Cable in correct!!
Cable in correct!!
Octagon SF8008
Going to try an Attenuator see if that work's !!!
Another idea/check. In the first reply it showed you the scan parameters for 6952.
Did you try the other option which is 6887 - then do the complete scan.
I suspect you already tried this, but just in case.
Why dont you try Autobouquetsmaker?
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
abu baniaz (17-07-14)
Try connecting the tuner to your aerial and set to DVB-T2, set your area or European frequencies.. Run a manual scan. Menu > Setup > Service Searching > Manual Scan > Set 'Type of Scan' to Complete. Network search to 'Yes'.
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!
Please help keep OpenViX online, donate HERE.
Rules can be found HERE
Support our sponsor World-Of-Satellite HERE
GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable
Sicilian (17-07-14)
Visited today and all channels for DVB successfully downloaded however there is still an issue with ABM and tuner lock for tuner B so have generated a possible bug report
D I S C L A I M E R
My right to post information is protected under the rights for freedom act. In all instances, information here on my posts are hypothetical in nature, out of curiosity, common knowledge, public knowledge, or role-play. Use of the collective descriptions and knowledge from any of my posts are at YOUR discretion
I am not responsible for what you do with it
Want to know about cardsharing see Here
Want clone support see Here
PM HELP WILL BE IGNORED PLEASE POST IN FORUM AS IT BENEFITS EVERYONE
If you have had a problem that you started a thread about and found your own solution please post back to let everyone know how you solved it
abu baniaz (17-02-16),blackhawkcrow (20-07-14)
are these network id and frequencies still correct?
thanks
Last edited by abu baniaz; 20-07-16 at 02:40. Reason: removed quote
i had same issue on miraclebox, my area net id was not listed in abm, i used bruteforce option and it took 15 minutes to scan 410 channels and they work fine,
also make sure you have right soft cam plugin ticked and enabled. Only the channels are in no order.
Would you mind describing the bruteforce option? I've been sitting on my TM Nano SE Combo since I purchased it because I cannot get it to tune into any channels. I have used what I thought to be the correct Net ID and still nothing. I've kinda been dreading raising a new post to request help, however any assistance would be greatly appreciated.
Why are you dreading it? If you have a non functioning box that can't be fixed/found by using the search option, open a new thread with as much detail on the box used, image used, build used & issue you have.
The more info you provide, the better.
Also, easier for others to point to a fix than guess possible issues.
abu baniaz (20-07-16)