look like you flashed the vix image using down arrow instead of bootloader
the other thing to ask is why are you installing 133 latest build is 204
Hi again,
I donīt find a vix image with version 204. Are in forum?
After flash bootloader with lower button i flas the image vix through normal way, up button, but all remained equal. After that i tried flash vix image with lower button and after appear the text of vix image. Despite of that the problem still, and no image are loaded.
I donīt know how i can solve this problem.
Best regards
silverfox0786
17-03-12, 19:47
last post in this thread
http://www.world-of-satellite.com/showthread.php?13649-ViX-Team-ET5x00-Image-v2-3-Image-releases
last post in this thread
http://www.world-of-satellite.com/showthread.php?13649-ViX-Team-ET5x00-Image-v2-3-Image-releases
Hi again,
A few moments ago i flash again the receiver with bootloader 3.1.0 with lower buton and after flash the vix image 204 with upon button but not solve the problem. Now always appear OPENVIX VIRTUOSO IMAGE XTREME www.xtrend-support.co.uk and after green scree.
I think the receiver are not ok. They could have a serious problem in motherboard or other component.
Best regards
silverfox0786
18-03-12, 00:49
can you get a rs232 bootup report so we can see what it could be
also if you can ftp to box can you get the crash reports
also is it a green screen yr having or is it a black screen crash loop
can you get a rs232 bootup report so we can see what it could be
also if you can ftp to box can you get the crash reports
also is it a green screen yr having or is it a black screen crash loop
Hi again,
Thanks again for your help and feedback. I apreciate!!
I have a rs232 cable null modem but i donīt have any tool or software to make an error report. By ftp i tried with program DCC, but the netwaork is not ok.
After appear the text of VIX IMAGE, the screen still with green color (not black).
I would like to know how i can do anything by output rs232 and null modem cable?
Best regards
silverfox0786
18-03-12, 17:57
use putty and and
connect the null modem cable
for the setup in putty
select serial
change COM1 to what ever com port yr on
then the baudrate [port]
select 115200
select open
and start yr box
use putty and and
connect the null modem cable
for the setup in putty
select serial
change COM1 to what ever com port yr on
then the baudrate [port]
select 115200
select open
and start yr box
Hi again,
I select serial, port com 1, speed (baud)=115200, data bits=8, stop bits=1, parity none and flow control= xon/xoff and select open. I turn on the receiver but anything happen. I do anything wrong?
Best regards
silverfox0786
18-03-12, 22:14
use putty its easier and no so many settings to address
use putty its easier and no so many settings to address
Hi,
Ok, i understand, but i do exactly your configurations and turn on the receiver, but nothing happens. Maybe the receiver not respond.
Best regards
Hi again,
Hi achieve the report of my xtrend with putty software. This is the report. If you can help me to decode the information, i apreciate.
IR RC6 protocol handler initialized
IR JVC protocol handler initialized
IR Sony protocol handler initialized
IR RC5 (streamzap) protocol handler initialized
IR MCE Keyboard/mouse protocol handler initialized
IR LIRC bridge handler initialized
Bluetooth: Generic Bluetooth USB driver ver 0.6
usbcore: registered new interface driver btusb
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
ALSA device list:
No soundcards found.
TCP cubic registered
NET: Registered protocol family 17
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
lib80211: common routines for IEEE802.11 drivers
EBI CS1: setting up NAND flash (primary)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000000
B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1
brcmnand_read_id: CS1: dev_id=ecf10095
After: NandSelect=50000200, nandConfig=15142200
Block size=00020000, erase shift=17
NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
timing1 not adjusted: 5363444f
timing2 not adjusted: 00000fc6
eccLevel=15, 1Ksector=0, oob=16
nbrBitsPerCell=2, cellinfo=0, chip->cellinfo=00000000
<--brcmnand_set_acccontrol: acc b4: d7ff1010, after: d7ff1010
BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS1
Found NAND on CS1: ACC=d7ff1010, cfg=15142200, flashId=ecf10095, tim1=5363444f, tim2=00000fc6
BrcmNAND version = 0x0302 128MB @00000000
B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1
brcmnand_read_id: CS1: dev_id=ecf10095
After: NandSelect=50000200, nandConfig=15142200
Found NAND flash on Chip Select 1, chipSize=128MB, usable size=128MB, base=0
brcmnand_scan: B4 nand_select = 50000200
brcmnand_scan: After nand_select = 50000200
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 3.2 NAND flash size 128MB @18000000
ECC layout=brcmnand_oob_bch4_4k
brcmnand_scan: mtd->oobsize=64
usb 2-1: new high-speed USB device number 2 using ehci-brcm
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_main_descr
Adjust partition complete size from entire device to 7f00000 to avoid overlap wi th BBT reserved space
Adjust partition rootfs size from entire device to 7900000 to avoid overlap with BBT reserved space
Creating 3 MTD partitions on "brcmnand.0":
0x000000000000-0x000007f00000 : "complete"
0x000000000000-0x000000600000 : "kernel"
0x000000600000-0x000007f00000 : "rootfs"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
ata2: SATA link down (SStatus 4 SControl 300)
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 4 ports detected
UBI: max. sequence number: 170
UBI: attached mtd2 to ubi0
UBI: MTD device name: "rootfs"
UBI: MTD device size: 121 MiB
UBI: number of good PEBs: 967
UBI: number of bad PEBs: 1
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 967
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 2/0
UBI: image sequence number: 41218595
UBI: background thread "ubi_bgt0d" started, PID 40
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 119738368 bytes (116932 KiB, 114 MiB, 943 LEBs)
UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:12.
Freeing unused kernel memory: 252k freed
INIT: version 2.86 booting
Please wait: booting...
Root filesystem already rw, not remounting
usbcore: registered new interface driver tpm
modloader: module license 'PROPRIETARY' taints kernel.
Disabling lock debugging due to kernel taint
r8712u: module is from the staging directory, the quality is unknown, you have b een warned.
/dev/dvb/adapter0/video0: No such file or directory
cat: can't open '/proc/stb/info/boxtype': No such file or directory
ALSA: Restoring mixer settings...
Configuring network interfaces... bcmemac: eth0 NIC Link is Down
eth0 no wireless extensions.
udhcpc (v1.18.5) started
Sending discover...
Sending discover...
Sending discover...
No lease, forking to background
done.
Starting portmap daemon: portmap.
Mounting remote filesystems...
modprobe: FATAL: Error inserting ipv6 (/lib/modules/3.1.0/kernel/net/ipv6/ipv6.ko): Invalid argument
vm.dirty_writeback_centisecs = 300
vm.dirty_background_ratio = 1
vm.dirty_ratio = 60
INIT: Entering runlevel: 3
Starting system message bus: dbus.
Starting Dropbear SSH server: modprobe: FATAL: Error inserting ipv6 (/lib/modules/3.1.0/kernel/net/ipv6/ipv6.ko): Invalid argument
modprobe: FATAL: Error inserting ipv6 (/lib/modules/3.1.0/kernel/net/ipv6/ipv6.ko): Invalid argument
dropbear.
starting Busybox Periodic Command Scheduler: crond... done.
Starting internet superserver: inetdcrond[255]: crond: crond (busybox 1.18.5) started, log level 8
.
sh: bad number
creating NFS state directory: done
mounting /proc/fs/nfsd: modprobe: FATAL: Error inserting nfsd (/lib/modules/3.1.0/kernel/fs/nfsd/nfsd.ko): Invalid argument
mount: mounting nfsd on /proc/fs/nfsd failed: No such device
done
starting 8 nfsd kernel threads: done
starting mountd: done
starting statd: done
exportfs: Warning: /media/hdd2/ does not exist
exportfs: Warning: /media/usb/ does not exist
Starting Samba: smbd nmbdmodprobe: FATAL: Error inserting ipv6 (/lib/modules/3.1.0/kernel/net/ipv6/ipv6.ko): Invalid argument
modprobe: FATAL: Error inserting ipv6 (/lib/modules/3.1.0/kernel/net/ipv6/ipv6.ko): Invalid argument
.
Starting syslogd/klogd: done
* starting FTP Server: vsftpd... done.
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon [ ok ]
/dev/dvb/adapter0/video0: No such file or directory
grep: /etc/enigma2/settings: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
grep: /etc/enigma2/settings: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
grep: /etc/enigma2/settings: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
grep: /etc/enigma2/settings: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
grep: /etc/enigma2/settings: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
grep: /etc/enigma2/settings: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
grep: /etc/enigma2/settings: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
grep: /etc/enigma2/settings: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
/dev/dvb/adapter0/video0: No such file or directory
grep: /etc/enigma2/settings: No such file or directory
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
INIT: Id "gui" respawning too fast: disabled for 5 minutes
Best regards
silverfox0786
18-03-12, 23:41
Second to the bottom
Segmentaion Fault
A segmentation fault (often shortened to segfault), bus error or access violation is generally an attempt to access memory that the CPU cannot physically address. It occurs when the hardware notifies an operating system about a memory access violation. The OS kernel then sends a signal to the process which caused the exception. By default, the process receiving the signal dumps core and terminates. The default signal handler can also be overridden to customize how the signal is handled.
silverfox0786
18-03-12, 23:44
whilst connect to network can you access the box via telnet
if you can can you give us the output after typing this
init 4
enigma2
whilst connect to network can you access the box via telnet
if you can can you give us the output after typing this
init 4
enigma2
Sorry but this part i donīt understand? During the putty report i must conect to the receiver by telnet or use putty software to conecto receiver by telnet?
Sorry!
Regards
silverfox0786
18-03-12, 23:56
log into the receiver via LAN using putty or DCC if thats what you use and send the command
init 4
then
enigma2
log into the receiver via LAN using putty or DCC if thats what you use and send the command
init 4
then
enigma2
Hi,
I have xtrend linked with my router by ethernet cable. However with dcc the network is not ok and because of that i can entry by telnet into the receiver. Appear "server closed" in the ip of xtrend.
In your opinion it is possible solve the problem of segmention faulty?
Best regards
silverfox0786
19-03-12, 03:49
yr framebuffer is not being loaded and hence yr getting segfault
you need to look into that to find a solution
yr framebuffer is not being loaded and hence yr getting segfault
you need to look into that to find a solution
Hi,
Thanks for your replay! Probably is better sent te receiver to a official supporter because i think i donīt have enough knowledge to solve this problem.
Best regards
yr framebuffer is not being loaded and hence yr getting segfault
you need to look into that to find a solution
Hi,
With putty or other software and null modem cable is not possible flash or sent any firmware to the receiver?
Best regards
silverfox0786
19-03-12, 11:53
Hi,
Thanks for your replay! Probably is better sent te receiver to a official supporter because i think i donīt have enough knowledge to solve this problem.
Best regards
i would say yes send it off for repair if your not sure
Hi,
With putty or other software and null modem cable is not possible flash or sent any firmware to the receiver?
Best regards
Xtrend does not have null modem NFI flashing
i would say yes send it off for repair if your not sure
Xtrend does not have null modem NFI flashing
Hi again,
Many thanks for your help. I will sent tomorrow the receiver for repair. I received today the response from seller and the warranty will be activated.
Best regards
silverfox0786
19-03-12, 14:52
glad yr seller is happy to do a waranty repair
hope it gets sorted soon
Guyīs today I tried to update mates ET5000 and Iīm having same problem, however when I type in init4 and then enigma2 I get:
Welcome to ViX for et5x00
ViX v2.3
et5x00 login: root
root@et5x00:~# init 4
root@et5x00:~# enigma2
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
Can anyone help as worried I have "bricked" his box. I can access the box both with putty and cuteTP. Been at it since 1pm today.... No hair left to pull.
Thanks
John
Hi,
At this moment i have this problem. I restarted the receiver and always appear the message " BOOTLOADER LINUX 2.6.31.UBIFS BOOTING .....". After some minutes the screen is green. I tried everything, flashing the receiver with several images, but i canīt solve this problem.
This happened after disconnecting all cables from the receiver to change the location of receiver in my room. After that always BOOTLOADER LINUX 2.6.31.UBIFS BOOTING ....."
Anyone could help me, please!!!!!!
Best regards
have you done this... put the ET5000 folder in the root of a USB stick, put the stick in any of the USB ports then hold the up arrow on the front of the receiver and the new firmware will start flashing
Guyīs today I tried to update mates ET5000 and Iīm having same problem, however when I type in init4 and then enigma2 I get:
Welcome to ViX for et5x00
ViX v2.3
et5x00 login: root
root@et5x00:~# init 4
root@et5x00:~# enigma2
PYTHONPATH: /usr/lib/enigma2/python
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
/dev/fb0: No such file or directory
+ (9) GFBDC
/dev/fb0: No such file or directory
framebuffer not available.
FATAL: no framebuffer available
Segmentation fault
Can anyone help as worried I have "bricked" his box. I can access the box both with putty and cuteTP. Been at it since 1pm today.... No hair left to pull.
Thanks
John
And I have the same problem. I tried 30 images but the screen remains green. Is dead?
Thanks
the problem is here:-
ViX v2.3
please flash the latest apollo build 95.
As rossi said ViX 2.3 is something like three years old, no longer has any feeds nor a build GIT. if you want to use a newer image you need to reflash the receiver with a USB stick it can not be done online.
Please explain me better. I tried and ViX-2.3.GM-et5x00_usb, but the same problem.
Thanks
go to openvix.co.uk and download the latest Apollo image from there.
Nothing and with this image. Not exist any tool for RS232 cable to upload this image?
go to openvix.co.uk and download the latest Apollo image from there.
Thankkkk U rossi I love you.
FIXED with latest apolo vix image in my case I have ET4000 with three lights no booting enigma2 problem only xtrend logo on tv
with crashlog no framebuffer available I have test all ET4000 images openpli,openatv, factory original image also bootloaders but simple fixed with this apolo vix openvix-Apollo.166-et4x00_usb
I am very very happy you save 100 euros to me.
You make my day.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.