Unable to carry out Software Updates so finally did a Factory reset and still unable. Can anybody help. Many thanks from a raw newbie.
Feeds are down for maintenance is the message.
also posted in wrong forum. Doh
Last edited by Mike j; 18-08-17 at 18:05.
usually can mean your on an old non supported image and would need to upgrade to ,save any important files first but maybe too late now.
http://www.openvix.co.uk/
Mike j (18-08-17)
Hi Can you point me in the right direction to an image to use and the best way to do this as I believe saving files is too late. Before I did the Factory reset the message was that the stb needed reformatting.
Thanks for the help
Use the Image Manager to couch flash your receiver. Download the latest image (5.0.025) from Blue Button > ViX > Image Manager & then press the Yellow Button (Downloads), highlight the latest image & press the Green Button to download. Once the download is completed, press the Red Button to close the download box and then highlight your downloaded image & press the Blue Button to Restore. Simples!!
Sent from my iPhone using Tapatalk
Vu+ Ultimo 4K with 3TB HDD, Dual FBC (Sat) tuners, 1x Twin Hybrid DVB-C/T/T2 tuner
Vu+ Solo 4K with 1TB HDD, Dual FBC (Sat) tuners, 1x Hybrid DVB-C/T/T2 tuner
Vu+ Solo 2 with 1TB HDD 'White Edition', 2x DVB-S2 tuners
Mut@nt HD2400 with 1TB HDD, 4x DVB-S2 tuners
Fixed 28.2E Technomate 65cm Mesh Satellite Dish with Inverto Unicable II/JESS LNB and Inverto Unicable Splitter
Fixed 28.2E Sky Zone 1 45cm Satellite Dish with Octo LNB
(All receivers installed with the latest Dev build)
Mike j (19-08-17)
Best to make a settings backup, as well as image backup before flashing new image.
Mike j (19-08-17)
Keep getting the message there is a problem with the device, please reformat. Does this suggest that the stb needs renewing? ThanksOriginally Posted by Andy_Hazza
faulty usb drive or external hdd powered with recordings,as a format will erase data.
if its a usb used for epg only then you can reformat it again on box and ext3 -ext4. that allows the usb to be used with box.
Mike j (19-08-17)
No USB or hdd has been used so would this suggest the fault lies within the stub itself?
Which image are you on at the moment?
There is nothing wrong with the receiver.
Hi I assume the image is Virtuosso Image Xtreme
Assuming isn't good enough. Providing the proper Image Details is the correct way. Press Menu > Information > About. The latest ViX image (as of 19.08.17) is 5.0.025
Sent from my iPhone using Tapatalk
Vu+ Ultimo 4K with 3TB HDD, Dual FBC (Sat) tuners, 1x Twin Hybrid DVB-C/T/T2 tuner
Vu+ Solo 4K with 1TB HDD, Dual FBC (Sat) tuners, 1x Hybrid DVB-C/T/T2 tuner
Vu+ Solo 2 with 1TB HDD 'White Edition', 2x DVB-S2 tuners
Mut@nt HD2400 with 1TB HDD, 4x DVB-S2 tuners
Fixed 28.2E Technomate 65cm Mesh Satellite Dish with Inverto Unicable II/JESS LNB and Inverto Unicable Splitter
Fixed 28.2E Sky Zone 1 45cm Satellite Dish with Octo LNB
(All receivers installed with the latest Dev build)
Mike j (19-08-17)
Hi I have downloaded the latest 5.0.25 and opened it on the desktop and copied to a USB stick. Image on the stb is dated 2015-03-25 so many image updates since then. Not certain which number is the Vix image detail can you tell me if it is Kernel 3.13.5 Thanks
Last edited by Mike j; 19-08-17 at 16:36.
Save any important files, flash/install the most recent image which you have already downloaded.
Beginning to become a headbanger. USB is obviously being recognised as internal light flashes but will not trigger download to Zero in either USB port. Tried a freshly formatted FAT32 USB and still not recognised. Thanks for the help.
Have you tried Image Manager with this new USB?
Posting Permissions
Reply With Quote