Tuner A settings are not relevant. There is noting attached to tuner a. So whether I set nothing or look-through to be should have no impact.
This is really strange. For the time being I will stick to OpenVix 5.0.020.
Thanks anyway
nekrub2
Tuner A settings are not relevant. There is noting attached to tuner a. So whether I set nothing or look-through to be should have no impact.
This is really strange. For the time being I will stick to OpenVix 5.0.020.
Thanks anyway
nekrub2
VU+ Solo2
USB 32GB used as HDD
Diseq 13.0E 19.0E
If the same hardware works in 5.0 020, it cannot be a hardware issue.
Are you not going to attach your settings file?
Hi Ronand
My problem started with version 5.0.021. When I go back to 5.0.020 all is fine and clear.
So I would assume that it is unlikely that the LNB, the adjustment of the dish or the switch are the root cause of the problem.
Maybe the new vu+ tuner driver sends the signal differently now. Strange enough is also that when I stay on a black station and I do a reboot I get it bright.
Do you know where I can read out the vu+ tuner driver version?
I can predict the answer of VU+ support when I would ask them. “use VU+ original firmware”. This would mean I would loose a lot of good stuff built into OpenVix.
Thanks nekrub2
VU+ Solo2
USB 32GB used as HDD
Diseq 13.0E 19.0E
Last edited by nekrub2; 15-09-17 at 20:48.
VU+ Solo2
USB 32GB used as HDD
Diseq 13.0E 19.0E
etc/enigma2/settings
Gigablue Quad 4K & UE 4K
.........FBC Tuners:
------------------> GT-Sat unicable LNB to 1.5M dish(28.2E)
------------------> Gigablue unicable LNB to 80 cm dish(19.2E)
.......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using unicable ports
Zgemma H9 C/S into Giga4K
nekrub2 (17-09-17)
Dear all
These are the setting files. a) 5.0.20 b) 5.0.026
Hope you can read out something.
Thanks a lot
nekrub2
VU+ Solo2
USB 32GB used as HDD
Diseq 13.0E 19.0E
abu baniaz (19-09-17)
I got a message after switching to Client mode on my Mutant HD1200 -- It read unable to read PAT then something about Data.
And that was on teh latest update as well. May not be connected at all to your issue but thought I would drop in.
Hi FlyiingPig,
Problems reading PAT in both cased. They could be related - even with different error messages.
Hope that one of the cracks find out what is fishy.
Thanks a lot
nekrub2
VU+ Solo2
USB 32GB used as HDD
Diseq 13.0E 19.0E
Posting for reference purposes only
5.0 020
5.0 025Code:config.Nims.0.configMode=loopthrough config.Nims.1.diseqcA=130 config.Nims.1.diseqcB=192 config.Nims.1.diseqcMode=diseqc_a_b
Code:config.Nims.0.configMode=nothing config.Nims.1.diseqcA=130 config.Nims.1.diseqcB=192 config.Nims.1.diseqcMode=diseqc_a_b
Hi Abu Banjaz
I am confused, on tuner A I manually entered loopthrough. When I have time I will redo a plain installation, writing loopthrough again and check what is written in the settings. I never new that there is an option "nothing". Will report soon.
Thanks nekrub2
VU+ Solo2
USB 32GB used as HDD
Diseq 13.0E 19.0E
Hi Abu Banjaz
There is indeed a bug. When setting up the tuner configuration from scratch and you enter loop through the system stores "none". I tested this today. When you modify this at a later stage it keeps loopthrough. > Nevertheless the problem of time-out on reading PAT stays.
Best regards
nekrub2
VU+ Solo2
USB 32GB used as HDD
Diseq 13.0E 19.0E
heebo1974 (24-10-17)
new try with 5.0.031
Couch update from 5.020 - same behaviour as described before PAT timeout. Only the startup station is clear. When I change the startup station the new one is clear and all others have time-out. >> So I go back to 5.0.20 which works perfectly well for TV, Hbbtv, Youtube and most plugins.
VU+ Solo2
USB 32GB used as HDD
Diseq 13.0E 19.0E
heebo1974 (24-10-17)
new try with bulid 5.1.002
USB flashing with 5.1.002 - restore 5.020 settings
Result: Startup channel is clear, when switching to other free channels still PAT time-out.
Conclusion: The bug is obviously not yet fixed. So I go back to 5.0.020.
Last edited by nekrub2; 22-11-17 at 11:11.
VU+ Solo2
USB 32GB used as HDD
Diseq 13.0E 19.0E
Manual installation of build 5.1.003 with USB. No settings restored, signal search done and all setup adaptions made.
Good news: no more PAT time-outs.
Small setback: Restore of setting from 5.0.020 was not possible. It toiok me a while until I had all settings and plugins in place.
Anyway - Thanks a lot to the builders of 5.1.003.
nekrub2
VU+ Solo2
USB 32GB used as HDD
Diseq 13.0E 19.0E
heebo1974 (10-12-17)