How to Install CCcam/MGCamd/Others on ViX image GiGablue, Technomate, Venton, VU+

[punisher]

How to Install CCcam/MGCamd/Others on Duo/Solo/Uno/ET9000/ET5000

In this example im going to show how to Install CCcam 2.2.1 on the ViX Image
You need access to FTP and CCcam 2.2.1 (or whichever version you prefer) ipk file and your CCcam.cfg file (your details go in here)

I use FlashFXP (Filezilla is a great free one too) and below is how I have configured mine, you will need to do the same for yours

You need your boxs IP Address/Host Name, Username and Pass in order to connect to your box

fxpsite.jpg

As you can see my IP Address/Host Name is xxxxx.dyndns.org or i could have entered 192.168.x.12
my username is root (that is default)
my password is xxxxxxxxx (default password is blank or password or dreambox)

once you have saved and connected to the box you should get access to the root of your box and should look like the right hand window of the below screenshot

fxpftp.jpg

Download your Cam from

Please register to view content. Only take's a few seconds!

Im after CCcam 2.2.1 which is enigma2-plugin-cams-cccam.2.2.1_1.0-r0_mipsel
Once downloaded you need to transfer the enigma2-plugin-cams-cccam.2.2.1_1.0-r0_mipsel.ipk file into the /tmp folder on the box like below

cam.jpg

Then transfer your CCcam.cfg file into the /etc/ folder

etc.jpg

now go to your box and press Menu/Setup/System/VIX/Install Local Extension and you should have enigma2-plugin-cams-cccam.2.2.1_1.0-r0_mipsel.ipk file in there

1.jpg

Press "Green" button to install and once completed it will ask for a "Gui Restart". Press OK and wait for box to come back on
Once the box is on press Menu/Setup/Softcam / CI/Softcam Manager and in there if you have done everything correctly you should see CCcam 2.2.1

2.jpg

Press "Green" to start CCcam 2.2.1 and it should now be active like below

3.jpg

Finally Press "Blue" to enable Auto Start and you are now ready and setup with CCcam 2.2.1

4.jpg

Hope you guys find this tutorial helpful any questions dont hesitate to ask in here

[bassethound]

Great tutorial punisher im going to make this a sticky

[johno]

thankyou topman


johno

[punisher]

no probz guys thought it might come handy for people

[notanotherone]

no probz guys thought it might come handy for people

why did you look at me when you wrote this


nice post mate much appreciated i can assure you

[punisher]

lmao no lookin in any directions just pointin ^^^^^^^^

[gothicpsyko]

Hi folks!
Im noob and had a dvb 500 before where i used mgcamd 1.35a
For my needs i have to get this cam work. now i use the newest ccam 2.2.1 and yes it works! but not god enough for my needs!
i have installed mgcamd 1.35a downloaded from4shared!
First i had it installed and almost every location i put my newcamd.list, newcamd.cfg, mgcam.list, mgcam.cfg"i tryed many names" it will not start and say i had to put my config in var/keys
At least i found some other files the mgcam needs, havent found it here in the forum. files like the mg_cfg.fil and some others! now im so long that the mgcam will start! but now a new error is showing up!
Cannot parse the emu.
i use the newst vix image.
i there anyone who use a mgcamd 1.35a and can give me an step by step tutorial what to install, where to place which files, what the files should be named and so on! i have tryed for days and cannot get it to work!
im a noob, on my dvb 500 i had to install the mgcamd and then just too place my newcamd list file ! why is this so complicated on my vu+ duo

Thx for help allready jet!

[Alias1]

Binary /usr/softcams
/etc/keys/ mg_cfg and newcamd.list

[gothicpsyko]

ok i will try that
what are the binary files ?
mg_cfg i have nad newcamd.list i have

[pheonix]

binary files are the .bin files.
if you installed the cam from the 4shared ipk files you should not need to worry about that as it should already be in the correct place.