Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Results 1 to 15 of 15

Thread: Problem reinstalling Remote channel stream converter after software upgrade

  1. #1

    Title
    Forum Supporter
    Donated Member
    Join Date
    Dec 2014
    Posts
    188
    Thanks
    15
    Thanked 7 Times in 7 Posts

    Problem reinstalling Remote channel stream converter after software upgrade

    I am running remote channel stream converter between an Xtrend ET10000 master and an ET 7000 slave. After stupidly updating Openvix to 5.1.11 on the slave, I am unable to reinstall the remote channel stream.

    I can see the ET10000 when I browse the network with the ET7000 slave and I have inputted the same IP number into the remote channel stream interface. The ET10000 does not have a password, so I have left this blank. I have left all the other entries at their default values. (host user name “root”, host streaming port “08001”, host FTP port “00021”.

    When I reboot after going into client mode and entering the IP address of the ET10000, the ET7000 seems to hang up. I gave it about 10 minutes, but nothing happened except the wait message and the moving “Vix” sign. This repeats. The only way out seems to be to reflash.
    Rebooting the client without going into remote channel stream converter works OK.

    Does anyone know what I am doing wrong, or have suggestions?

    Many thanks.

  2. #2
    twol's Avatar
    Title
    Moderator
    Join Date
    Apr 2012
    Posts
    8,383
    Thanks
    987
    Thanked 2,888 Times in 2,243 Posts
    Option 1: turn on debug log and post it here.
    Option 2: flash clean and when the wizard gets to tuner, select client mode and hopefully that will do everything for you ... no need for the RCSC plgin
    Gigablue Quad 4K & UE 4K
    .........FBC Tuners:
    ------------------> DUR-Line DCR 5-1-8-L4 Multiswitch to 1.5M dish(28.2E)
    ------------------> Spaun SUS 5581/33 NFA Multiswitch to 80 cm dish(19.2E)
    .......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
    AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using Legacy ports on multiswitches
    Zgemma H9 C/S into Giga4K

  3. #3

    Title
    Forum Supporter
    Donated Member
    Join Date
    Dec 2014
    Posts
    188
    Thanks
    15
    Thanked 7 Times in 7 Posts
    Thanks twol.
    I have been following Option 2 all along.
    Tonight I will try flashing, turning on the debug log and repeating Option 2.

  4. #4

    Title
    Forum Supporter
    Donated Member
    Join Date
    Dec 2014
    Posts
    188
    Thanks
    15
    Thanked 7 Times in 7 Posts
    By the way, if the box hangs during rebooting after I follow Option 2 and I have to reflash again, won't the debug log be destroyed?

  5. #5

    Title
    Forum Supporter
    Donated Member
    Join Date
    Dec 2014
    Posts
    188
    Thanks
    15
    Thanked 7 Times in 7 Posts
    By the way, if the box hangs during rebooting after I follow Option 2 and I have to reflash again, won't the debug log be destroyed?

  6. #6

    Title
    Forum Supporter
    Donated Member
    Join Date
    Dec 2014
    Posts
    188
    Thanks
    15
    Thanked 7 Times in 7 Posts
    Here is a debug log
    Attached Files Attached Files

  7. #7
    Sicilian's Avatar
    Title
    The Boss
    Join Date
    Mar 2010
    Posts
    29,645
    Thanks
    23,575
    Thanked 26,044 Times in 7,633 Posts
    Personally I'd advise to install 'Channels Importer' plugin, better than RCSC.

    Install via plugins > System plugins.
    D I S C L A I M E R

    My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!

    Follow us on Twitter 0penViX
    Rules can be found
    HERE
    Support our sponsor World-Of-Satellite
    HERE
    GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
    Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable





  8. #8
    twol's Avatar
    Title
    Moderator
    Join Date
    Apr 2012
    Posts
    8,383
    Thanks
    987
    Thanked 2,888 Times in 2,243 Posts
    Quote Originally Posted by George Kildare View Post
    Here is a debug log
    So to answer the log question, save log to usb(HDD not flash!
    The debug log posted shows:
    < 977.447> [ChannelsImporter][checkEPG] Force EPG save on remote receiver...
    < 977.448> [ChannelsImporter][saveEPGonRemoteReceiver] URL: http://0.0.0.0/api/saveepg
    < 977.474> [ChannelsImporter][saveEPGonRemoteReceiver] ERROR: 146

    the url should contain the host server IP address and its 0.0.0.0

    lastly, use putty to telnet to the receiver, and enter init 4 then ftp to the box, pull off the etc/enigma2/settings file and post what you have for: (these are my values for one of my boxes and should be near the top of the settings file)
    config.clientmode.enabled=True
    config.clientmode.nim_cache=[{"configMode": "nothing"}]
    config.clientmode.serverIP=192.168.0.175

    if the last is 0.0.0.0 change it to the host IP, save file and ftp back to the receiver .... then in the putty telnet session enter init 6 to reboot the box.
    Gigablue Quad 4K & UE 4K
    .........FBC Tuners:
    ------------------> DUR-Line DCR 5-1-8-L4 Multiswitch to 1.5M dish(28.2E)
    ------------------> Spaun SUS 5581/33 NFA Multiswitch to 80 cm dish(19.2E)
    .......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
    AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using Legacy ports on multiswitches
    Zgemma H9 C/S into Giga4K

  9. #9
    bellejt's Avatar
    Title
    Senior Member
    Join Date
    Dec 2013
    Posts
    1,721
    Thanks
    58
    Thanked 316 Times in 272 Posts
    why don't you use fallback tuner ?
    VU+ DUO2 quad tuner with HDD 1 TB + Latest Openvix and VU+ DUO2 FB tuner + Octagon SF8008 FB tuner
    Triax 88 cm rotor single LNB 30 E- 40 W
    1 Gibertini 1.00 m fixed - 3 quad LNB 19E-23.5E-28.2E

  10. #10
    twol's Avatar
    Title
    Moderator
    Join Date
    Apr 2012
    Posts
    8,383
    Thanks
    987
    Thanked 2,888 Times in 2,243 Posts
    Quote Originally Posted by bellejt View Post
    why don't you use fallback tuner ?
    .... I know I shouldn't answer .... but client mode is better!!
    Gigablue Quad 4K & UE 4K
    .........FBC Tuners:
    ------------------> DUR-Line DCR 5-1-8-L4 Multiswitch to 1.5M dish(28.2E)
    ------------------> Spaun SUS 5581/33 NFA Multiswitch to 80 cm dish(19.2E)
    .......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
    AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using Legacy ports on multiswitches
    Zgemma H9 C/S into Giga4K

  11. #11

    Title
    Forum Supporter
    Donated Member
    Join Date
    Dec 2014
    Posts
    188
    Thanks
    15
    Thanked 7 Times in 7 Posts
    I'll try the "Channel Importer" plug-in with "Fallback Tuner" first. I have installed the plug-in, but cannot seem to find the channel importer plug-in in the new menu structure. What is its location?

  12. #12

    Title
    Forum Supporter
    Donated Member
    Join Date
    Dec 2014
    Posts
    188
    Thanks
    15
    Thanked 7 Times in 7 Posts
    Sorry. I've found it.

  13. #13
    twol's Avatar
    Title
    Moderator
    Join Date
    Apr 2012
    Posts
    8,383
    Thanks
    987
    Thanked 2,888 Times in 2,243 Posts
    Quote Originally Posted by George Kildare View Post
    I'll try the "Channel Importer" plug-in with "Fallback Tuner" first. I have installed the plug-in, but cannot seem to find the channel importer plug-in in the new menu structure. What is its location?
    The ChannelImporter plugin was the precursor for Client mode and in my view a step backwards.
    Fallbacktuner is a stepbackwards from that.
    I used fallback tuner for several years, manipulated the bouquets on my main box and then copied to the the client box using remote fallback.
    Client server does all this for you automatically.
    RCSC is an alternative, but ends up with a importing another version of your servers bouquets.

    All of them work, but some require more effort than others.
    I just re-installed CS mode on my ET7500 to check out and it worked perfectly and took just a couple of minutes (if that) to enable the ET7500 to run a copy of my Giga4K setup on the ET7500.
    Last edited by twol; 22-01-18 at 19:14.
    Gigablue Quad 4K & UE 4K
    .........FBC Tuners:
    ------------------> DUR-Line DCR 5-1-8-L4 Multiswitch to 1.5M dish(28.2E)
    ------------------> Spaun SUS 5581/33 NFA Multiswitch to 80 cm dish(19.2E)
    .......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
    AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using Legacy ports on multiswitches
    Zgemma H9 C/S into Giga4K

  14. #14

    Title
    Forum Supporter
    Donated Member
    Join Date
    Dec 2014
    Posts
    188
    Thanks
    15
    Thanked 7 Times in 7 Posts
    "Channel Importer" plug-in works for me. That is the easiest solution for now. Very many thanks both bellejt and twol. Much appreciated.

  15. The Following User Says Thank You to George Kildare For This Useful Post:

    twol (22-01-18)

  16. #15
    twol's Avatar
    Title
    Moderator
    Join Date
    Apr 2012
    Posts
    8,383
    Thanks
    987
    Thanked 2,888 Times in 2,243 Posts
    No problem — enjoy
    Gigablue Quad 4K & UE 4K
    .........FBC Tuners:
    ------------------> DUR-Line DCR 5-1-8-L4 Multiswitch to 1.5M dish(28.2E)
    ------------------> Spaun SUS 5581/33 NFA Multiswitch to 80 cm dish(19.2E)
    .......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
    AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using Legacy ports on multiswitches
    Zgemma H9 C/S into Giga4K

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.