Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Results 1 to 5 of 5

Thread: **IMPORTANT**Kernel 4.4.8 ET7500 SingleBoot and ET8500 Single/Multiboot Bootloader

  1. #1
    twol's Avatar
    Title
    Moderator
    Join Date
    Apr 2012
    Posts
    8,383
    Thanks
    987
    Thanked 2,888 Times in 2,243 Posts

    **IMPORTANT**Kernel 4.4.8 ET7500 SingleBoot and ET8500 Single/Multiboot Bootloader

    **** Important****

    When the next ViX build 4.1.10, it appears there is a new kernel 4.4.8 and drivers for the Xtrend ET7x00 and ET8500 receivers

    However, it has also been posted that you should/must (?) use a new bootloader (see below)

    As always unzip onto a usb stick and flash as per normal.
    I would then install the new build

    Xtrend-ET7x00-CFE-20160509.zip

    Xtrend-ET8500-CFE-20160509.zip
    Last edited by twol; 12-05-16 at 17:29. Reason: 4.1 009 already being built
    Gigablue Quad 4K & UE 4K
    .........FBC Tuners:
    ------------------> DUR-Line DCR 5-1-8-L4 Multiswitch to 1.5M dish(28.2E)
    ------------------> Spaun SUS 5581/33 NFA Multiswitch to 80 cm dish(19.2E)
    .......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
    AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using Legacy ports on multiswitches
    Zgemma H9 C/S into Giga4K

  2. The Following 6 Users Say Thank You to twol For This Useful Post:

    abu baniaz (12-05-16),Andy_Hazza (12-05-16),Bangord30 (08-09-16),Clabs (15-05-16),rossi2000 (14-05-16),Sicilian (13-05-16)

  3. #2
    twol's Avatar
    Title
    Moderator
    Join Date
    Apr 2012
    Posts
    8,383
    Thanks
    987
    Thanked 2,888 Times in 2,243 Posts
    Thanks for changing the build No and better format ... just went to change it .... but done!

    Changes:-
    Linux Kernel 4.4.8

    DDP(AC3+) Codec added

    DVB-C Subtitle Bug fixed

    Lipsync issue fixed for OE-Alliance image
    Last edited by twol; 12-05-16 at 17:32.
    Gigablue Quad 4K & UE 4K
    .........FBC Tuners:
    ------------------> DUR-Line DCR 5-1-8-L4 Multiswitch to 1.5M dish(28.2E)
    ------------------> Spaun SUS 5581/33 NFA Multiswitch to 80 cm dish(19.2E)
    .......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
    AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using Legacy ports on multiswitches
    Zgemma H9 C/S into Giga4K

  4. The Following User Says Thank You to twol For This Useful Post:

    rossi2000 (14-05-16)

  5. #3
    Sicilian's Avatar
    Title
    The Boss
    Join Date
    Mar 2010
    Posts
    29,645
    Thanks
    23,575
    Thanked 26,044 Times in 7,633 Posts
    Thanks, made a sticky.
    D I S C L A I M E R

    My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!

    Follow us on Twitter 0penViX
    Rules can be found
    HERE
    Support our sponsor World-Of-Satellite
    HERE
    GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
    Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable





  6. #4

    Title
    Forum Supporter
    Donated Member
    Join Date
    Mar 2014
    Posts
    102
    Thanks
    31
    Thanked 7 Times in 6 Posts
    Hi

    I'm going to be flashing an et7500 for a mate. Is this the current bootloader? Is there a reason why there is no bootloader for et7500 on the download page?

    Thanks

  7. #5
    twol's Avatar
    Title
    Moderator
    Join Date
    Apr 2012
    Posts
    8,383
    Thanks
    987
    Thanked 2,888 Times in 2,243 Posts
    Quote Originally Posted by sticky7 View Post
    Hi

    I'm going to be flashing an et7500 for a mate. Is this the current bootloader? Is there a reason why there is no bootloader for et7500 on the download page?

    Thanks
    Yes . You can confirm by going to et-view.net
    Gigablue Quad 4K & UE 4K
    .........FBC Tuners:
    ------------------> DUR-Line DCR 5-1-8-L4 Multiswitch to 1.5M dish(28.2E)
    ------------------> Spaun SUS 5581/33 NFA Multiswitch to 80 cm dish(19.2E)
    .......................> FBC & DVB-S2X into 90cm dish (27.5W) Opticum robust Unicable LNB
    AX HD61, Edision Osmio 4K+, Zgemma H9Combo, Octagon SF8008 , gbtrio4k, h9se using Legacy ports on multiswitches
    Zgemma H9 C/S into Giga4K

  8. The Following User Says Thank You to twol For This Useful Post:

    sticky7 (07-09-16)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.