Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Page 1 of 2 12 LastLast
Results 1 to 15 of 19

Thread: Dish not Moving

  1. #1

    Title
    Member
    Join Date
    Jan 2015
    Posts
    45
    Thanks
    1
    Thanked 3 Times in 3 Posts

    Dish not Moving

    I have just partially set up my new receiver, but cannot configure it to move my motorised dish. Its receiving power OK, as I can move it outside the house by pressing the buttons on the mount. Also, after moving it this way and tuning in to a TV channel, the receiver automatically moves the dish to pick up the channel.

    I set up Tuners A and B exactly the same way as my old Technomate TM-NANO-3T. ie. Plugged a single LNB into LNB2 on back of receiver, Tuner A - Loop through from Tuner B, Tuner B - Simple, Positioner, Long 000.000, Lat 051.500, Tuner I DVB-T2. However, when highlighting a different satellite to 28.2E, and clicking on to a channel, nothing happens.

    Also when setting up AutoBouquetsMaker and starting Scan, it hangs at 22% and says 'tuning failed fatal.'

    I would appreciate any help, please.

  2. #2
    abu baniaz's Avatar
    Title
    Moderator
    Join Date
    Sep 2010
    Location
    East London
    Posts
    23,335
    Thanks
    6,421
    Thanked 9,146 Times in 6,224 Posts

    Dish not Moving

    describe the wiring/lnb/motor connected to one tuner

    describe the tuner config for this tuner.

    repeat for all tuners. separate answer for each tuner please.

    Better still, draw a picture.

  3. #3

    Title
    Forum Supporter
    Donated Member
    Join Date
    Jan 2012
    Posts
    343
    Thanks
    73
    Thanked 76 Times in 55 Posts
    HI isnt this bit wrong "Simple, Positioner, Long 000.000"

  4. #4
    abu baniaz's Avatar
    Title
    Moderator
    Join Date
    Sep 2010
    Location
    East London
    Posts
    23,335
    Thanks
    6,421
    Thanked 9,146 Times in 6,224 Posts
    Quote Originally Posted by v8rick View Post
    HI isnt this bit wrong "Simple, Positioner, Long 000.000"
    Not necessarily. Just means he is on Greenwich Mean line. So neither east nor west.

    I'm guessing he has a 2nd cable of motorised LNB type of setup.

  5. #5

    Title
    Forum Supporter
    Donated Member
    Join Date
    Jan 2012
    Posts
    343
    Thanks
    73
    Thanked 76 Times in 55 Posts
    Quote Originally Posted by abu baniaz View Post
    Not necessarily. Just means he is on Greenwich Mean line. So neither east nor west.
    .
    Wow thats lucky LOL. never thought of that i live on 3.0404 i always have to remember
    Last edited by v8rick; 10-09-17 at 20:06.

  6. #6

    Title
    Member
    Join Date
    Jan 2015
    Posts
    45
    Thanks
    1
    Thanked 3 Times in 3 Posts
    Sorry. Dont know how to draw onto this forum.
    I am only using one co-axial satellite cable from one LNB on a 1m motorised dish. This cable is plugged into 'LNB2 in', as the paper manual says. ie. LNB1 is not being used.
    I purchased a twin hybrid DVB-C/T/T2 tuner, which I set up OK on Tuner I. I use this for terrestrial, as I have plugged in a roof aerial into the receiver.

    Tuner A: Config Mode Loop through from
    Connected to Tuner B: Vuplus DVB-S NIM(7376 FBC) (DVB-S2)
    Force LNB Power No
    Force ToneBurst No


    Tuner B: Config Mode Simple
    Mode Positioner
    Longitude 000.000 East
    Latitude 051.500 North
    Extra Motor Options No
    Force LNB Power No
    Force ToneBurst No

    Tuner C, D, E, F, G, H and J are inactive.
    I hope this is enough info. This configuration seemed to work OK for the old Technomate.

  7. #7
    abu baniaz's Avatar
    Title
    Moderator
    Join Date
    Sep 2010
    Location
    East London
    Posts
    23,335
    Thanks
    6,421
    Thanked 9,146 Times in 6,224 Posts
    You draw a picture on a piece of paper and attach it. Never mind, your description of of a basic motor setup.

    Does the receiver move the dish if you disable Tuner A?

  8. #8

    Title
    Member
    Join Date
    Jan 2015
    Posts
    45
    Thanks
    1
    Thanked 3 Times in 3 Posts
    No it doesn't. I've even tried plugging into the other input - 'LNB1 in' and disabled Tuner B. Then setting up Tuner A like I did for Tuner B ie. Simple, Positioner etc.
    I just don't understand what I am doing wrong!

  9. #9
    abu baniaz's Avatar
    Title
    Moderator
    Join Date
    Sep 2010
    Location
    East London
    Posts
    23,335
    Thanks
    6,421
    Thanked 9,146 Times in 6,224 Posts
    Attach your settings file. You will find it in /etc/enigma2/ You will need to zip it before you can attach it.


    It may be a loose cable/fitting. Did you change anything else after swapping receivers?

  10. #10

    Title
    Member
    Join Date
    Jan 2015
    Posts
    45
    Thanks
    1
    Thanked 3 Times in 3 Posts
    Nothing changed that I know of. Cable is sound, as I can move dish externally at the motor mount using the inching buttons.
    Been looking for the files you mentioned, but can only find Set up\System\Logs\Settings, but no enigma 2.
    I'm afraid that I need an idiots guide as to where to find this file and how to Zip it. I know how to attach a screen grab to this thread though.

    If its of any help, I installed the same Plugin as with the old Technomate - vhannibal.motor (1.0 + GIT 1310)

  11. #11
    Huevos's Avatar
    Title
    Administrator
    Join Date
    Jun 2010
    Location
    38.5N, 0.5W
    Posts
    13,574
    Thanks
    2,004
    Thanked 4,925 Times in 3,259 Posts
    For a start it should be force lnb power = yes. Force tone = yes.

    Set tuner A to not configure until we get tuner B working right.
    Help keep OpenViX servers online.Please donate!

  12. #12

    Title
    Member
    Join Date
    Jan 2015
    Posts
    45
    Thanks
    1
    Thanked 3 Times in 3 Posts
    Tried that, so I've only tuner B set up, but still no good.
    When I try to move from 28.2E to 13E and click on France 24 for example, at top left corner of TV screen, the dish symbol flashes and counts down, but no dish movement.

  13. #13
    Huevos's Avatar
    Title
    Administrator
    Join Date
    Jun 2010
    Location
    38.5N, 0.5W
    Posts
    13,574
    Thanks
    2,004
    Thanked 4,925 Times in 3,259 Posts
    Is it a direct cable from the STB to the motor? Or does it pass through anything else, like DiSEqC switches or wall plates?
    Help keep OpenViX servers online.Please donate!

  14. #14

    Title
    Member
    Join Date
    Jan 2015
    Posts
    45
    Thanks
    1
    Thanked 3 Times in 3 Posts
    Yes. It is a direct cable from STB through wall and up to motor, with no breaks anywhere for best signal. There is no other equipment like DiSEqC switching.
    The previous Technomate STB one day stopped turning to the satellites in the same way, but as many other functions like abitily to record packed up on me, I bought this new Vu+Solo4K.
    I'm beginning to wonder if, even though the motor turns from activating it outside, its not sending a signal back to the STB.
    Thank you for persevering with this, as I am getting very frustrated.

  15. #15
    abu baniaz's Avatar
    Title
    Moderator
    Join Date
    Sep 2010
    Location
    East London
    Posts
    23,335
    Thanks
    6,421
    Thanked 9,146 Times in 6,224 Posts
    Are you able to test with another cable?

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.