Hello Guest, if you are reading this it means you have not registered yet. Please take a second, Click here to register, and in a few simple steps you will be able to enjoy our community and use our OpenViX support section.
Results 1 to 8 of 8

Thread: How to USB flash GiGaBlue HD 800 SE

  1. #1
    Sicilian's Avatar
    Title
    The Boss
    Join Date
    Mar 2010
    Posts
    29,645
    Thanks
    23,575
    Thanked 26,044 Times in 7,633 Posts

    Thumbs up How to USB flash GiGaBlue HD 800 SE

    Instructions how to USB flash GiGaBlue HD 800 SE.

    1. Download HD 800 SE.
    2. Format a USB stick FAT32.
    2. Extract and copy the following flash files to the ROOT of the USB stick. If using Team Red image, only use the files in the FINISH zip folder: -

    burn.bat
    rootfsn.img
    vmlinux.gz (do not extract the .gz file, copy as is to root of stick)

    4. Make sure the receiver is powered off.
    5. Plug in prepared USB stick to either front or rear USB port.
    6. Power on, the display will show E000 for a couple of seconds then changed to LOAD.
    7. Leave to flash, will take approx 3-5 mins dependant on image size.
    8. GiGaBlue HD 800 SE will automatically reboot once complete.
    D I S C L A I M E R

    My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!

    Follow us on Twitter 0penViX
    Rules can be found
    HERE
    Support our sponsor World-Of-Satellite
    HERE
    GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
    Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable





  2. The Following User Says Thank You to Sicilian For This Useful Post:

    bassethound (22-02-12)

  3. #2
    Rob van der Does's Avatar
    Title
    ViX Beta Tester
    Join Date
    Apr 2010
    Location
    The Netherlands & France
    Posts
    36,259
    Thanks
    1,717
    Thanked 9,461 Times in 6,675 Posts
    And don't forget to remove the stick when the box is up, or the process will be repeated on the next boot.
    I know, sounds pretty straight forward, but I managed to run into that.......
    Last edited by Rob van der Does; 22-02-12 at 07:26.

    Help asked via PM will be ignored.
    The forum is there for help and all will benefit from your questions.
    NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN, IN OPEN FORUM OR PM !

    English is not my native tongue.
    I apologise for all my grammar, spelling and idiom errors.

  4. The Following User Says Thank You to Rob van der Does For This Useful Post:

    Sicilian (22-02-12)

  5. #3

    Title
    Senior Member
    Join Date
    May 2011
    Posts
    205
    Thanks
    126
    Thanked 22 Times in 20 Posts
    Just a quick question do i need to download this before i flash image
    GigaBlue HD 800 SE - E2 PREFLASH ONLY

  6. #4
    Sicilian's Avatar
    Title
    The Boss
    Join Date
    Mar 2010
    Posts
    29,645
    Thanks
    23,575
    Thanked 26,044 Times in 7,633 Posts
    Quote Originally Posted by Wizard55 View Post
    Just a quick question do i need to download this before i flash image
    GigaBlue HD 800 SE - E2 PREFLASH ONLY
    If you Gigablue hd800se already has an Enigma 2 image flashed to it, you only need to flash the finish files.
    D I S C L A I M E R

    My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!

    Follow us on Twitter 0penViX
    Rules can be found
    HERE
    Support our sponsor World-Of-Satellite
    HERE
    GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
    Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable





  7. The Following User Says Thank You to Sicilian For This Useful Post:

    Wizard55 (10-04-12)

  8. #5

    Title
    Member
    Join Date
    Apr 2012
    Posts
    54
    Thanks
    20
    Thanked 15 Times in 3 Posts
    when the image is flashed (i used team red) once the flash is total finished and booted, what should be on screen before you use the remote control.
    i have the gigablue logo and loading, i am not convinced the flash is complete.

    I am so close to chucking this box out the window, does anyone use MSN and perhaps could hold a very frustrated jock

  9. #6
    Stanman's Avatar
    Title
    Junior Admin
    Donated Member
    Join Date
    May 2010
    Posts
    11,284
    Thanks
    1,035
    Thanked 3,599 Times in 2,632 Posts
    If its like any other image, you should get an option to select the video output source etc

    Support The Sponsor - Buy from the best HERE
    Please abide by the rules - have a read HERE
    VIX manual & guides >>HERE
    Download images from >> HERE
    New Box Setup Guide >>HERE

    D I S C L A I M E R
    My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!

    PM HELP WILL BE IGNORED PLEASE POST HERE IN FORUM AS IT BENEFITS EVERYONE


    Follow us on Twitter

    NO CARD SHARING TALK WILL BE TOLERATED, LAN OR WAN! IN OPEN FORUM OR PM

    IF THE POSTS HELP PLEASE CLICK THANKS OR ADD TO REP ?



  10. #7
    digi247
    The Gigablue OpenAAF image is very good i have it on mine and its been rock solid the only problem i have is with the time its always an Hour out no matter what setting i try.

  11. #8
    Sicilian's Avatar
    Title
    The Boss
    Join Date
    Mar 2010
    Posts
    29,645
    Thanks
    23,575
    Thanked 26,044 Times in 7,633 Posts
    Quote Originally Posted by Bluto141 View Post
    when the image is flashed (i used team red) once the flash is total finished and booted, what should be on screen before you use the remote control.
    i have the gigablue logo and loading, i am not convinced the flash is complete.

    I am so close to chucking this box out the window, does anyone use MSN and perhaps could hold a very frustrated jock
    If the receiver is going through the flashing process and your getting the remote control after flashing, the flash is complete. You then go through the startup wizard.

    What exactly are you stuck on? Maybe start a thread with what you're stuck on.
    D I S C L A I M E R

    My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it!

    Follow us on Twitter 0penViX
    Rules can be found
    HERE
    Support our sponsor World-Of-Satellite
    HERE
    GIGABLUE UHD QUAD 4K, VU+ DUO 4K SE, ZGEMMA H7S, VU+ UNO 4K SE
    Triax 1.1m Powered by TM2600, Fixed 28.2 Zone 2 dish with GT-SAT Unicable





Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.