Does anyone run cable using one of these tuners? I am get little to no signal on any channels where the frequency is above 690mhz.
Anyone else had any similar issues?
Does anyone run cable using one of these tuners? I am get little to no signal on any channels where the frequency is above 690mhz.
Anyone else had any similar issues?
You need to purchase a decent splitter. Are you subscribed to vm broadband or TV?
Vix image (usually latest) - VU Solo 4K- WD 1TB INTERNAL HDD - DVB-T Freeview, trialling IPTV options
If my response has helped you, don't forget to hit the thanks button below. I appreciate you appreciate me
dpullen87 (11-06-17)
No splitters involved, I’ve tested directly from the cable coming from the brown box. I'm using WF100 cable, I've already changed the isolator to another tratec just in case it was that causing the issue.
All channels perfect signal 90% but as the frequency’s get higher the signal degrades, by the time were up to 600mhz its down to around 40% which is still watchable but once you get towards 700mhz it’s down to less than 10% and is either black or pixelated.
Are you subscribed to vm services?
Vix image (usually latest) - VU Solo 4K- WD 1TB INTERNAL HDD - DVB-T Freeview, trialling IPTV options
If my response has helped you, don't forget to hit the thanks button below. I appreciate you appreciate me
No
Sent from my iPhone using Tapatalk
Vu+ Solo 4k
45.0W - 52.5E
OLED55C6V
You will only get the odd fta channels.
Sent from my iPhone using Tapatalk
Vu+ Ultimo 4K with 3TB HDD, Dual FBC (Sat) tuners, 1x Twin Hybrid DVB-C/T/T2 tuner
Vu+ Solo 4K with 1TB HDD, Dual FBC (Sat) tuners, 1x Hybrid DVB-C/T/T2 tuner
Vu+ Solo 2 with 1TB HDD 'White Edition', 2x DVB-S2 tuners
Mut@nt HD2400 with 1TB HDD, 4x DVB-S2 tuners
Fixed 28.2E Technomate 65cm Mesh Satellite Dish with Inverto Unicable II/JESS LNB and Inverto Unicable Splitter
Fixed 28.2E Sky Zone 1 45cm Satellite Dish with Octo LNB
(All receivers installed with the latest Dev build)
did you not say you had vm broadband
Is this a home made cable? If so have you got continuity between the shells of the F plugs and are the centre 'pins' long enough to make good contact with female mating half?
How to fit an F plug
Has your isolator or splitter have any unused outputs? If so they need to be terminated with a 75 ohm load.Code:http://www.satcure.co.uk/tech/fplugs.htm
Code:http://www.ebay.co.uk/itm/05302-10x-F-type-Male-Plug-Terminator-End-75-Ohm-Connectors-for-F-type-Socket-/271116694395?hash=item3f1fd0737b:g:XOEAAMXQBg5RsIJy
Xtrend ET10K, 2 x satellite tuners 28.2 (Sky FTA), 2 x hybrid (UK Freeview), Zgemma H9S (satellite)
No subscription could equal poor signal buddy, that Mey well be your issue
Vix image (usually latest) - VU Solo 4K- WD 1TB INTERNAL HDD - DVB-T Freeview, trialling IPTV options
If my response has helped you, don't forget to hit the thanks button below. I appreciate you appreciate me
I'm using it on vu solo 2 running cable and sly. All cable channels even ppv when they on. No issues. You need either tv or broadband package with vermin for it work.
Iceman what is your setup please?
E.G. Image used, drivers, any extra telnet commands for it to be configured as a usb tuner? etc
Does EPG work for you? Did you need to set the timeshift to 10 secs (I've read this elsewhere).
Many thanks for your help
Hi bud image is vix 50016. Connect tuner, download driver from plugins on the image and it will recognise your tuner.
Yes EPG works a treat using ABM again from the image. Loads of threads on here how to set up ABM.
No not hat to set timeshift 10 secs? Whats that for?