One other think to try. If I understand correctly you are using 007. iirc 007 supports couch flashing on arm boxes. Blue button > vix > image manger. Try flashing via this.
Sent from my iPhone using Tapatalk
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
On my router I can list all attached boxes and their IP addresses...... is that possibke in your environment.
Just wondering if the box initially is not using the IP address you expect
Gigablue Quad 4K & UE 4K
.........FBC Tuners:
------------------> GT-Sat unicable LNB to 1.5M dish(28.2E)
------------------> Gigablue unicable LNB to 80 cm dish(19.2E)
.......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using unicable ports
Zgemma H9 C/S into Giga4K
Flash 009 release worked for me.
OK, I have a fritzbox, that fixes static IP‘s on request (typical German technology), but always starts with another DHCP assigned IP when you have flashed a new image.
So try to find out what has been assigned..... I have rarely not been able to telnet into my boxes to find out what is going on.... unless the box is as dead as a dodo
If you can then telnet , login, init 4 and then enter enigma2 to see the inital log)
Gigablue Quad 4K & UE 4K
.........FBC Tuners:
------------------> GT-Sat unicable LNB to 1.5M dish(28.2E)
------------------> Gigablue unicable LNB to 80 cm dish(19.2E)
.......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using unicable ports
Zgemma H9 C/S into Giga4K
openATV on the German forum report unable to boot with drivers from 24/Dec/17!
Last edited by twol; 03-01-18 at 22:52.
Gigablue Quad 4K & UE 4K
.........FBC Tuners:
------------------> GT-Sat unicable LNB to 1.5M dish(28.2E)
------------------> Gigablue unicable LNB to 80 cm dish(19.2E)
.......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using unicable ports
Zgemma H9 C/S into Giga4K
so i just tried again with the above suggestions & still got the stuck in boot mode & i also tried to telnet to the box via filezilla & it would not let me connect even though i was using the correct ip addy so it must be down to that drive issue.
Gigablue Quad 4K & UE 4K
.........FBC Tuners:
------------------> GT-Sat unicable LNB to 1.5M dish(28.2E)
------------------> Gigablue unicable LNB to 80 cm dish(19.2E)
.......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using unicable ports
Zgemma H9 C/S into Giga4K